Abstract:The interaction between nanosecond laser and glass is complicated, and defects such as micro-cracks and fractures are prone to be generated during laser scribing. Acoustic emission (AE) technique is applied in this paper to monitor laser scribing of float glass. Strong consistency between AE signals and width of laser ablation area is found. With laser power increasing from 11.2 to 26.9 W, root mean square (RMS) values increase from 0.160 to 0.634 V, and width of heat affected zone (HAZ) increase from 12.396 to 53.711 μm\documentclass[12pt]{minimal}\usepackage{amsmath}\usepackage{wasysym}\usepackage{amsfonts}\usepackage{amssymb}\usepackage{amsbsy}\usepackage{mathrsfs}\usepackage{upgreek}\setlength{\oddsidemargin}{-69pt}\begin{document}$${\upmu }\text{m}$$\end{document}. Correlation between AE signals and laser scribing quality is investigated by characteristic analysis. When scanning speed is kept constant (200 mm/s) and laser power is gradually increasing from 11.2 to 24.2 W, RMS values and MARSE are increasing (0.3–1.2 V, 600–1500 correspondingly), and scribing quality is declining continuously (WCWG\documentclass[12pt]{minimal}\usepackage{amsmath}\usepackage{wasysym}\usepackage{amsfonts}\usepackage{amssymb}\usepackage{amsbsy}\usepackage{mathrsfs}\usepackage{upgreek}\setlength{\oddsidemargin}{-69pt}\begin{document}$$\frac{{W}_{C}}{{W}_{G}}$$\end{document} increase from 0 to 0.343). Time-frequency spectrum analysis by CWT could be applied in defects diagnosis. Three prominent frequency bands contents (150 ~ 180 kHz, 200 ~ 250 kHz, and 280 ~ 320 kHz) were generated during laser scribing process. Higher frequency bands contents (200 ~ 250 kHz, and 280 ~ 320 kHz) are demonstrated to reflect defects by analyzing distribution characteristic of frequency contents. Intensity of higher frequency compositions is vigorous (≥ 0.5) when there are defects, while less than 0.5 with no defects.

Evaluation and classification of CFRP kerf width by acoustic emission in nanosecond laser cutting

Acoustic emission monitoring and heat-affected zone evaluation of CFRP laser cutting

Depth Accurate Prediction and Kerf Quality Improvement of CFRP Through-Hole Laser Cutting via Acoustic Emission Nondestructive Monitoring Technology

Ultrasonic Detection Method of Micro Defects in Thick-Section CFRP

The Ultrasonic Evaluation Method for the Porosity of Variable-Thickness Curved CFRP Workpiece: Using a Numerical Wavelet Transform

Variable Frequency Selective Structure (cfrp/cu/cfrp) Micro Blind Hole Laser High-Quality Drilling Method Guided by Acoustic Emission Technology

Experimental Study on Carbon Fiber-Reinforced Composites Cutting with Nanosecond Laser

Study on the CFRP nanosecond laser cutting damage and efficiency by aspiration system assisted method

Surface defect and chatter monitoring in robotic drilling CFRP composites using acoustic emission technique

Delamination Analysis of Carbon Fiber/Epoxy Composite Laminates under Different Loading Rates Using Acoustic Emission

A New Quantitative Acoustic Emission Model for Damage Characterization of Composite Laminates Using Original Waveforms

A novel monitoring method of nanosecond laser scribing float glass with acoustic emission

Experimental Evaluation of Cutting Quality of Carbon Fibre Reinforced Polymer with Pulsed Laser

Investigating the Technology of UV Nanosecond Laser Milling for Cutting CFRP Laminates.

Study on UV Laser Cutting Carbon Fibre Reinforced Composites

Experimental Study on Picosecond Laser Cutting AFRP Composites

Online vibration monitoring using laser vibrometer and acoustic emission techniques in robotic milling CFRP composites

Experimental Analysis on Delamination Damage by Acoustic Emission in High Speed Drilling of Carbon Fiber Reinforced Plastics

Water jet guided nanosecond laser cutting of CFRP

Effect of scanning spacing on the efficiency of CFRP hole-cutting with multi-pass scanning strategy by nanosecond laser

Investigation on heat transfer and ablation mechanism of CFRP by different laser scanning directions