Investigation on All-Optical Clock Recovery from RZ-Format Data at 64Gbit/s by Using a Two-Section Index-Coupled DFB Laser

Tong Wu,Kun Qiu

2005-01-01

Abstract:High speed all-optical clock recovery from 64Gbit/s RZ-format PRBS data by using atwo-section index-coupled distributed feedback (DFB) laser is simulated and demonstrated. Theperformance of it such as timing jitter, lockup time, locking range are described and analyzed indetail.

What problem does this paper attempt to address?

All-Optical, Bit-Rate Tunable Clock Recovery For Nrz-Ask Signals

Yanqiao Xie,Ying Gao,Jiaojiao Fu,Shiming Gao

DOI: https://doi.org/10.1109/CLEOPR.2009.5292149

2009-01-01

Abstract:All-optical clock recovery is demonstrated for non-return-to-zero amplitude-shift-keying (NRZ-ASK) signals with various bit-rates using a passive asymmetric Mach-Zehnder interferometer (AMI) assisted mode-locked fiber laser. It is available for the bit-rates range from 2.5 to 7 5 Gb/s
Low-timing-jitter all-optical clock recovery for 40 Gbits/s RZ-DPSK and NRZ-DPSK signals using a passively mode-locked quantum-dot Fabry-Perot semiconductor laser

Xuefeng Tang,John C Cartledge,Alexandre Shen,Akram Akrout,Guang-Hua Duan

DOI: https://doi.org/10.1364/ol.34.000899

2009-04-01

Abstract:We investigate experimentally all-optical clock recovery for return-to-zero (RZ) and nonreturn-to-zero (NRZ) differential phase-shift keying (DPSK) signals at 40 Gbits/s using a passively mode-locked quantum-dot Fabry-Perot (QD-FP) semiconductor laser. The QD-FP laser exhibits a beat spectrum linewidth of 80 kHz, which enables a recovered clock signal with a root-mean-square timing jitter of 160 fs for the RZ-DPSK signal and 240 fs for the NRZ-DPSK signal. The timing jitter of the recovered clock signal is characterized for different values of the input signal power and the input signal optical signal-to-noise ratio.
Influence Factors of an All-Optical Recovered Clock from Two-Section Dfb Lasers

Kong Duan-Hua,Zhu Hong-Liang,Liang Song,Wang Bao-Jun,Bian Jing,Ma Li,Yu Wen-Ke,Lou Cai-Yun

DOI: https://doi.org/10.1088/0256-307x/28/9/094209

2011-01-01

Abstract:All-optical clock recovery by a two-section DFB laser with different injection wavelengths is demonstrated experimentally at 38.5 GHz. An optical clock with a root-mean-square timing jitter of 250 fs and an extinction ratio of 12.1 dB is obtained with 1551 nm injection. The timing jitter of the recovered clock is further investigated for various intensity ratios of the two DFB emission modes.
Experimental Demonstration Of An All-Optical Clock And Data Recovery Technology For 10 Gb/S Nrz-Dpsk Signals

Zuqing Zhu,Bo Xiang,Loukas Paraschis,S. J. Ben Yoo

DOI: https://doi.org/10.1109/PS.2007.4300793

2007-01-01

Abstract:We demonstrate an all-optical clock-and-data recovery technology for 10-Gb/s NRZ-DPSK signals. With a relatively simple configuration, the clock-recovery scheme achieves less than 1.5-ps RMS jitter for signals after fiber transmission. The pattern-dependence of data-recovery is within 0.5-dB at BER 10(-9).
100 Gb/s All-Optical Clock Recovery Based on a Monolithic Dual-Mode DBR Laser

Biwei Pan,Liqiang Yu,Lu Guo,Limeng Zhang,Dan Lu,Xin Chen,Yue Wu,Caiyun Lou,Lingjuan Zhao

DOI: https://doi.org/10.3788/col201614.030604

2016-01-01

Abstract:We experimentally demonstrate all-optical clock recovery for 100 Gb/s return-to-zero on–off keying signals based on a monolithic dual-mode distributed Bragg reflector (DBR) laser, which can realize both mode spacing and wavelength tuning. By using a coherent injection locking scheme, a 100 GHz optical clock can be recovered with a timing jitter of 530 fs, which is derived by an optical sampling oscilloscope from both the phase noise and the power fluctuation. Furthermore, for degraded injection signals with an optical signal-to-noise ratio as low as 4.1 dB and a 25 km long distance transmission, good-quality optical clocks are all successfully recovered.
Low timing jitter 40 Gb/s all-optical clock recovery based on an amplified feedback laser diode

