Multimode Fiber Loop Ring Down Spectroscopy for Pressure Measurement

Huiye Qiu,Yishen Qiu,Zhihao Chen,Baoyu Fu,Xiyao Chen,Gaoming Li

DOI: https://doi.org/10.1109/cleo.2007.4452807

2007-01-01

Abstract:We demonstrate a multimode fiber loop ring down spectroscopy for pressure measurement with higher sensitivity over larger dynamic range of measurement compared with single mode fiber counterpart.

What problem does this paper attempt to address?

Multimode Fiber Ring‐down Pressure Sensor

Huiye Qiu,Yishen Qiu,Zhihao Chen,Baoyu Fu,Xiyao Chen,Gaoming Li

DOI: https://doi.org/10.1002/mop.22553

IF: 1.311

2007-01-01

Microwave and Optical Technology Letters

Abstract:A fiber-loop ring-down spectroscopy based on multimode fiber is proposed for pressure measurement. It has been found that the multimode fiber-loop ring-down pressure sensor has higher sensitivity and larger dynamic range up to 62 X 10(7) Pa compared to the single mode counterpart. Good stability and repeatability of the sensor are also demonstrated. (C) 2007 Wiley Periodicals, Inc.
Strain Measurement by Fiber-Loop Ring-Down Spectroscopy and Fiber Mode Converter

Huiye Qiu,Yishen Qiu,Zhihao Chen,Baoyu Fu,Gaoming Li

DOI: https://doi.org/10.1109/jsen.2008.926884

IF: 4.3

2008-01-01

IEEE Sensors Journal

Abstract:A multimode fiber-loop ring-down spectroscopy combined with a fiber mode converter for strain measurement is presented. The bending loss theory in multimode fibers is used for the explanation of strain induced ring down cavity loss mechanism, which agrees well with the experimental results. With this technique, strain measurement is achieved in a time domain by measuring the ring-down time. The strain sensing system is demonstrated with good linear response, good stability and high resolution as small as 0.33 mu epsilon over a rang of 800 mu epsilon.
Fiber Mode Converter Incorporated Fiber Ring-Down Strain Sensor

Huiye Qiu,Yishen Qiu,Zhihao Chen,Baoyu Fu,Gaoming Li

DOI: https://doi.org/10.1117/12.738377

2007-01-01

Abstract:We present a fiber mode converter incorporated fiber-loop ring-down system for strain measurement. The sensing system consists of a fiber mode converter and a typical fiber-loop ring-down system including a pulsed VCSEL laser diode at 350 nm, multimode fiber couplers, multimode fiber loop, photo-receiver and high-speed data acquisition and signal processing. The bending multimode fiber-loop ring-down strain sensor is demonstrated with a resolution of 0.28 mu epsilon over a range of 767 mu epsilon.
&Lt;title>distributed Optical Fiber Pressure Sensor</title>

Hongbo Lu,Xingchun Chu,Wenjian Luo,Tingzheng Shen,Huayong Yang

DOI: https://doi.org/10.1117/12.318169

1998-01-01

Abstract:A new kind of distributed fiber optic sensor is described in the paper. On the basis of mode coupling between two orthogonal fundamental modes of HiBi polarization- maintaining fiber, a new method is developed to locate the mode coupling point caused by external pressure applied on the fiber.
Dual-Parameter Active Fibre Sensor Based On Modal Interference In Few-Mode Fibres

Hongdan Wan,Hongye Li,Zuxing Zhang,Chao Pan,Bing Sun,Changle Wang,Lin Zhang

DOI: https://doi.org/10.1109/icocn.2016.7875831

2016-01-01

Abstract:We propose a dual-parameter active fibre sensor based on a fibre ring laser using a single-mode-two-mode-single-mode (STS) fibre interferemeter and a four-mode FBG as the intracavity dual-parameter sensing element. The interferometric spectra of the STS are investigated with different core-offset parameters and few-mode fibre length. The highest LP11 mode excitation ratio is achieved with a 6 mu m core-offset distance in the STS which achieves best sensing ability. High precision dual-parameter sensing of pressure and tension are achieved experimentally by measurements of fibre laser output wavelength and intensity.
Four-Channel Fiber Loop Ring-Down Pressure Sensor with Temperature Compensation Based on Neural Networks

