Abstract:Laser machining has been emerging as a powerful alternative for cutting thin metal substrates. In this study, the application of pulsed laser cutting of a thin nonoriented silicon steel, with a thickness of 0.1 mm, was studied. The four processing parameters considered were laser power, cutting speed, pulse repetition rate, and processing environment. The two outputs to be measured were the extent of heat-affected zone (HAZ) and deviation of magnetic flux density (MFD) from initial value. Each input was designed with three levels and the three processing environments were air, deionized water, and sodium chloride solution. Based on the experimental design of the L27 Taguchi method, 27 parameter sets out of the total of 81 sets were used for the experiment. Results show that HAZ and MFD were negatively correlated. Compared with processing in air, cutting in the liquid could effectively reduce the HAZ. In the 27 experimental cases, the achieved minimum HAZ was 34.5 μm that corresponded to retaining 99% of initial MFD. The importance of the input was analyzed by the random forest method. The most and second significant parameters were laser power and environmental condition and their importance levels were 50.82% and 40.99%, respectively. Four artificial intelligence (AI) prediction models, full quadratic multiple regression analysis, artificial neural network, random forest, and extreme learning machine (ELM), were established based on randomly selecting 80% of the 27 data sets for training and the remaining 20% for testing. Model verification was executed by arbitrarily taking 10 additional new predictive parameter sets, from the remaining 54 parameter sets, for experiments. After comparing the predicting and experimental results, ELM model was found to have the best forecast performance. Thus, it was chosen as the target model for output optimization by the genetic algorithm method (GA). Through implementing the predicted optimal processing parameters from the resulting ELM-GA algorithm for the confirmation experiment, the obtained MFD and HAZ were 1.639 T and 30.41 μm, respectively, which were very close to that of the predicted optimal outputs, 1.640 T for MFD and 29.90 μm for HAZ.

Synthetic Evaluation and Neural-Network Prediction of Laser Cutting Quality

In-process measurement of grinding workpiece surface quality based on neural network

Study of synthesis identification in the cutting process with a fuzzy neural network

Modeling and process parameter optimization of laser cutting based on artificial neural network and intelligent optimization algorithm

Predicting and Enhancing the Multiple Output Qualities in Curved Laser Cutting of Thin Electrical Steel Sheets Using an Artificial Intelligence Approach

Neural networks for predicting kerf characteristics of CO2 laser-machined FFF PLA/WF plates

A Deep Learning Method for Material Performance Recognition in Laser Additive Manufacturing

Multi-objective optimization of fiber laser cutting quality characteristics of glass fiber reinforced plastic (GFRP) materials

Study on Relationship Between Radiation and Quality for Laser Cutting

Experimental Research of Laser Cutting 1cr17mn6ni5n Steel Plates

Early Event Detection in a Deep-Learning Driven Quality Prediction Model for Ultrasonic Welding

Prediction of Femtosecond Laser Etching Parameters Based on a Backpropagation Neural Network with Grey Wolf Optimization Algorithm

Prediction of quality characteristics of micro-channels by deep learning algorithm during laser transmission ablation of PMMA

Application of RBF Neural Network in Three Dimensional Laser Cutting

FUZZY EXPERT SYSTEM FOR PREDICTION OF KERF QUALITIES IN PULSED LASER CUTTING OF TITANIUM ALLOY SHEET

Artificial intelligence-based modeling and optimization of heat-affected zone and magnetic property in pulsed laser cutting of thin nonoriented silicon steel

Experimental Investigation of Industrial Laser Cutting: The Effect of the Material Selection and the Process Parameters on the Kerf Quality

Neural network-based prediction for surface characteristics in CO2 laser micro-milling of glass fiber reinforced plastic composite

Automated quality evaluation for laser cutting in lithium metal battery production using an instance segmentation convolutional neural network

Depth Accurate Prediction and Kerf Quality Improvement of CFRP Through-Hole Laser Cutting via Acoustic Emission Nondestructive Monitoring Technology

Prediction and optimization of joint quality in laser transmission welding using serial artificial neural networks and their integration with Markov decision process