Abstract:The sole micropores strictly restrict the wide utilization of TS-1 zeolite in the catalytic fields, especially in the catalytic conversion of compounds with large molecular sizes. Here, we report a feasible and economical method to overcome this drawback. In this work, the hierarchical TS-1 zeolite was constructed via post-acid treatment, post-alkali etching, and a combination of post-acid treatment and alkali etching methods, after which, the corresponding NiMo-supported catalysts were prepared via the incipient wetness impregnation method. Then, the aforementioned materials were fully characterized using X-ray diffraction (XRD), N-2 adsorption-desorption, pyridine adsorbed Fourier transform infrared spectroscopy (Py - FTIR), H-2 temperature programmed reduction (H-2 - TPR), X-ray photoelectron spectroscopy (XPS), and high-resolution transition electron microscope (HR-TEM) to unravel the changes in the physicochemical properties caused by the post treatments. Finally, the hydrodesulfurization of dibenzothiophene (DBT) was used as a probe to assess the effects of the post-treatments on the catalytic performance of the hierarchical NiMo/TS-1 catalysts. The results showed that the MFI topology of TS-1 zeolite remained undamaged significantly and the serial hierarchical TS-1 zeolites exhibited higher specific surface areas and mesopore structures. Moreover, appropriate amounts of Bronsted acid sites were formed at the surface of the serial hierarchical TS-1 zeolites. The interaction between the active metals and the support materials was also modulated by the post-treatment of TS-1 zeolite, which resulted in better dispersion of Ni promoted MoS2 slabs with a higher proportion of NiMoS active phase, further leading to the enhanced catalytic activity and direct desulfurization pathway selectivity of the corresponding serial hierarchical NiMo/TS-1 catalysts. Among all the prepared catalysts, the catalytic activity was enhanced by approximately 1.2 times over catalyst NiMo/AT-TS-1 obtained by post-acid treatment compared to that over catalyst NiMo/TS-1 without treatment and on which the selectivity of the DDS pathway was 22% higher compared to that over catalyst NiMo/TS-1.

Preparation, characterization, and catalytic properties of the Mo 2C/SBA-15 catalysts

Synthesis of Novel NiMo Catalysts Supported on Highly Ordered TiO2-Al2O3 Composites and Their Superior Catalytic Performance for 4,6-Dimethyldibenzothiophene Hydrodesulfurization

Catalytic Characteristics of Active Corner Sites in CoMoS Nanostructure Hydrodesulfurization – A Mechanism Study Based on DFT Calculations

Comparative Study on Molybdenum Nitride, Phosphide and Carbide

Hierarchical TS-1 zeolite loaded with NiMo catalysts: Preparation and performance in hydrodesulfurization

Mesoporous Carbon Supported Co-Mo and Ni-Mo Catalysts for Hydrodesulfurization

Hydrodesulfurization Performance of Co-Mo/Al2O3-TiO2 Catalyst Prepared by Urea Matrix Combustion Method

Adsorption and Reaction of Thiophene and H2S on Mo2C/Al2O3 Catalyst Studied by in Situ FT-IR Spectroscopy

Enhanced hydrodesulfurization activity of thiophene over hollow tubular CoMo unsupported catalysts

Support Effects on Thiophene Hydrodesulfurization over Co-Mo-Ni/Al2O3 and Co-Mo-Ni/TiO2-Al2O3 Catalysts

Hydrodesulfurization Catalyst Prepared by Urea-Matrix Combustion Method

Synthesis and Characterization of Molybdenum Carbide Catalysts on Different Carbon Supports

Construction of High Content CoMoS Active Sites Through the Combination of Co 5 Mo 10 Molecular Precursors and Inert Carbon Matrix Support for Deep Hydrodesulfurization

Preparation, Characterization and Desulfurization Performance of Cu/Ti-MCM-41 and Cu/Ti-HMS Catalysts

Electronic structure regulation of CoMoS catalysts by N, P co-doped carbon modification for effective hydrodesulfurization

Hydrodesulfurization of Thiophene in n-Heptane Stream Using CoMo/SBA-15 and CoMo/AlSBA-15 Mesoporous Catalysts

In Situ Ft-Ir Spectroscopic Studies Of Sulfur Effect On Mo2c/Al2o3 Catalyst.

Hydroisomerization of Model Naphtha over Sulfided Co-Mo/SBA-15 Catalyst

Effect of sulfiding conditions on the hydrodesulfurization performance of the ex-situ presulfided CoMoS/γ-Al2O3 catalysts

Influence of Carbonization Conditions on Structural and Surface Properties of K-Doped Mo2C Catalysts for the Synthesis of Methyl Mercaptan from CO/H2/H2S

SBA-15-supported ultrastable Mo 2 N@CN catalysts for hydrodeoxygenation of guaiacol