Yang Gao,Yishen Qiu,Huaixi Chen,Yan Huang,Gaoming Li

DOI: https://doi.org/10.1002/mop.25326

IF: 1.311

2010-01-01

Microwave and Optical Technology Letters

Abstract:A four-channel fiber loop ring-down pressure sensor with temperature compensation based on neural networks is described. This fiber ring-down pressure sensor makes use of the principle of time division multiplexing, which consists of series and parallel fiber loops. The laser pulses from four-channels can he acquired by only one detector and the four pressure values are measured synchronously in our experiment. Taking mode dispersion in multimode fiber into consideration, the maximum multiplexing number is discussed. In addition, temperature compensation based on neural networks has been successfully used in our experiment, to eliminate the disturbance of environmental temperature. (C) 2010 Wiley Periodicals, Inc. Microwave Opt Technol Lett 52: 1796-1799, 2010; Published online in Wiley InterScience (www.interscience.wiley.com). DOI 10.1002/mop.25326
Fiber Optic Pressure Sensor Based on Polarization-Maintaining Photonic Crystal Fiber for Downhole Application

H. Y. Fu,Chuang Wu,M. L. V. Tse,Lin Zhang,H. Y. Tam,Bai-Ou Guan,C. Lu,P. K. A. Wai

DOI: https://doi.org/10.1117/12.835261

2009-01-01

Abstract:We experimentally demonstrate a high pressure sensor based on a polarization-maintaining photonic crystal fiber (PMPCF) with Sagnac loop configuration for downhole application. The pressure sensitivity of the proposed sensor is 4.21 nm/MPa and 3.27 nm/MPa at ~1320 nm and ~1550 nm respectively. High pressure measurement up to 20 MPa has been achieved in our experiment. The sensor also shows reduced temperature sensitivity, making it an ideal candidate for pressure sensing in harsh environment.
Large dynamic range pressure sensor based on two semicircle-holes microstructured fiber

Zhengyong Liu,Lin Htein,Kang-Kuen Lee,Kin-Tak Lau,Hwa-Yaw Tam

DOI: https://doi.org/10.1038/s41598-017-18245-6

IF: 4.6

2018-01-08

Scientific Reports

Abstract:This paper presents a sensitive and large dynamic range pressure sensor based on a novel birefringence microstructured optical fiber (MOF) deployed in a Sagnac interferometer configuration. The MOF has two large semicircle holes in the cladding and a rectangular strut with germanium-doped core in the center. The fiber structure permits surrounding pressure to induce large effective index difference between the two polarized modes. The calculated and measured group birefringence of the fiber are 1.49 × 10−4, 1.23 × 10−4, respectively, at the wavelength of 1550 nm. Experimental results shown that the pressure sensitivity of the sensor varied from 45,000 pm/MPa to 50,000 pm/MPa, and minimum detectable pressure of 80 Pa and dynamic range of better than 116 dB could be achieved with the novel fiber sensor. The proposed sensor could be used in harsh environment and is an ideal candidate for downhole applications where high pressure measurement at elevated temperature up to 250 °C is needed.

multidisciplinary sciences
Research on Fiber Grating Sensing to Fiber Loop Ringdown

Weihua Zhang,Bo Liu,Jianhua Luo,Xiaoyi Dong

DOI: https://doi.org/10.1117/12.783296

2007-01-01

Abstract:A fiber loop consists of two couplers and a single mode fiber and the measured pressure is converted into ringdown time of light traveling in the fiber loop by the sensor element of FBG. When pressure is changed, the pressure will be directly proportional to the ringdown time which is identical to that of theory. This kind of system of measuring press based on the theory has advantages of simple composition and convenient measure and it provides a novel method of fiber gratting demodulation technology and has practical value. Apart from measuring press, it can measure temperature and other parameters.
High sensitivity pressure sensor based on a simple SPS fiber loop mirror

