Abstract:Bismuth telluride (Bi2Te3)-based alloys are widely used for thermoelectric cooling and power generation at low temperatures, and they are the only commercially available materials for thermoelectric applications below 500 K. The rhombohedral unit cell with a large c/a lattice constant ratio consisting of - Te-Bi-Te-Bi-Te- stacked layers inevitably brings about a large anisotropy in transport properties, which is why texturing is very important in polycrystalline Bi2Te3</sub alloys for maximum performance. In this report, p and n-type polycrystalline Bi2Te3</sub alloys were synthesized and hot-deformed to investigate the effects of texturing on thermoelectric properties. Hot deformation (HD) induces the strong alignment of (001) orientations along the compression direction, and a remarkable increase in the orientation factor F of (001) orientations is observed after HD in both p and n-type materials. All of the hot-deformed polycrystalline samples showed increased electrical conductivity (σ), power factor (PF), and thermal conductivity (k) in the in-plane (IP) direction, and vice versa in the out-of-plane (OOP) direction, which makes the IP direction of the hot-deformed bodies more favorable for module fabrication in terms of power factor, for both p and n-type Bi2Te3</sub-based alloys. However, due to the different degree of anisotropy of k and σ, the figures of merit (zT) were maximized in the OOP direction in the p-type materials after HD, whereas the zTs of the n-type materials were higher in the IP direction. This occurs because the anisotropy factor of electron conduction is higher than that of hole conduction, which more than offsets the advantage of the smaller k in the c-direction of n-type Bi2Te3</sub. The maximum zT of 1.33 (OOP) and 0.90 (IP) were obtained after HD from the p and n-type Bi2Te3 alloys, respectively, which were 9.3% and 18.4% higher than those of as-sintered materials.

Mechanical and Thermoelectric Performance of p-type Bi-Sb-Te Prepared by Hot Pressing

Ultrasonic-assisted Hot Pressing of Bi2Te3-based Thermoelectric Materials

Microstructure and thermoelectric properties of porous Bi 2 Te 2.85 Se 0.15 bulk materials fabricated by semisolid powder processing

Microstructure and thermoelectric performance evaluation of p-type (Bi, Sb)2Te3 materials synthesized using mechanical alloying and spark plasma sintering process

Thermoelectric and thermomechanical properties of the hot pressed polycrystalline Bi0.5Sb1.5Te3 alloys

High Thermoelectric Performance Bismuth Telluride Prepared by Cold Pressing and Annealing Facilitating Large Scale Application

High-Performance p-Type Bi 2 Te 3 -Based Thermoelectric Materials Enabled via Regulating Bi-Te Ratio

High thermoelectric and mechanical performance in strong-textured n-type Bi2Te2.7Se0.3 by temperature gradient method

Critical Role of Tellurium Self-Compensation in Enhancing the Thermoelectric Performance of P-Type Bi0.4Sb1.6Te3 Alloy

Rare Earth Ytterbium Enhanced Thermoelectric Properties of P-Type Bi0.5Sb1.5Te3

Process Controls for Bi 2 Te 3 -Sb 2 Te 3 Prepared by Mechanical Alloying and Hot Pressing

High thermoelectric performance achieved in Bi0.4Sb1.6Te3 films with high (00l) orientation via magnetron sputtering

Texture Development and Grain Alignment of Hot‐Pressed Tetradymite Bi 0.48 Sb 1.52 Te 3 Via Powder Molding

High Thermoelectric Performance of p-Type Bi0.4Sb1.6Te3+ x Synthesized by Plasma-Assisted Ball Milling

Thermoelectric properties of hydrothermally synthesized and hot pressed n-type Bi2Te3 alloys with different contents of Te

Thermoelectric properties and thermal stability of Bi-doped PbTe single crystal

Enhanced Thermoelectric Properties Obtained by Compositional Optimization in P -Type Bi X Sb 2− X Te 3 Fabricated by Mechanical Alloying and Spark Plasma Sintering

Unraveling electronic origins for boosting thermoelectric performance of p-type (Bi,Sb) 2 Te 3

Analysis of Thermoelectric Properties of Hot-deformed Bismuth Telluride Sintered Materials

Tunable Electrical Conductivity and Simultaneously Enhanced Thermoelectric and Mechanical Properties in n-type Bi<sub>2</sub>Te<sub>3</sub>

Thermoelectric Properties of Rapid Hot Pressed Polycrystalline Ag1−xPb18SbTe20 Synthesized from Doping PbTe Nanocrystals