Abstract:Wood-based composites are increasingly used in the industry not only because of the shortage of solid wood, but above all because of the better properties, such as high strength and aesthetic appearance compared to wood. Medium-density fiberboard (MDF) is a wood-based composite that is widely used in the furniture industry. In this work, an attempt was made to predict the surface roughness of the machined MDF in the milling process based on acceleration signals from an industrial piezoelectric sensor installed in the cutting zone. The surface roughness parameter Sq was adopted for the evaluation and measurement of surface roughness. The surface roughness prediction was performed using a radial basis function (RBF) artificial neural network (ANN) and a Takagi-Sugeno--Kang (TSK) fuzzy model with subtractive clustering. In the research, as inputs to the ANNs and fuzzy model, the kinematic parameters of the cutting process and selected measures of the acceleration signal were adopted. At the output, the values of the surface roughness parameter Sq were obtained. The results of the experiments show that the surface roughness is influenced not only by the kinematic parameters of the cutting, but also by the vibrations generated during the milling process. Therefore, by combining information on the cutting kinematics parameters and vibration, the accuracy of the surface roughness prediction in the milling process of MDF can be improved. The use of TSK fuzzy modelling based on the subtractive clustering method for integrating the information from many acceleration signal measurements in the examined range of cutting conditions meant the surface roughness was predicted with high accuracy and high reliability. With the help of two tested artificial intelligence tools, it is possible to estimate the surface roughness of the workpiece with only a small error. When using a radial neural network, the root mean square error for estimating the value of the Sq parameter was 0.379 μm, while the estimation error based on fuzzy logic was 0.198 μm. The surface of the sample made with the cutting parameters vc = 76 m/min and vf = 1200 mm/min is characterized by a less concentrated distribution of ordinate densities, compared to the surface of the sample cut with lower feed rates but at the same cutting speed. The most concentrated distribution of ordinate density (for the cutting speed vc = 76 m/min) is characterized by the surface, where the feed rate value was vf = 200 mm/min, with 90% of the material concentrated in the profile height of 28.2 μm. When using an RBF neural network, the RMSE of estimating the value of the Sq parameter was 0.379 μm, while the estimation error based on fuzzy logic was 0.198 μm.

Application of RBF Neural Network in Three Dimensional Laser Cutting

Shape sensing using neural network of radial basis function based on Fiber Bragg Grating

A memristive RBF neural network and its application in unsupervised medical image segmentation

A Novel Nonlinear Dynamic System Modeling Approach Using Radial Basis Function Neural Networks

Pre-evaluation on Surface Profile in Turning Process Based on Cutting Parameters

Training Radial Basis Function Classifiers with Gaussian Kernel Clustering and Fuzzy Decision Technique

Surface Profile Prediction and Analysis Applied to Turning Process

Synthetic Evaluation and Neural-Network Prediction of Laser Cutting Quality

Deep RBFNet: Point Cloud Feature Learning using Radial Basis Functions

Neural networks for predicting kerf characteristics of CO2 laser-machined FFF PLA/WF plates

Modeling the field of laser welding melt pool by RBFNN

RBF design method based on center clustering and PSO

The Growing Radial Basis Function (RBF) Neural Network and Its Applications.

Modeling and process parameter optimization of laser cutting based on artificial neural network and intelligent optimization algorithm

Pls Algorithm For Radial Basis Function Networks

Fault Diagnosis Based On Radial Basis Function Neural Network In Particleboard Glue Mixing & Dosing System

Deformation Forecast in Numerical Control Milling Based on Artificial Neural Networks

Dynamics modeling for the ultrasonic machining tool using a data-driven approach and a D-RBFNN

The Use of a Radial Basis Function Neural Network and Fuzzy Modelling in the Assessment of Surface Roughness in the MDF Milling Process

Predicting and Enhancing the Multiple Output Qualities in Curved Laser Cutting of Thin Electrical Steel Sheets Using an Artificial Intelligence Approach

Prediction of TC11 single-track geometry in laser metal deposition based on back propagation neural network and random forest