Hanglin Lu,Yalan Niu,Jian Tang,Li Yang,Laipeng Shao,Junhui Hu

DOI: https://doi.org/10.1007/s11082-021-02971-3

IF: 3

2021-07-22

Optical and Quantum Electronics

Abstract:A high sensitivity pressure sensor based on a single mode-polarization-maintaining-single mode fiber (SPS) structure fiber loop mirror is proposed and experimentally demonstrated. The sensing structure is fabricated by simply splicing a section of polarization-maintaining fiber (PMF) between two pieces of single mode fibers. The effect of PMF length on the sensing performance is experimentally studied. The results show that the PMF length has a significant influence on pressure sensitivity. The proposed sensor exhibited a high pressure-sensitivity of 7.896 nm/kPa when the length of PMF is 7 cm. The sensor has the advantages of simple structure and easy fabricate and high sensitivity.

engineering, electrical & electronic,optics,quantum science & technology
Sensitivity-Enhanced Fiber-Optic Sensor in a Microwave Photonics Fiber Loop Ringdown System

Chen Zhu,Yiyang Zhuang,Jie Huang

DOI: https://doi.org/10.1109/jlt.2022.3179813

IF: 4.7

2022-08-05

Journal of Lightwave Technology

Abstract:Chen Zhu, Yiyang Zhuang, Jie Huang In this article we report a microwave photonics fiber loop ringdown (MWP-FLRD) interrogated fiber-optic sensor with enhanced sensitivity. A ... [J. Lightwave Technol. 40, 5768-5774 (2022)]

engineering, electrical & electronic,optics,telecommunications
Wide-range Optical Sensors Based on a Single Ring Resonator with Polarization Multiplexing

Yongheng Yue,Huihui Zhu,Ziwei Cao,Jianjun He,Mingyu Li

DOI: https://doi.org/10.3788/col201917.031301

IF: 2.56

2019-01-01

Chinese Optics Letters

Abstract:Wide-range optical sensors based on a single ring resonator are investigated theoretically and experimentally. The sensor worked at the TE and TM modes simultaneously. Because the sensitivities of the TE mode and TM mode are different, the TE mode is used for the large measurement range, and the TM mode is used for the high sensitivity measurement. The experimental results showed that the measurement range for the TE mode was almost three times larger than that of the TM mode. A sensitivity of 233 nm/RIU was achieved for the wavelength interrogation of the TM mode.
Simultaneous Measurement of Force and Temperature by a Multi-Position Fiber Loop Ringdown Sensor Array

Ruoming Li,Chao Tian,Yunlong Zhang,Jintao Zhang,Xuefeng Chen,Shengchun Liu

DOI: https://doi.org/10.1109/jlt.2015.2446652

IF: 4.7

2015-01-01

Journal of Lightwave Technology

Abstract:A multi-sensor addressing method for fiber Bragg grating aided fiber loop ringdown (FBG-FLRD) sensor array is proposed. It is capable of simultaneous measurement of temperature and force. Light from a wavelength-swept fiber laser (WSFL) is modulated into pulsed light to illuminate FBG-FLRD sensor array. Based on the time sequence of pulsed lights reflected by fiber Bragg grating array, each FBG-FLRD sensor can be distinguished. The time interval between the trigger signal of the WSFL and the pulsed light reflected by FBG offers temperature variation information. By measuring the ringdown time of each FBG-FLRD, the loss of fiber ring induced by temperature and force can be obtained. And then simultaneous measurement can be implemented in real time. To prove the validity of the proposed system, a six elements array is experimentally validated with interrogation frequency of 27.5 Hz.
Dual-Channel Fiber Ring Down Force Sensor

Gaoming Li,Yishen Qiu,Baoyu Fu,Zhihao Chen,Huiye Qiu

DOI: https://doi.org/10.1117/12.738599

2007-01-01

Abstract:Dual-channel fiber ring down force sensor based on the principle of time division multiplexing is descried. The system has the capability to interrogate more than two micro bend sensors by using more than one fiber delay line to control the time of flight of the pulse. The dual-channel fiber ring down force sensor with one fiber delay coil is demonstrated with high force sensitivities of 183.4ns/N and 163.6ns/N. respectively. Our system has also good linear responses.
Diaphragm-Structured Fiber-Optic Pressure Sensors for Oil Downhole Applications

