Abstract:Nb3Sn conductors are important candidates for high-field magnets for particle accelerators, and they continue to be widely used for many laboratory and NMR magnets. However, the critical current density, Jc, of present Nb3Sn conductors declines swiftly above 12-15T. State-of-the-art Ta- and Ti-doped strands exhibit upper critical field, Hc2, values of 24-26.5T (4.2K) and do not reach the FCC target Jc, which serves as the present stretch target for Nb3Sn development. As recently demonstrated, to meet this goal requires enhanced vortex pinning but an independent and supplementary approach is to significantly enhance Hc2. In this study, we have arc-melted multiple Nb alloys with added Hf, Zr, Ta and Ti and drawn them successfully into monofilament wires to investigate the possibilities of Hc2 enhancement through alloying. Hc2(T) was measured for all samples in fields up to 16T and some up to 31T. We have found that all alloys show good agreement with the standard Werthamer, Helfand, and Hohenberg (WHH) fitting procedure without the need to adjust the paramagnetic limitation parameter (alpha) and spin-orbit scattering parameter (lambda_so). The evaluation of dHc2/dT near Tc, which is proportional to the electronic specific heat coefficient (gamma) and the normal state resistivity (rho_n), allows a better understanding of the induced disorder introduced by alloying in the A15 phase. So far, we have observed that Hf alloying of pure Nb can enhance Hc2(0) by 3-4T to 28T, while adding just 1 at. %Hf or Zr into a Nb4Ta base alloy can raise Hc2(0) to 31T. Very importantly we find that Hf and Zr raise the alloy recrystallization temperature above the usual A15 reaction temperature range of 650°C-750°C, thus ensuring denser A15 phase nucleation in the Nb alloy grain boundaries, possibly leading to a more homogeneous A15 phase Sn content and refined A15 grain size. The potential for...

A15 Phase Formation Kinetics Study of Mono-Element Internal-Sn Nb3sn Superconducting Wires

Formation and upper critical fields of the two distinct A15 phases in the subelements of Powder-In-Tube Nb3Sn wires

Preparation of Nb 3 Al Superconductor by Powder Metallurgy and Effect of Mechanical Alloying on the Phase Formation

Preparation of Nb3al by High-Energy Ball Milling and Superconductivity

Influence of Nb Alloying on Nb Recrystallization and the Upper Critical Field of Nb3Sn

Crystallization kinetics and magnetic properties of Fe 63.5Co10Si13.5B9Cu 1Nb3 nanocrystalline powder cores

Niobium based intermetallics as a source of high-current/high-magnetic field superconductors

Fabrication of Nbti Superconducting Joint by Electromagnetic Forming Method

Development of Electromagnetic Forming Nbti Superconducting Joint

Improved critical current density of Cu-doped Nb3Al wire through optimized Rapid-Heating Quenching and Transformation method

Unveiling the nucleation and growth of Zr oxide precipitates of internally oxidized Nb3Sn superconductors

Microstructure identification of powder in tube Nb3Al wires during rapid heating process and properties of the transformed superconductors

Effect of Cu doping on properties of RHQT processed powder in tube Nb3Al wires

Fabrication and Performance of Nb3Sn Superconducting Joints

Study of Fault Conditions During Heat Treatment of Nb3Sn Strand

Application of Thermal Analysis Technology to Diffusion Heat Treatment Processing of Nb3Sn Multifilamentary Superconductors

Development Of Nb3sn Superconducting Coil Manufacture Technology

Characterization and Analysis of Microstructures of Nb_3Sn Multifilamentary Superconductors during Diffusion Treatment by Bronze Route

Phase formation and transport properties of vapor-solid reacted AIMI MgB2 superconductors

Synthesis of new high-entropy alloy-type Nb3 (Al, Sn, Ge, Ga, Si) superconductors

Effect of Hf Addition to Nb on Nb 3 Sn Grain Morphology Under High Sn Diffusion Driving Force