Abstract:Adding Al and Al2O3 powder creates electrical discharge machining (EDM) in a significant machining gap with stable condition. Practically, it is almost impossible to distribute powder particles evenly into the plasma channel. This study investigates the intermolecular process while the plasma channel's pressure and temperature are changed. In our research, surfactant Tween 80® and its effects on intermolecular forces (IMF) through the plasma channel were investigated to evaluate surface quality. In the first phase of our research, output parameters ran at three experimental blocks (without surfactant, with 21.81 g/l of surfactant, and 43.3512 g/l of surfactant) in 17 runs while adding Al and Al2O3 powders with the design of experience (DOE) method by Design Expert software. Decomposition phenomena (DP), adhesion phenomena (AP), and nonuniform distribution (NUD) of Al and Al2O3 powders demonstrated how new molecules (aluminum trihydride, aluminic acid, methyl(methylene)aluminum, hydroxy(methyl)aluminum hydride, hydroxy(methylene)aluminum, and methyl(oxo)aluminum) were created on the surface element composition. In our experiment, powders' even distribution when we decomposed Al and Al2O3 created a more stable plasma channel. Consequently, it led to a more balanced heat transfer on the electrodes' surface. We used scanning of surface quality by field emission-scanning electron microscopy (FE-SEM), electron dispersive spectrum (EDS), and mapping and have shown how to improve the surface defects (hole, crack, and globule). In the second phase of our research, we investigated the intermolecular forces (IMF) on Al–O bond and Al–Al bond. The percentage of elements obtained by mapping analysis of cross-section illustrated that oxygen and aluminum had increased notably when we used Al powder. Considering physical, chemical, metallurgical, and machining time management (MTM) of PM-EDM, we demonstrated that the fine finishing surface improved by 217.7% at Ip = 15 A and Ton = 50 μs and Cp = 5 g/l when the surfactant was added. We compared the best-optimized points in the final phase of our work and measured the recast layer thickness (RLT) after adding Al and Al2O3. As a result, the RTL was removed entirely when Al was added to the dielectric. We have shown that MRR (g/h) and TWR (g/h) were decreased by 5.23 and 113.36%, and SR (Ra) and machining time were increased by 21.75 and 50.84%, respectively. We note that high strength-to-weight ratio and corrosion resistance are essential for many industries, particularly aerospace and biomedical industries. We believe that these industries can potentially benefit from our study.

Performance comparison of powder mixed EDM and traditional EDM on TZM-molybdenum super alloy using response surface methodology

Numerical analysis of the powder mixed electrical discharge machining (PMEDM) process for TZM-molybdenum superalloy using finite element method

Optimization of EDM Machining of High Carbon High Chromium Steel Using Zirconium and Nickel Powder Mixed Dielectric by Grey Relational Analysis

Parameter optimization in the enhancement of MRR of titanium alloy using newer mixing method in PMEDM process

Powder Mixed Dielectric: An Approach for Improved Process Performance in EDM

Optimizing the powder mixed EDM process of nickel based super alloy

Near Dry Powder Mixed Electric Discharge Machining of AA7050 Hybrid Composites Utilizing Composite Tool Materials

Machinability investigation and surface modification of nano-TiB2 and AlN grafted MWCNT hybridized Al 7075 matrix ternary composite through powder-mixed EDM

Performance and surface alloying characteristics of Cu–Cr and Cu–Mo powder metal tool electrodes in electrical discharge machining

Electric Discharge Machining of Titanium Alloy under Cu Mixed Dielectric Medium

Improvement of process performance of powder mixed electrical discharge machining by optimisation -A Review

Powder mixed-electrical discharge machining (EDM) with the electrode is made by fused deposition modeling (FDM) at Ti-6Al-4V machining procedure

Surface Modification of Magnesium Alloy AZ91D Using Nanopowder Mixed Electrical Discharge Machining for Biodegradable Implant

Study of surfactant effects on intermolecular forces (IMF) in powder-mixed electrical discharge machining (EDM) of Ti-6Al-4V

Process parameters optimization of EDM for hybrid aluminum MMC using hybrid optimization technique

Investigation on the Effect of Different Dielectric Fluids During Powder Mixed EDM of Alloy Steel

Experimental investigation and performance enhancements characteristics of gaseous assisted powder mixed near dry electric discharge machining

Study of Correlation of Machining Performance and Geometrical Tolerances of Si3N4-TiN Composites Using EDM Process

Performance analysis of powder-assisted micro-drilling operation using micro-EDM

Optimization of the Material Removal Rate and Electrode Wear Ratio in Electrical Discharge Machining of Reaction-bonded Silicon Carbide by Response Surface Methodology

Performance Evaluation of Si–Cu-Hybrid Dust as a Powder Additive of EDM Dielectrics to Machine Ti6Al4V with Copper Electrode