Xiaosa Hu,Dan Su,Xueguang Qiao

DOI: https://doi.org/10.1109/jsen.2024.3376085

IF: 4.3

2024-05-03

IEEE Sensors Journal

Abstract:We propose a fiber-optic Fabry–Pérot interferometer (FPI) pressure sensor that utilizes a diaphragm structure interfacing with the flat-cut end face of a single-mode fiber (SMF). The application of pressure results in the deformation of the diaphragm, which is analyzed using wavelength tracking and cavity length (CL) demodulation techniques. To compensate for temperature effects, fiber Bragg grating (FBG) is connected in series. The sensor exhibits a sensitivity of 4.33 pm/MPa when utilizing wavelength shift and 1.83 nm/MPa when measuring CL change within a pressure range of 0–80 MPa and a temperature of 150 °C. Due to its extensive dynamic range, heightened sensitivity, and excellent temperature resistance, this sensor is used to monitor pressure changes in 3500-m-deep oil wells.

engineering, electrical & electronic,instruments & instrumentation,physics, applied
Dynamic Distributed Brillouin Optical Fiber Pressure Sensor

Liqiang Qiu,Qi Chu,Tianfu Li,Yongkang Dong

DOI: https://doi.org/10.1117/12.2599261

2021-01-01

Abstract:A dynamic distributed Brillouin optical fiber pressure sensor based on frequency agility technology is proposed, and the performance of dynamic and static pressure sensing is experimentally demonstrated. A set of frequency-agile pump pulse sequences with single pulse duration of 250 ns are generated by an arbitrary waveform generator. The interval of the frequency sweep pulse sequence is 30 μs, the maximum repetition frequency is 18.2 kHz, and the average is 64 times. Double-coated single-mode fiber (SMF) is used as the sensing fiber to enhance the pressure sensitivity of Brillouin frequency shift (BFS), which the outer coating diameter is 3000 μm. The BFS pressure sensitivity of -3.32 MHz/MPa is achieved in the pressure range of 0-24 MPa, which is about 4.5 times that of SMF. The measurement time of the proposed optical fiber pressure sensing system is only 3.52 ms. Furthermore, the dynamic pressure measurement experiment is carried out, and the continuous measurement of the dynamic range of 6-0 MPa is achieved, and the dynamic distributed pressure measurement ability of the sensing system is verified.
Multichannel-Fiber Ringdown Sensor Based on Time-Division Multiplexing

Gaoming Li,Yishen Qiu,Shuqiang Chen,Shou Liu,Zhiyun Huang

DOI: https://doi.org/10.1364/ol.33.003022

2008-01-01

Abstract:A multichannel-fiber ringdown sensor based on the principle of time-division multiplexing is described. The purpose of multiplexing is to obtain the information of one or more fiber ringdown sensor heads simultaneously under the premise of cost neutrality. To illustrate the principle, we study the typical dual-channel fiber ringdown force sensor in our experiment. It shows that the pressures at two different points can be measured simultaneously. In addition, we find by measurement that our sensors have good linear responses above the response threshold of the applied force.
A hybrid fiber-optic sensing system for down-hole pressure and distributed temperature measurements

Ke Chen,Xinlei Zhou,Bokai Yang,Wei Peng,Qingxu Yu

DOI: https://doi.org/10.1016/j.optlastec.2015.04.001

2015-10-01

Abstract:A hybrid fiber-optic sensing technique, combining the extrinsic Fabry–Perot interferometer (EFPI) based pressure sensor with the incoherent optical frequency domain reflectometry (IOFDR) based distributed temperature sensor (DTS), is presented for down-hole measurements. By using a laser diode as the common light source, a highly integrated hybrid EFPI/DTS sensing system has been developed with a single fiber. With the injection current of the laser diode below lasing threshold, the broadband spontaneous emission light is used for EFPI based pressure sensing; while with the injection current above the threshold, the stimulated emission light is used for Raman based distributed temperature sensing. There is no overlap between the spectral range of the reflected light from the EFPI sensor and the spectral range of the Raman scattered light. Pressure and distributed temperature can thus be measured by using wavelength-division multiplexing (WDM) technology. Experimental results show that both the pressure and the distributed temperature are measured with little interference. Furthermore, the pressure measurement can be compensated by the measured temperature values.

optics,physics, applied
Multimode fiber tip Fabry-Perot cavity for highly sensitive pressure measurement

