Abstract:Cathode buffer layer (CBL) is one of the key issues influencing the performance of organic solar cells. In this article, a nanocomposite of zinc oxide nanoparticles (ZnO) together with a conjugated polymer, poly[(9,9-bis(3'-(N,N-dimethylamino)propyl)-2,7-fluorene)-alt-2,7-(9,9-dioctyl)-fluorene] (PFN) was developed, and used as the CBL for solution processed inverted organic solar cells (OSC). In comparison with the bare ZnO, PFN or ZnO/PFN stacked layer, the ZnO:PFN nanocomposite CBL employing device showed superior device performance, in particular significantly improved fill factor. Optimized power conversion efficiency (PCE) of P3HT:PC61BM and PTB7:PC61BM device using ZnO:PFN composite CBLs reached to 3.56% and 7.17%, respectively. Influences of the mixing ratio and the layer thickness of the ZnO:PFN nanocomposite CBL on solar cell performance were carefully studied, and results indicated that ZnO:PFN CBL showed a wide tolerance of blend ratio and layer thickness. In particular, no obvious thickness dependent-device performance was found, even when the CBL layer thickness was higher than 125nm, providing a good printing processibility of the nanocomposite. Photoelectron spectroscopy, photoluminescence, as well as electric conductivity of the ZnO:PFN films were studied, and the results were compared with that of the other three reference CBLs. Results demonstrated that the interaction between ZnO and PFN decreases the work function of the blended film, leading to a more favorable energy level alignment for electron injection at the interface. Analysis on the dark J–V curves of the solar cells revealed that device using ZnO:PFN CBL had the best diode characteristics including lowest reverse saturated current density (J0), ideal factor (n), and series resistance (Rs), and highest shunt resistance (Rsh). Such an improvement was ascribed to the defect passivation by the conjugated polymer, which led to an improved charge carrier selectivity of the CBL and consequently enhanced the FF of the solar cells. In addition, long-term stability of organic solar cells was also improved by using ZnO:PFN nanocomposite as the CBL. The current work provides a valuable guideline for the development of high performance cathode buffer layer material for printable organic solar cells.

Role of Buffer in Organic Solar Cells Using C60 As an Acceptor

Electron conducting buffer layers in organic photovoltaics

Effect of buffer layers on the performance of organic photovoltaic cells based on copper phthalocyanine and C60

The Study on Organic Solar Cells Based on Bathocuproine As an Exciton Blocking Layer

Crown-Ether Functionalized Fullerene As A Solution-Processable Cathode Buffer Layer For High Performance Perovskite And Polymer Solar Cells

Application of Buffer Layer to Improve the Efficiency of Organic Solar Cells

Organic Photovoltaic Cells with Improved Performance Using Bathophenanthroline As a Buffer Layer

[6,6]-Phenyl-C61-butyric acid dimethylamino ester as a cathode buffer layer for high-performance polymer solar cells

Significant Enhancement in Built-In Potential and Charge Carrier Collection of Organic Solar Cells Using 4-(5-hexylthiophene-2-yl)-2,6-bis(5-trifluoromethyl)thiophen-2-yl)pyridi Ne As A Cathode Buffer Layer

Research Progress on Inorganic Buffer Layer Materials in Organic-Inorganic Hybrid Solar Cells

Authigenic Buffer Layer: Tuning Surface Work Function in All Polymer Blend Solar Cells

Zinc Oxide: Conjugated Polymer Nanocomposite As Cathode Buffer Layer for Solution Processed Inverted Organic Solar Cells

Investigating the Role of Cathode Buffer Layers based on Zinc Oxide with Surface‐rich Graded Fullerene Isomers in Tuning the Interfacial Properties of Organic Solar Cells

Effect of cathode buffer layer on the stability of polymer bulk heterojunction solar cells

Optoelectronic Analysis of Organic Solar Cells with Bphen as a Buffer Layer

Sb2o3 Anode Buffer Induced Morphology Improvement in Small Molecule Organic Solar Cells

Interfacial Processes in Small Molecule Organic Solar Cells

The characteristics of the small molecule organic solar cells with PEDOT:PSS/LiF double anode buffer layer system

Organic Photovoltaic Cells Based on TPBi As a Cathode Buffer Layer

Efficient Cathode Buffer Material Based on Dibenzothiophene- S, S-dioxide for Both Conventional and Inverted Organic Solar Cells

5-Nm LiF As an Efficient Cathode Buffer Layer in Polymer Solar Cells Through Simply Introducing a C60 Interlayer