Cheng Chen,Jifang Qiu,Lingjuan Zhao,Jian Wu,Caiyun Lou,Wei Wang

DOI: https://doi.org/10.1117/12.922066

2012-01-01

Abstract:We demonstrate 40 Gb/s all-optical clock recovery by using a monolithic integrated amplified-feedback laser (AFL) with coherent injection-locked method. The AFL consists of a gain-coupled DFB laser and an optical amplified feedback external cavity. With proper design and operation of AFL, the device can work at self-pulsation state that resulted from the beating between two lasing modes. The self-pulsation can be injection-locked to the optical clock embedded in input data streams. Due to different work mechanisms, there are two all-optical clock recovery operation modes: incoherent injection-locked and coherent injection-locked. It's predicted that the coherent injection method has various advantages: 1) requiring low injection power recovery, 2) independent of the bit rate and 3) introducing little timing jitter to the recovered clock. The robustness of coherent clock recovery is confirmed by our experimental results. We set up a return-to-zero (RZ) pseudorandom binary sequence (PRBS) data streams all-optical clock recovery system. This coherent injection-locked based clock recovery method is optical signal noise ratio (OSNR) and chromatic dispersion (CD) degeneration tolerant, and has low timing jitter and high sensitivity.
All-optical clock recovery using a ridge width varied two-section partly gain-coupled DFB self-pulsation laser

D.H. Kong,H.L. Zhu,S. Liang,X.F. Zhao,C.X. Lou,L. Wang,B.J. Wang,L.J. Zhao

DOI: https://doi.org/10.1016/j.optcom.2010.06.022

IF: 2.4

2010-01-01

Optics Communications

Abstract:A 1.55μm InGaAsP-InP partly gain-coupled two-section DFB self-pulsation laser (SPL) with a varied ridge width has been fabricated. The laser produces self-pulsations with a frequency tuning range of more than 135GHz. All-optical clock recovery from 40Gb/s degraded data streams has been demonstrated. Successful lockings of the device at frequencies of 30GHz, 40GHz, 50GHz, and 60GHz to a 10GHz sidemode injection are also conducted, which demonstrates the capability of the device for all-optical clock recovery at different frequencies. This flexibility of the device is highly desired for practical uses.
40Gbits/s All-Optical Clock Recovery for Degraded Signals Using an Amplified Feedback Laser

Li Wang,Xiaofan Zhao,Caiyun Lou,Dan Lu,Yu Sun,Lingjuan Zhao,Wei Wang

DOI: https://doi.org/10.1364/ao.49.006577

IF: 1.9

2010-01-01

Applied Optics

Abstract:All-optical clock recovery for the return-to-zero modulation format is demonstrated experimentally at 40 Gbits/s by using an amplified feedback laser. A 40 GHz optical clock with a root-mean-square (rms) timing jitter of 130 fs and a carrier-to-noise ratio of 42 dB is obtained. Also, a 40 GHz optical clock with timing jitter of 137 fs is directly recovered from pseudo-non-return-to-zero signals degraded by polarization-mode dispersion (PMD). No preprocessing stage to enhance the clock tone is used. The rms timing jitter of the recovered clock is investigated for different values of input power and for varying amounts of waveform distortion due to PMD.
All-Optical Clock Recovery From 40 Gbit/S Rz Signal Based On Microring Resonators

Meng Xiong,Yunhong Ding,Qiang Zhang,Xinliang Zhang

DOI: https://doi.org/10.1364/AO.50.005390

IF: 1.9

2011-01-01

Applied Optics

Abstract:A scheme for high-speed clock recovery from return-to-zero (RZ) signal with microring resonators is presented. By using a silicon microring resonator (MRR) for clock extraction and a 3-order nonlinear series-coupled microring resonator (SCMR) for amplitude equalization, clock pulses with amplitude modulation less than 1 dB can be obtained. The proposed scheme is also designed and numerically studied by 3D full vectorial film mode matching method (FMM) and coupled mode theory (CMT). Simulation results show that clock can be recovered at 40 Gbit/s with short rise- and fall-times. (C) 2011 Optical Society of America
All-Optical Clock Recovery of 20 Gbit/S Nrz-Dpsk Signals Using Polarization-Maintaining Fiber Loop Mirror Filter and Semiconductor Optical Amplifier Fiber Ring Laser

