Abstract:Cu matrix composites have received increased attention in a wide industrial area because of their excellent mechanical properties and good electrical and thermal conductivity. However, the addition of general ceramic reinforcements often leads to a marked reduction in electrical conductivity for Cu matrix composites. In this study, the ZrB 2 -reinforced Cu composites have been developed to overcome this drawback since these metal borides possess relatively high electrical conductivity. The 5 wt.% ZrB 2 /Cu composites were prepared using hot-pressed sintering techniques at varying temperatures from 760 to 920°C. The influence of sintering temperature on the microstructure, relative density, and mechanical and electrical properties was examined. The results of the SEM observation show that ZrB 2 particles are seamlessly integrated into the Cu matrix for all ZrB 2 /Cu composites. The average grain size of the Cu matrix increases from 360 to 980 nm with the increase of the sintering temperature. The increase in sintering temperature also leads to the surface porosity decrease from 1.4 to 0.4%. The relative density and electric conductivity of the composites increase at the same time as the sintering temperature increases. However, microhardness increases and decreases, with a maximum value of 92 HV0.2 achieved at 840°C. The elastic modulus and nanohardness maps determined from the nanoindentation indicate that the reinforced ZrB 2 particles demonstrate the highest values for elastic modulus (340–500 GPa) and nanohardness (30–48 GPa). At the same time, the Cu matrix possesses a modulus of 100–200 GPa and nanohardness of about 10 GPa. TEM observation confirmed that the sintering temperature exhibits little influence on the interface reaction between ZrB 2 and Cu. Both sharp interface and interface with amorphous transition layer are observed. The variation of microhardness is mainly due to the strengthening of grain refinement and to the mismatch of the thermal expansion coefficients. The above results can provide further insights into the deeper understanding of the role of sintering temperature during hot-pressed sintering.

Effects of Sintering Method on Density and Microstructure of Particulate Reinforced Copper Matrix Composites

Sintering Densification of Cu/Al2O3p Nano-Composite Powders by Electroless Copper Plating

Effects of Process Parameters on Microstructure and Properties of TiC Reinforced Cu-Matrix Composites

Study of Hot-press Sintering Process of Nanometer Cu-Al_2O_3 Composite

Influence of sintering processes on the density of nano-AgSnO2 composites

Effect of the microstructure and properties of graphite/copper composites fabricated by microwave sintering

Effect of Cu Content on Microstructure and Properties of Al2o3-Sio2 Fiber Reinforced Aluminum Matrix Composites

Effects of Sub-Micron Particles on the Matrix Microstructure of Al Based Composites

Effect of silver plating and sintering temperature on the microstructure and mechanical properties of carbon fiber reinforced Cu matrix composites

Effect of sintering temperature on microstructure and properties of nano-WC particle reinforced copper matrix composites prepared by hot-pressing sintering

Effect of Sintering Temperature on the Microstructure and Properties of High-Strength and Highly Conductive 5 wt.% ZrB2/Cu Composite

Synthesis process and microstructure of carbon fibres/graphite/copper composites by spark plasma sintering

Effect of Sintering Process on Conductivity and Mechanical Properties of In-situ Formed Mo2 C/Cu-based Composite

The Effect of Sintering Temperature on Graphene Oxide Reinforced Copper Matrix Composite Fabricated Through Powder Metallurgy Technique

Effects of Particle Size on Microstructure of the Matrix Alloy in Aluminum Matrix Composites

Influence of characteristic parameters of SiC reinforcements on mechanical properties of AlSi10Mg matrix composites by powder metallurgy

Effect of Sintering Temperature on Microstructure and Mechanical Properties of Hot-Pressed Fe/FeAl2O4 Composite

Effect of SiC particulate on the microstructure of Al-6Ti-6Nb matrix composites fabricated by mechanical alloying technique

Effect of Sintering Temperature on Microstructure and Mechanical Properties of Al2O3/TiAl In-Situ Composites

Fabrication of SiC reinforced aluminium metal matrix composites through microwave sintering

Influence of Pulse Current Auxiliary Sintering and Hot-pressed Sintering on Microstructures and Mechanical Behavior of NiAl-Al2O3 Composite