Abstract:Introduction: To investigate the ablation efficiency of super-pulse thulium fiber laser (SPTFL) with different laser settings and fiber usage. Materials and Methods: SPTFL machine was attached with different fibers. Artificial stones were fixed in water, whereas laser fiber was driven on a platform for ablation. Pulse energy, frequency, fiber-moving speed, fiber-to-stone distance, and fiber size were adjusted in each trial. The cross-sectional area of craters on the lateral stone surface was measured for comparison of ablation rate, combined with fiber-moving speed. Results: There was a trend that the ablation rate increased as pulse energy or frequency increased. When pulse energy was set as 0.2 J and frequency was increased from 50 to 150 Hz, the cross-sectional area of the crater was enlarged from 0.21 to 0.37 mm(2) (p < 0.05); when the frequency was set as 100 Hz and pulse energy was increased from 0.1 to 0.3 J, the crater was enlarged from 0.10 to 0.45 mm(2) (p < 0.05). Furthermore, energy demonstrated greater impact on ablation rate and the crater was enlarged from 0.20 mm(2) in the 0.1 J x 300 Hz group to 0.44 mm(2) in the 0.3 J x 100 Hz group (p < 0.05). Then fiber was set at different moving speeds with the same laser setting; the ablation rate of 3 mm/second group was 3.64 times higher than 0.5 mm/second group (p < 0.05). Ablation diminished as fiber-to-stone distance grew. A 200 mu m fiber produced thinner and deeper fissure than 272 and 550 mu m fibers, and the ablation rate was the highest for the 200 mu m fiber. Conclusion: Pulse energy is a more important factor in influencing ablation efficiency compared with frequency. Closer fiber-to-stone distance, faster fiber movement, and smaller fiber size increase ablation efficiency.

Experimental Study on Picosecond Laser Cutting AFRP Composites

Experimental Study on Carbon Fiber-Reinforced Composites Cutting with Nanosecond Laser

Investigations on 355 nm picosecond laser machining of carbon fiber reinforced polymer composites

Ablation Efficiency of a Novel Thulium Fiber Laser: an in Vitro Study on Laser Setting and Fiber Usage.

Investigating the Technology of UV Nanosecond Laser Milling for Cutting CFRP Laminates.

Experimental probe into the femtosecond laser ablation thresholds in carbon fiber reinforced polymer and assessment of the measurement theories

Experimental study on CFRP drilling with the picosecond laser "double rotation" cutting technique

Effect of scanning spacing on the efficiency of CFRP hole-cutting with multi-pass scanning strategy by nanosecond laser

Investigation on heat transfer and ablation mechanism of CFRP by different laser scanning directions

Experimental study on the sidewall quality of femtosecond laser drilling CFRP

Analysis and optimization of the heat affected zone of CFRP by femtosecond laser processing

Femtosecond Laser Drilling of Cylindrical Holes for Carbon Fiber-Reinforced Polymer (CFRP) Composites

Study on anisotropic heat transfer and thermal damage in nanosecond pulsed laser processing of CFRP

Investigation of Heat Accumulation in Femtosecond Laser Drilling of Carbon Fiber-Reinforced Polymer

Experimental Investigation on Ablation Behaviors of CFRP Laminates in an Atmospheric Environment Irradiated by Continuous Wave Laser

Processing characteristics of C/C composites with nanosecond pulse laser

Acoustic emission monitoring and heat-affected zone evaluation of CFRP laser cutting

Dual-Method Characterization and Optimization of Drilling Parameters for Picosecond Laser Drilling Quality in CFRP

Hole Quality and Thermal Defects in Drilled CFRP by Nanosecond Pulsed Laser

Mechanism and Behavior of Laser Irradiation on Carbon Fiber Reinforced Polyetheretherketone (CF/PEEK) During the Laser-Assisted In-Situ Consolidation Additive Manufacturing Process

The ablation threshold and incubation effect in picosecond laser surface treatment of CFRP