Fei Wang,Yu,Xi Huang,Xinliang Zhang

DOI: https://doi.org/10.1016/j.optcom.2009.02.006

IF: 2.4

2009-01-01

Optics Communications

Abstract:All-optical clock recovery (CR) from 20Gbit/s nonreturn-to-zero differential phase-shift-keying (NRZ-DPSK) signals are demonstrated experimentally by using a polarization-maintaining fiber loop mirror filter (PMF-LMF) and a semiconductor optical amplifier (SOA) fiber ring laser. Only by adjusting polarization controller (PC), NRZ-DPSK signals were conveniently and fast converted to pseudo return-to-zero (PRZ) signal via PMF-LMF. Then the PRZ signals are injected into the SOA fiber laser for CR. The recovered clock signals is with the extinction ratio (ER) of 10dB and the root-mean-square (RMS) timing jitter of 750fs in 231−1 long pseudorandom binary sequence (PRBS) NRZ-DPSK signals measurement. Moreover, the broad wavelength tunability of recovered clock stemmed from the use of SOAs as modulator and the gain medium are shown too.
All-optical NRZ-DPSK Clock Recovery Using Linearly Chirped Fiber Bragg Grating Induced Clock Tone

Songnian Fu,Wen-De Zhong,M. Tang,P. Shum,Xia Li

DOI: https://doi.org/10.1016/j.yofte.2007.12.008

IF: 2.8

2008-01-01

Optical Fiber Technology

Abstract:All-optical clock recovery (CR) from 10 Gbps nonreturn-to-zero differential phase-shift-keying (NRZ-DPSK) signal is experimentally demonstrated, by introducing the chromatic dispersion induced clock tone into a free-running semiconductor optical amplifier (SOA) based fiber ring laser for achieving mode-locking. Since no special component is required for NRZ-DPSK demodulation, our proposed method is very promising because of its simple configuration and better stability. The good performance of our proposed configuration is fulfilled with a linearly chirped fiber Bragg grating (LCFBG) to regenerate clock tone of the NRZ-DPSK signal. The recovered clock signal with the extinction ratio of 17 dB and the root-mean-square timing jitter of 540 fs is achieved under 231−1 pseudorandom binary sequence NRZ-DPSK signals measurement. Due to the same operation principle, our configuration has the potential to implement all-optical CR for NRZ-DPSK signal with data rate up to 40 Gbps.
All-Optical Clock Recovery for 20 Gb/s Using an Amplified Feedback DFB Laser

Yu Sun,Jiao Qing Pan,Ling Juan Zhao,Weixi Chen,Wei Wang,Li Wang,Xiao Fan Zhao,Cai Yun Lou

DOI: https://doi.org/10.1109/jlt.2010.2055539

IF: 4.7

2010-01-01

Journal of Lightwave Technology

Abstract:We report all optical clock recovery based on a monolithic integrated four-section amplified feedback semiconductor laser (AFL), with the different sections integrated based on the quantum well intermixing (QWI) technique. The beat frequency of an AFL is continuously tunable in the range of 19.8-26.3 GHz with an extinction ratio above 8 dB, and the 3-dB linewidth is close to 3 MHz. All- optical cl...
All-optical 20 Gbit/s NRZ-DPSK demodulation and clock recovery

Fei Wang,Xinliang Zhang,Jianji Dong,Yu Yu,Xi Huang

DOI: https://doi.org/10.1117/12.803066

2008-01-01

Abstract:All-optical clock recovery (CR) from 20-Gbit/s nonreturn-to-zero differential phase-shift-keying (NRZ-DPSK) signal is demonstrated experimentally by using Polarization-Maintaining Fiber Loop Mirror Filter and semiconductor optical amplifier (SOA) fiber ring laser. Only by adjusting polarization controller (PC), NRZ-DPSK signal were conveniently and fast converted to pseudo return-to-zero (PRZ) signal via PMF-LMF. Then the PRZ signal is injected into the SOA fiber laser for CR. The recovered clock signals with the extinction ratio of 10 dB and the root-mean-square timing jitter of 850 fs is achieved under 2 31-1 pseudorandom binary sequence NRZ-DPSK signals measurement. © 2008 SPIE.
All-optical NRZ-DPSK Clock Recovery Using Chromatic Dispersion Induced Clock Tone