W. P. Chen,D. N. Wang,Ben Xu,C. L. Zhao,H. F. Chen

DOI: https://doi.org/10.1038/s41598-017-00300-x

IF: 4.6

2017-01-01

Scientific Reports

Abstract:We demonstrate an optical Fabry-Perot interferometer fiber tip sensor based on an etched end of multimode fiber filled with ultraviolet adhesive. The fiber device is miniature (with diameter of less than 60 μm), robust and low cost, in a convenient reflection mode of operation, and has a very high gas pressure sensitivity of −40.94 nm/MPa, a large temperature sensitivity of 213 pm/°C within the range from 55 to 85 °C, and a relatively low temperature cross-sensitivity of 5.2 kPa/°C. This device has a high potential in monitoring environment of high pressure.
High Pressure Sensor Based on Photonic Crystal Fiber for Downhole Application

H. Y. Fu,Chuang Wu,M. L. V. Tse,Lin Zhang,Kei-Chun Davis Cheng,H. Y. Tam,Bai-Ou Guan,C. Lu

DOI: https://doi.org/10.1364/ao.49.002639

IF: 1.9

2010-01-01

Applied Optics

Abstract:We demonstrate a polarization-maintaining (PM) photonic crystal fiber (PCF) based Sagnac interferometer for downhole high pressure sensing application. The PM PCF serves as a direct pressure sensing probe. The sensor is transducer free and thus fundamentally enhances its long-term sensing stability. In addition, the PM PCF can be coiled into a small diameter to fulfill the compact size requirement of downhole application. A theoretical study of its loss and birefringence changes with different coiling diameters has been carried out. This bend-insensitive property of the fiber provides ease for sensor design and benefits practical application. The pressure sensitivities of the proposed sensor are 4.21 and 3: 24 nm/MPa at similar to 1320 and similar to 1550 nm, respectively. High pressure measurement up to 20 MPa was achieved with our experiment. It shows both good linearity in response to applied pressure and good repeatability within the entire measurement range. The proposed pressure sensor exhibits low temperature cross sensitivity and high temperature sustainability. It functions well without any measurable degradation effects on sensitivity or linearity at a temperature as high as 293 degrees C. These characteristics make it a potentially ideal candidate for downhole pressure sensing. (C) 2010 Optical Society of America

Multimode Fiber Loop Ring Down Spectroscopy for Pressure Measurement

Multimode Fiber Ring‐down Pressure Sensor

Strain Measurement by Fiber-Loop Ring-Down Spectroscopy and Fiber Mode Converter

Fiber Mode Converter Incorporated Fiber Ring-Down Strain Sensor

&Lt;title&gt;distributed Optical Fiber Pressure Sensor&lt;/title&gt;

Dual-Parameter Active Fibre Sensor Based On Modal Interference In Few-Mode Fibres

Four-Channel Fiber Loop Ring-Down Pressure Sensor with Temperature Compensation Based on Neural Networks

Fiber Optic Pressure Sensor Based on Polarization-Maintaining Photonic Crystal Fiber for Downhole Application

Large dynamic range pressure sensor based on two semicircle-holes microstructured fiber

Research on Fiber Grating Sensing to Fiber Loop Ringdown

High sensitivity pressure sensor based on a simple SPS fiber loop mirror

Sensitivity-Enhanced Fiber-Optic Sensor in a Microwave Photonics Fiber Loop Ringdown System

Wide-range Optical Sensors Based on a Single Ring Resonator with Polarization Multiplexing

Simultaneous Measurement of Force and Temperature by a Multi-Position Fiber Loop Ringdown Sensor Array

Dual-Channel Fiber Ring Down Force Sensor

Diaphragm-Structured Fiber-Optic Pressure Sensors for Oil Downhole Applications

Dynamic Distributed Brillouin Optical Fiber Pressure Sensor

Multichannel-Fiber Ringdown Sensor Based on Time-Division Multiplexing

A hybrid fiber-optic sensing system for down-hole pressure and distributed temperature measurements

Multimode fiber tip Fabry-Perot cavity for highly sensitive pressure measurement

High Pressure Sensor Based on Photonic Crystal Fiber for Downhole Application

&Lt;title>distributed Optical Fiber Pressure Sensor</title>