Abstract:In this paper, the synthesis of poly(3,4-ethylenedioxythiophene) (PEDOT) by cyclic voltammetry (CV) electrochemical deposition and its application in the counter electrode of solid-state dye-sensitized solar cells were studied. The influence of cycle times (10 similar to 50 times) on the morphology, thickness and optical properties of PEDOT films were explored by Fourier transform infrared spectroscopy (FTIR), atomic force microscope (AFM), scanning electron microscope (SEM) and ultraviolet-visible spectroscopy (UV-Vis). The photoelectrochemical properties of solid-state dye-sensitized solar cells based on PEDOT transparent counter electrode were characterized by J-V, electrochemical impedance spectroscopy (EIS), intensity modulated photocurrent spectrum/photovoltage spectrum (IMPSNS) and Tafel analysis. The results showed that an un-uniform film with the thickness of 0.5 mu m and light transmittance of 80% was formed when CV cycle times was 10, where the PEDOT film was not completely covered on the substrate. When the CV cycles reached 30 similar to 40, a uniform and dense transparent film was obtained and the highest photo-electric conversion efficiency of the corresponding solid-state dye-sensitized solar cells reached 5.34%. This is because uniform and dense surface, good optical properties and high photo- electric catalysis properties (J(0) =2.51 X 10(-3) A.cm(-2)) for I-3 in the electrolyte, made the device obtain larger diffusion coefficient (D-n=28.80 mu m(2).ms(-1)) and carrier diffusion length (L = 21 .41 mu m), which were favorable for charge transfer. When the number of CV cycles was further increased to 50 times, showing greater roughness, the PEDOT fihn was no longer growing uniformly. The PEDOT film deposited on the FTO surface underwent some dissolution and desorption, the PEDOT film became uneven, and the catalytic activity of PEDOT electrode to I-3(-) in electrolyte was reduced. The device with PEDOT transparent counter electrode fihn deposited by cyclic voltammetry could also achieve double-side illumination with good catalytic activity to the electrolyte. Under the condition of double-side illumination, the photoelectric performance of the device using electrodeposited PEDOT as transparent counter electrode was improved by about 20%. The improvement of the photoelectric performance of the device is mainly due to the increase in the absorption of photons by the double-sided illumination.

Polymer Photovoltaic Cell UsingTiO2/G-PEDOT Nanocomplex Film As Electrode

Hybrid inverted organic photovoltaic cells based on nanoporous TiO2 films and organic small molecules

A Poly(3,4-Ethylenedioxythiophene):Poly(styrene Sulfonic Acid)/titanium Oxide Nanocomposite Film Synthesized by Sol–gel Assisted Electropolymerization for Electrochromic Application

Enhanced Electrochromic Properties of Donor–acceptor Polymers Via TiO2 Composite

An In-Situ Synthesized Pedot:Pss/Tio2 Nanocomposite Film by Electropolymerization and Its Enhanced Electrochromic Properties

Ti 3 C 2 T x /PEDOT:PSS Composite Interface Enables over 17% Efficiency Non-fullerene Organic Solar Cells

Electrochemical Synthesis of PEDOT and Its Application in Solid-State Dye-sensitized Solar Cells

Fabrication of TiO 2 nanorod array/semiconductor nanocrystal hybrid structure for photovoltaic applications

A dye-sensitized solar cell based on natural photosensitizers and a PEDOT:PSS/TiO2 film as a counter electrode

Nanofabrication of organic/inorganic hybrids of TiO2 with substituted phthalocyanine or polythiophene

Nanotube and poly(3,4-ethylenedioxythiophene):polystyrene sulfonate (PEDOT:PSS) composite film for the electrode applications in organic thin-film transistor and dye-sensitized solar cells

Nanoporous TiO2/SnO2/Poly(3,4-ethylene-dioxythiophene): Polystyrenesulfonate Composites As Efficient Counter Electrode for Dye-Sensitized Solar Cells

Application of Electrochemical Impedance Spectroscopy in Organic Solar Cells with Vertically Aligned Tio2 Nanorod Arrays As Buffer Layer

Application of Electrochemical Impedance Spectroscopy in Organic Solar Cells with Vertically Aligned TiO<sub>2</sub> Nanorod Arrays as Buffer Layer

Digital printing of a novel electrode for stable flexible organic solar cells with a power conversion efficiency of 8.5%

A Polymeric Two‐in‐One Electron Transport Layer and Transparent Electrode for Efficient Indoor All‐Organic Solar Cells

TiO2 nanoparticles via simple surface modification as cathode interlayer for efficient organic solar cells

Flexible ITO‐Free Organic Photovoltaics on Ultra‐Thin Flexible Glass Substrates with High Efficiency and Improved Stability

Ferrocene‐terminated Perylene Diimide based Small Molecular Electrolyte as Electron Transport Layer for Efficient Organic Solar Cells

Compatible Solution‐Processed Interface Materials for Improved Efficiency of Polymer Solar Cells

Solution-processed, semitransparent organic photovoltaics integrated with solution-doped graphene electrodes