Abstract:Amorphous Fe73.5-xCoxSi13.5B9Cu1Nb3（x=10,30,50） ribbons were prepared by the single copper wheel melt spinning technique in the air atmosphere.The nanocrystallization kinetics of amorphous ribbons was investigated by differential scanning calorimetry（DSC）.The apparent activation energies of amorphous ribbons were calculated by using Kissinger and Ozawa methods.It was found that the activation energies of the first crystallization reduce and those of the second crystallization rise with increasing Co content.The local Avrami parameter m for primary crystallization was calculated using Johnson-Mehl-Avrami（JMA） model.The values of the Avrami parameter showed that the primary crystallization mechanism of amorphous ribbons varied at different stages.In the initial stage,the crystallization mechanism was bulk crystallization with three dimensional nucleation and grain growth controlled by diffusion.In the following stage,it was surface crystallization with one dimensional nucleation and grain growth at a near zero nucleation rate.The variation of soft magnetic properties of nanocrystalline Fe63.5Co10Si13.5B9Cu1Nb3 powder cores as a function of milling time has been investigated.It was found that the effective permeability of the cores shows high frequency stability and decreases with increasing milling time.The quality factor increases with increasing frequency in the lower frequency range,reaches a maximum at the frequency of 80 kHz,and then decreases gradually with increasing frequency.

Separation of Supersaturation Solid Solution and Effects on Resistivity in Melt-Spun Cu100-xCrx Ribbons

Liquid and Solid Phase Separation During Melt Spinning and Annealing in Melt-Spun Cu–Cr Ribbons

MICROSTRUCTURE OF AS-MELT SPUN Al-Cu-Mg-Fe-Ni ALLOY AND ITS VARIATION IN CONTINUOUS HEAT TREATMENT

Microstructures of Melt-Spun Cu100−x–Crx (x=3.4–25) Ribbons

Effects of Zr addition on the liquid phase separation and the microstructures of Cu-Cr ribbons with 18-22 at.% Cr

Effects Of Ti Addition On Microstructures Of Melt-Spun Cucr Ribbons

Effect of titanium additives on the microstructure of melt-spun CuCr ribbons

Effects of Melt-Spinning on Refining of Microstructures for CuCr25 Alloy and Their Chopping Currents

Effect of Ni Addition on the Microstructures of Melt-Spun CuCr Ribbons

Amorphous-crystalline Dual-Layer Structures Resulting from Metastable Liquid Phase Separation In(fe 50 Co 25 B 15 Si 10 ) 80 Cu 20 Melt-Spun Ribbons

Crystallization Kinetics of Co-Finemet Amorphous Alloys and Magnetic Properties of Nanocrystalline Powder Cores

Effects of Ti Addition on the Liquid-Phase Separation of Cu 71 Cr 29 Alloy During Rapid Cooling

Effect of Cu Contents on Magnetic Properties of the Sm(Co0.74CuxFe0.1Zr0.04)8

The Microstructure and Mechanical Properties of the As-Spun and Annealed ZrCu Based Ribbons

The Crystallization Kinetics Study of Finemet-Co Amorphous Alloys

The effect of annealing temperatures on the phase constitutes, thermal properties and corrosion behaviors of Ti-Ni-Zr-Cu high entropy alloy thin ribbons

The Solidification of Cucr Alloys under Various Cooling Rates

Microstructure and Magnetic Properties of Rapidly Quenched Sm2(Fe,Al,Zr)17C1.5 Ribbons with Zr Additions

Effects of annealing and magnetic field on the structure and magnetic properties of Fe-Cr-Co alloy-doped Sm(Co0.9Cu0.1)5 ribbons

Compositions, Magnetic Properties and GMR Performances of Melt-Spun Cu–Co–Ni Ribbons

Effect of solid solution process on the structure and properties of Cu-Cr-Mg alloy in the aging state