Abstract:The interaction between nanosecond laser and glass is complicated, and defects such as micro-cracks and fractures are prone to be generated during laser scribing. Acoustic emission (AE) technique is applied in this paper to monitor laser scribing of float glass. Strong consistency between AE signals and width of laser ablation area is found. With laser power increasing from 11.2 to 26.9 W, root mean square (RMS) values increase from 0.160 to 0.634 V, and width of heat affected zone (HAZ) increase from 12.396 to 53.711 μm\documentclass[12pt]{minimal}\usepackage{amsmath}\usepackage{wasysym}\usepackage{amsfonts}\usepackage{amssymb}\usepackage{amsbsy}\usepackage{mathrsfs}\usepackage{upgreek}\setlength{\oddsidemargin}{-69pt}\begin{document}$${\upmu }\text{m}$$\end{document}. Correlation between AE signals and laser scribing quality is investigated by characteristic analysis. When scanning speed is kept constant (200 mm/s) and laser power is gradually increasing from 11.2 to 24.2 W, RMS values and MARSE are increasing (0.3–1.2 V, 600–1500 correspondingly), and scribing quality is declining continuously (WCWG\documentclass[12pt]{minimal}\usepackage{amsmath}\usepackage{wasysym}\usepackage{amsfonts}\usepackage{amssymb}\usepackage{amsbsy}\usepackage{mathrsfs}\usepackage{upgreek}\setlength{\oddsidemargin}{-69pt}\begin{document}$$\frac{{W}_{C}}{{W}_{G}}$$\end{document} increase from 0 to 0.343). Time-frequency spectrum analysis by CWT could be applied in defects diagnosis. Three prominent frequency bands contents (150 ~ 180 kHz, 200 ~ 250 kHz, and 280 ~ 320 kHz) were generated during laser scribing process. Higher frequency bands contents (200 ~ 250 kHz, and 280 ~ 320 kHz) are demonstrated to reflect defects by analyzing distribution characteristic of frequency contents. Intensity of higher frequency compositions is vigorous (≥ 0.5) when there are defects, while less than 0.5 with no defects.

Study on Relationship Between Radiation and Quality for Laser Cutting

Quality detection and control during laser cutting progress with coaxial visual monitoring

Effect of Variable Cross-Section Rod on Laser-Induced Surface Acoustic Waves.

Quality Monitoring for CO_2 Laser Cutting with Visual Sensing System (Ⅲ) Coaxial Visual Detection of Surface Roughness for Laser Cutting

Quality Monitoring for CO2 Laser Cutting with Visual Sensing System (Ⅰ) Defect Detection with Coaxial Visual Sensing System

Depth Accurate Prediction and Kerf Quality Improvement of CFRP Through-Hole Laser Cutting via Acoustic Emission Nondestructive Monitoring Technology

Synthetic Evaluation and Neural-Network Prediction of Laser Cutting Quality

Acoustic emission monitoring and heat-affected zone evaluation of CFRP laser cutting

Analysis of the Effects on Ultra-Short Laser Pulse Beam Quality Caused by Errors in Optical Systems

Evaluation and classification of CFRP kerf width by acoustic emission in nanosecond laser cutting

Analysis Of Nonlinear Self-Focusing Phenomenon In High-Power Laser System Based On Ray-Tracing

A comprehensive review of studying the influence of laser cutting parameters on surface and kerf quality of metals

Relationship Between Weld Quality and Optical Emissions in Underwater Nd : Yag Laser Welding

Laser Cutting Wood Test and Influencing Factors of Processing Quality

Experimental Research of Laser Cutting 1cr17mn6ni5n Steel Plates

Study of Evaluating Nearfield Beam Quality of the High Power Laser Beams

Research on Correlation Between Weld Concavity and Weld Process Parameters in Tailored Blank Laser Welding

Laser Damage Performance Study of Fundamental Frequency Dielectric Film Optical Elements

A novel monitoring method of nanosecond laser scribing float glass with acoustic emission

532 nm Nanosecond laser cutting solar float glass: Surface quality evaluation with different laser spot positions in field lens

A study on spectral characterization and quality detection of direct metal deposition process based on spectral diagnosis