Abstract:We report here our results on the investigation of the chain dynamics of poly(acrylic acid) in aqueous solution. The concentration of poly(acrylic acid) was approximately 3.8×10 −4 mol/L, two orders of magnitude higher than that reported in the literature. The pH value of the solution was 3.9, and the hydrogen bonds between the intrinsic and ionized carboxylic acid groups formed dynamic networks, which captured aggregation-induced emission-active molecules (a tetra-quaternary ammonium modified tetraphenylethene derivative) inside the polymer coils and induced fluorescence emission. The hydrogen bonds can be classified as intra- or intermolecular; both can be probed based on the emission change of the tetra-quaternary ammonium modified tetraphenylethene probes. The effects of different external stimuli on the polymer chain dynamics were investigated using different metal cations (including Na + , Li + , Zn 2+ , Ni 2+ , Ca 2+ , and Co 2+ ), different cation concentrations (1×10 −6 to 4×10 −4 mol/L), different poly(acrylic acid) molecular weights (5, 240, and 450 kDa), and different copolymers. The experimental results indicate that the long poly(acrylic acid) chains (high molecular weight) tend to form dense globular coils and exclude the probe molecules outside, which are robust and unsusceptible to water-soluble metal cations. However, the shorter poly(acrylic acid) chains tend to form intermolecular hydrogen bonds, which are helpful in capturing more probe molecules inside the networks, thus inducing stronger emission. Because of the dual functions of forming hydrogen bonds with carboxylic groups and acting as an acceptor of protons from the carboxylic acid group to form cationic species, copolymerization with acrylate amide [poly(acrylic acid)- co -poly(acrylamide)] can greatly affect the chain dynamics of poly(acrylic acid) segments, which is reflected by the drastically decreased emission intensity from the fluorescent probes.

Study on Cellular Structure of Acrylonitrile/ Methacylic Acid Copolymer Foam Plastic

Effect of Melt Viscosity on the Cell Morphology and Properties of Poly(lactic Acid) Foams

Influence of Small Amount of Co-Monomers on Acrylonitrile Polymerization in Dimethylformamide (DMF) Solution

High-Strength and Shape-Memory Epoxy Cellular Material with Wood-Like Architecture

Factors affecting the microstructure of a fine ceramic foam

Research on Microcellular ABS Foam by Compression Molding

Temperature and Ph Response, and Swelling Behavior of Porous Acrylonitrile-Acrylic Acid Copolymer Hydrogels

Preparation, Characterization, and Mechanical Properties of Microcellular Poly(Aryl Ether Ketone) Foams

Copolymer Membrane Preparation of 2-(N,n-dimethyl Aminoethylme) and Acrylonitrile and Its Gas Permeance Performance

STUDY ON THE FOAMABILITY OF VINYLIDENE CHLORIDE COPOLYMER PARTICLES

Reflectance According to Cell Size, Foaming Ratio and Refractive Index of Microcellular Foamed Amorphous Polymer

Aramid fiber reinforced EPDM microcellular foams: Influence of the aramid fiber content on rheological behavior, mechanical properties, thermal properties, and cellular structure

Probing the effects of external species on poly(acrylate acid) chain dynamics by using cationic AIE-active fluorophore

Preparation of Porous Copolymers of Acrylonitrile with Methyl Acrylate by Suspended Emulsion Polymerization

The Molecular Structure Control of Butyl Methacrylate/acrylamide (Co)polymers

Tuning cellular structure in a previously developed microcellular acrylonitrile butadiene styrene/thermoplastic polyurethane blend foams

Effect of the Aromatic Amine Curing Agent Structure on Properties of Epoxy Resin-Based Syntactic Foams

Regulating cell morphology of poly (lactic acid) foams from microcellular to nanocellular by crystal nucleating agent

Microcellular Injection Molded Wood Fiber-PP Composites: Part I - Effect of Chemical Foaming Agent Content on Cell Morphology and Physico-mechanical Properties

High molecular weight of poly(acrylonitrile-co-3-aminocarbonyl-3-butenoic acid methyl ester) used as carbon fiber precursor: preparation and stabilization

The Cellular Structure and Mechanical Properties of Polypropylene/Nano-CaCO3/Ethylene-propylene-diene-monomer Composites Prepared by an In-Mold-Decoration/Microcellular-Injection-Molding Process