Songnian Fu,M. Tang,Wen-De Zhong,Yang Jing Wen,P. Shum

DOI: https://doi.org/10.1109/lpt.2007.897562

2007-01-01

Abstract:All-optical clock recovery (CR) from 10 Gbps non-return-to-zero differential phase-shift-keying (NRZ-DPSK) signal is demonstrated experimentally, with the chromatic dispersion induced clock tone and semiconductor optical amplifier (SOA)-based mode-locked fiber ring laser. The good performance of our proposed configuration is fulfilled with a 20 km standard single mode fiber to regenerate clock tone of the NRZ-DPSK signal. The recovered clock signal with the extinction ratio over 17 dB and the root-mean-square timing jitter of 718 fs is achieved under 231-1 pseudorandom binary sequence NRZ-DPSK signals measurement.
All-Optical Clock Recovery Using a Single Fabry–Perot Semiconductor Optical Amplifier

Fei Wang,Yu,Yin Zhang,Xinliang Zhang

DOI: https://doi.org/10.1109/jlt.2012.2187173

IF: 4.7

2012-01-01

Journal of Lightwave Technology

Abstract:We present and demonstrate all-optical clock recovery (CR) from the input single-and multiwavelength return-to-zero (RZ) data, using a single multiquantum-well Fabry-Perot semiconductor optical amplifier (FP-SOA) with no additional amplitude equalization measures. The influence of the FP-SOA facet reflectivity on the amplitude equalization of the recovered clock was numerically investigated. A stable 36.55 GHz optical clock with an extinction ratio of 11.0 dB and a root-mean-square timing jitter of 575 fs was extracted from the input, which consisted of 2(23)-1 pseudorandom binary sequences of RZ data. The presented scheme has the potential to perform CR from more than 100 Gbit/s of RZ data, and it has the advantage of wideband and parallel operation.
All-Optical Clock Recovery from Nrz-Dpsk Signals at Flexible Bit Rates

Yu,Zhang Xin-Liang,Dong Jian-Ji,Huang De-Xiu

DOI: https://doi.org/10.1109/lpt.2007.908630

IF: 2.6

2006-01-01

IEEE Photonics Technology Letters

Abstract:We propose and demonstrate all-optical clock recovery (CR) from nonreturn-to-zero differential phase-shift-keying (NRZ-DPSK) signals at different bit rates theoretically and experimentally. By pre-processing with a single optical filter, clock component can be enhanced significantly and thus clock signal can be extracted from the preprocessed signals, by cascading a CR unit with a semiconductor optical amplifier based fibre ring laser. Compared with the previous preprocessing schemes, the single filter is simple and suitable for different bit rates. The clock signals can be achieved with extinction ratio over 10 dB and rms timing jitter of 0.86 and 0.9 at 10 and 20 Gb/s, respectively. The output performances related to the bandwidth and the detuning of the filter are analysed. By simply using a filter with larger bandwidth, much higher operation can be achieved easily.
All-optical Clock Recovery Using Parallel Ridge-Width Varied DFB Lasers Integrated with Y-branch Waveguide Coupler

Duanhua Kong,Hongliang Zhu,Song Liang,Wenke Yu,Caiyun Lou,Lingjuan Zhao

DOI: https://doi.org/10.1016/j.optcom.2011.09.010

IF: 2.4

2012-01-01

Optics Communications

Abstract:A novel device with two parallel ridge-width varied distributed feedback (DFB) lasers integrated monolithically with Y-branch waveguide coupler was fabricated by means of butt-joint regrowth. A 22GHz self-pulsation tuning range has been achieved by adjusting independently the driving currents of the two DFB lasers sections. 38.4GHz all-optical clock recovery has been demonstrated for the first time using this device.
Optical clock recovery with dual-wavelength output from degraded RZ and NRZ signals

Shilong Pan,Caiyun Lou,Xiaofan Zhao,De Ben

DOI: https://doi.org/10.1016/j.optcom.2011.05.029

IF: 2.4

2011-01-01

Optics Communications

Abstract:A novel scheme to implement clock recovery from degraded signals is proposed and demonstrated based on an optoelectronic oscillator and a dual-wavelength mode-locked fiber ring laser with distributed dispersion cavity. The scheme can obtain wavelength-tunable optical clocks at two wavelengths, which is highly desirable for composite optical logic gates, cascaded optical signal processing modules or optical signal processing modules that need synchronized pulses at multiple wavelengths. In addition, the scheme can operate in both RZ and NRZ systems. The feasibility of the method is demonstrated by an experiment, in which dual-wavelength 10-GHz optical clock with a timing jitter less than 170fs is obtained from 10-Gb/s degraded RZ and NRZ signals. The optical clocks can be tuned from 1530 to 1565nm.
Investigation of data-format-transparent multiwavelength all-optical clock recovery using a single FP-SOA

