Abstract:To optimise the benefits of the deep-rolling process in the service life context of treated components, the process application must be investigated. In addition to the reduction in surface roughness and near-surface material strengthening, compressive residual stresses are introduced, which are primarily responsible for the increase in service life for components, especially in the case of high-strength steel materials. A numerical parameter sensitivity analysis is performed in order to investigate the introduced residual stresses in detail. For this purpose, a validated deep-rolling simulation model is used, which replicates the deep rolling of a railway axle made of the high-strength steel material 34CrNiMo6. The model is based on an elastic-plastic Chaboche material model parameterised on uniaxial tensile and LCF test results and validated with residual stress measurements. Using this model as a basis, the effect of the main process parameters deep-rolling force, feed rate, friction coefficient, number of overruns, tool geometry, and shaft geometry on the resulting residual stress state are investigated. The results reveal that the deep-rolling force has the most significant influence on the introduced residual stress state and should therefore be highlighted. In the case of applying a deep-rolling force of more than 10 kN, maximum compressive residual stresses of around − 1000 MPa are introduced, and a strong saturating behaviour is shown. Maximum compensating tensile residual stresses of + 100 MPa occur below the surface. The main influence of the deep-rolling force is the effective depth achieved, which is determined by the depth of the zero crossing. This varies from 1 mm with an applied force of 2 kN to more than 3.5 mm with 20 kN. Furthermore, the results are analysed to conclude suggestions for the process's applicability, and a proposal for an optimised deep-rolling treatment is presented. There multiple deep rolling with decreased deep-rolling forces is used to achieve a comparably optimised residual stress state. In summary, with the presented results, a contribution to a deeper understanding of the deep-rolling process can be achieved; the influence of the most important process parameters on the residual stress in-depth profiles is established; an optimisation proposal is presented; and correlations are found. Thus, the base work for further fatigue strength assessments and the optimisation of the deep-rolling process regarding the increase of service is laid.

Influence of Roll Smoothing on the Initial Residual Stress Fields of 10ni5crmov Steel Heavy Gauge Plates

Evolution of Residual Stress Based on Curvature Coupling in Multi-Roll Levelling

Study on Machining Deformation of Aircraft Monolithic Component by FEM and Experiment

The Influence of Warm Rolling Reduction on Microstructure Evolution, Tensile Deformation Mechanism and Mechanical Properties of an Fe-30Mn-4Si-2Al TRIP/TWIP Steel

Analysis and Simulation of Machining Deformation Resulting from Residual Stress

The Causes and Control of Longitudinal Edge Cracks of the Plate

Numerical parameter sensitivity analysis of residual stresses induced by deep rolling for a 34CrNiMo6 steel railway axle

Effects of Rolling Speed and Reduction on Rolling Simulation Results of Monolithic Fuel Plates

Evolution of Surface Crack on Slab During Rough Rolling Using Thermal-Mechanical FEM

Influence of Gradual Stress Relieving on the Microstructure, Texture Development, Grain Structure and Orientation of the Hot-Rolled Ti6Al4V-5Cu Alloy.

Research on the Temperature and Thermal Stress of the Roll Quenching Process of Thin Plates

Numerical Simulation of Quenching and Pre-Stretching Residual Stress in 7085 Aluminum Alloy Plate

Static softening behavior of 316L stainless steel under flexible rolling process

Simulation of Residual Stress of V-Notch Specimen Treated by Ultrasonic Rolling

Investigation on the Evolution of Residual Stress in Ultrasonic Surface Rolling Treatment-Processed 18CrNiMo7-6 Alloy Steel

FEM simulation of thermo-mechanical stress and thermal fatigue life assessment of high-speed steel work rolls during hot strip rolling process

Multi-pass Medium Plate Rolling Processes Using Thermo-mechanical FE Analysis

Investigation into the Rolling Process of 20CrNiMo/Incoloy 825 Composite Materials

The central strain analytical modeling and analysis for the plate rolling process

Analysis of the Influence of Contact Stress on the Fatigue of AD180 High-Carbon Semi-Steel Roll

Experimental study on the evolution law of residual stress in the fatigue process of inductively quenched 42CrMo steel