Abstract:Sm2O3 doped ZrO2-based catalysts (Sm2O3–ZrO2 composite oxide) were prepared by co-precipitation and their physical properties (texture and structure) and chemical properties (acid–base and redox) were characterized with the methods of N2 adsorption–desorption isotherm, powder X-ray diffraction, Raman spectroscopy, NH3 and CO2 temperature programmed desorption and H2 temperature programmed reduction. The catalytic performances of the catalysts (activity and selectivities) were evaluated in the CO hydrogenation to isobutene and isobutane (isosynthesis) under the reaction conditions of 673K, 5.0MPa, and 650h−1. The relationship between the catalytic performance and the physical/chemical properties of Sm2O3–ZrO2 catalysts were also examined. The catalytic activity and selectivity of the Sm2O3–ZrO2 catalysts varied with Sm2O3 doping. The physical properties of the catalysts, such as cumulative pore volumes, average pore diameters and crystal sizes had some influences on the activity and selectivity in the isosynthesis. CO conversion increased with an increase in the amount of the acidic sites on the surface of Sm2O3–ZrO2 catalysts, while iso-C4 percentage in total hydrocarbons increased with an increase in the amount of the basic sites. The addition of Sm2O3 into ZrO2 enhanced the reducibility of Sm2O3–ZrO2 catalysts. The highest CO conversion (21.6%) and C4 selectivity (41.8%) were obtained over the catalyst that had a maximum amount of H2 consumptions (57.7μmolg−1) in the TPR measurement for Sm2O3–ZrO2 catalysts. A coordination of the acid–base properties and the redox property may play important role for the improvement of the catalytic performances of the isosynthesis.

Influences Of Preparation Parameters On Catalytic Performance Of Sm2o3 Catalyst In Isosynthesis.

Catalytic Performance Of Samaria-Based Catalysts In Isosynthesis.

Influence of Preparation Parameters on Catalytic Performance of Samaria in Isosynthesis

Sol-Gel Preparation, Characterization and Hydrogenation Property of Silica Supported Ni Catalyst

In Situ Fabrication of Highly Active Γ-Mno2/smmno3 Catalyst for Deep Catalytic Oxidation of Gaseous Benzene, Ethylbenzene, Toluene, and O-Xylene.

Synthesis and Physicochemical Characterization of Hierarchical ZSM-5: Effect of Organosilanes on the Catalyst Properties and Performance in the Catalytic Fast Pyrolysis of Biomass

Properties of Sm2O3–ZrO2 Composite Oxides and Their Catalytic Performance in Isosynthesis

Catalytic and deactivated behavior of SAPO-34/ZSM-5 composite molecular sieve synthesized by in-situ two-step method

Influence of the Sol-Gel Method on a NiO/Al2O3 Catalyst for CH4/O2 to Syngas Reaction

Effects Of Zsm-5 And Sapo-11 On Activity Of Pt/Al2o3 Catalyst

Positive Role of Synthesis Method and Hard Template on the Catalytic Performance of SAPO-34 in Methanol to Olefin Reaction.

Effect of CNT over structural properties of SAPO-34 in MTO process: Experimental and molecular simulation studies

Preparation and characterization of nickel based catalysts on silica, alumina and titania obtained by sol–gel method

The Preparation of Modified ZSM - 35 and its Catalysis Effect Analysis on N-Butene Isomerization

EFFECTS OF HEAT TREATMENT ON STRUCTURE AND PROPERTIES OF ULTRAFINE K-Co-Mo CATALYSTS

Influences of preparation methods of ZrO2 support and treatment conditions of Cu/ZrO2 catalysts on synthesis of methanol via CO hydrogenation

Preparation, Characterization, and Catalytic Performance of ZrO2–SnO2 Nanocatalysts for the Direct Synthesis of DMC

Tuning the CO2 Hydrogenation Activity Via Regulating the Strong Metal–Support Interactions of the Ni/Sm2O3 Catalyst

Nanosized Anatase TiO2 As Precursor for Preparation of Sulfated Titania Catalysts

Influence of Preparation Methods of in 2 O 3 /al 2 O 3 Catalyst on Selective Catalytic Reduction of NO by Propene in the Presence of Oxygen

Promoting effect of sol-gel method and pre-treatment on the activity of SnO 2 /Al 2 O 3 catalyst for NO reduction by propene