Fei Wang,Xinliang Zhang,Enming Xu

DOI: https://doi.org/10.1016/j.optlastec.2011.02.013

IF: 4.939

2011-01-01

Optics & Laser Technology

Abstract:Multiwavelength clock recovery (CR) is desired to perform all-optical parallel processing, which has potential application in optical communication systems that use WDM technology. Fabry–Pérot semiconductor optical amplifier (FP–SOA) can perform the similar filter function as passive FP filter, and can simultaneously provide gain for oscillation pulses in the cavity; it is essentially an active filter. We experimentally demonstrated simultaneous multiwavelength all-optical CR from input 36.47-Gb/s pseudo-return-zero (PRZ) data and non-return-zero (NRZ) data using a single multi-quantum-well (MQW) FP-SOA with facets reflectivity of 30%. The presented multiwavelength CR scheme is also suitable for PSK signals. Dual-channel CR from input two channels 36.47-Gb/s 223−1 NRZ-DPSK data located at different wavelength is experimentally demonstrated. This scheme is transparent for data formats, which is very important for next generation optical networks.
All-optical Clock Extraction for CSRZ Modulation Data

Zhixin Chen,Xin Jin,Huaihu Cao,Jian Wang

DOI: https://doi.org/10.1007/s12200-009-0009-9

2009-01-01

Frontiers of Optoelectronics in China

Abstract:This paper demonstrates a theoretical investigation on clock extraction from carrier-suppressed return-to-zero (CSRZ) modulation format data at 40 Gbit/s by using a semiconductor optical amplifier (SOA)-based ring laser. A completely numerical analysis about the clock characteristics at 40 Gbit/s is done, which is an effective guide for the experiment and necessary to optimize system performance. The crucial parameters, including the pulse width, energy of the CSRZ data signals and influence of SOA bias current, are analyzed because they determine the quality of the recovered clock pulses. Meanwhile, simulation results show that high-quality clock extraction from 2 7 -1 pseudo-random binary sequence (PRBS) CSRZ data at 40 Gbit/s can be achieved by using higher power assisting continuous-wave (CW) light into a SOA-based ring laser.

Investigation on All-Optical Clock Recovery from RZ-Format Data at 64Gbit/s by Using a Two-Section Index-Coupled DFB Laser

All-Optical, Bit-Rate Tunable Clock Recovery For Nrz-Ask Signals

Low-timing-jitter all-optical clock recovery for 40 Gbits/s RZ-DPSK and NRZ-DPSK signals using a passively mode-locked quantum-dot Fabry-Perot semiconductor laser

Influence Factors of an All-Optical Recovered Clock from Two-Section Dfb Lasers

Experimental Demonstration Of An All-Optical Clock And Data Recovery Technology For 10 Gb/S Nrz-Dpsk Signals

100 Gb/s All-Optical Clock Recovery Based on a Monolithic Dual-Mode DBR Laser

Low timing jitter 40 Gb/s all-optical clock recovery based on an amplified feedback laser diode

All-optical clock recovery using a ridge width varied two-section partly gain-coupled DFB self-pulsation laser

40Gbits/s All-Optical Clock Recovery for Degraded Signals Using an Amplified Feedback Laser

All-Optical Clock Recovery From 40 Gbit/S Rz Signal Based On Microring Resonators

All-Optical Clock Recovery of 20 Gbit/S Nrz-Dpsk Signals Using Polarization-Maintaining Fiber Loop Mirror Filter and Semiconductor Optical Amplifier Fiber Ring Laser

All-optical NRZ-DPSK Clock Recovery Using Linearly Chirped Fiber Bragg Grating Induced Clock Tone

All-Optical Clock Recovery for 20 Gb/s Using an Amplified Feedback DFB Laser

All-optical 20 Gbit/s NRZ-DPSK demodulation and clock recovery

All-optical NRZ-DPSK Clock Recovery Using Chromatic Dispersion Induced Clock Tone

All-Optical Clock Recovery Using a Single Fabry–Perot Semiconductor Optical Amplifier

All-Optical Clock Recovery from Nrz-Dpsk Signals at Flexible Bit Rates

All-optical Clock Recovery Using Parallel Ridge-Width Varied DFB Lasers Integrated with Y-branch Waveguide Coupler

Optical clock recovery with dual-wavelength output from degraded RZ and NRZ signals

Investigation of data-format-transparent multiwavelength all-optical clock recovery using a single FP-SOA

All-optical Clock Extraction for CSRZ Modulation Data