A TRANSIENT TEST METHOD FOR THERMAL PERFORMANCE OF FLAT-PLATE SOLAR COLLECTORS

侯宏娟,王志峰,王如竹,祁冰

DOI: https://doi.org/10.3321/j.issn:0254-0096.2004.03.008

2004-01-01

Abstract:A fast, transient test method for solar flat-plate collectors was introduced. The characteristic parameters FR(τα)e, FRUL estimated from this method were close to those obtained from the Chinese National Standard of GB/T 4271-2000.

What problem does this paper attempt to address?

Heat Transfer Performance Analysis on a PVT Collector Fabricated by Modifying a Commercial Solar Cell

DU Qiang,TANG Ke

DOI: https://doi.org/10.3969/j.issn.1004-3950.2011.02.009

2011-01-01

Energy Engineering

Abstract:A commercial crystal silicon solar cell is modified into a PVT(Photovoltaic /Thermal) collector module by adding a water cooler.Thermal resistance analysis is conducted to discuss the heat transfer performance of the modified PVT collector.And experiments are also performed to measure the thermal resistance and the effective thermal conductivity of the PVT collector for further development.
EXPERIMENTAL METHODS RESEARCH ON SOLAR COLLECTOR TIME CONSTANT

Hou Hongjuan,Wang Zhifeng,Wang Ruzhu,Wang Peiming

2006-01-01

Abstract:The solar collector time constant indicates the response rate of the collector under the step-input.Tome constant test is one of the important contents of the collector thermal performance test.How to determine it accurately by simple experimental method is worthy to be studied.In this paper a new method was proposed based on the established standards.It is simple and has been validated.
Experimental Study on New Flat Plate Solar Water Heater

王世锋,胡亚才,俞自涛

DOI: https://doi.org/10.3969/j.issn.1004-3950.2003.06.004

2003-01-01

Energy Engineering

Abstract:Applying cellular technology and heat pipe technology in flat plat solar water heater can greatly reduce heat losing and enhance average daily coefficient. Many times experiments prove that the average daily efficiency of flat plat solar water heater using cellular technology and heat pipe technology is higher than that of evacuated tubular solar water heater, on the opposition the average heat loss efficiency is much less. So the new flat plate solar water heater have popularizing and applying value.
SOLAR THERMAL PERFORMANCE OF ALL-GLASS EVACUATED COLLECTOR TUBES

殷志强

DOI: https://doi.org/10.3321/j.issn:0254-0096.2001.01.001

1998-01-01

Abstract:Three solar thermal parameters,i.e.heat loss coeffi cientULT,irradiation H and stagnation par ameter Y of all-glass evacuated collector tubes were derived on the basis of energy balance equation,which depen ds on solar transmittance of cover glass tube,solar absorptance and thermal emit tance of the selective absorbing surface and gas pressure in the jacket between cover and inner glass tubes,and solar irradiance,temperatures and the geometry o f the collector tube.Calculated results of solar thermal parameters of all-glass evacuated collector tubes agree well with experiments.These solar thermal param eters of all-glass evacuated collector tube were adopted by China national stand ard GB/T 17049-1997.
A New Method for the Measurement of Solar Collector Time Constant

HJ Hou,ZF Wang,RZ Wang,PM Wang

DOI: https://doi.org/10.1016/j.renene.2004.08.005

IF: 8.7

2005-01-01

Renewable Energy

Abstract:A new test method about the time constant of the solar collector has been presented in this paper. It is simple and has been validated through experiments. With the new method it is not necessary to adjust the inlet temperature of the transfer fluid as closely as possible to the ambient air temperature. Also, it is not necessary to know the characteristic parameters of the collector in advance. The model used in the paper is a first order system model, as in most cases. The experimental data obtained from the test of solar collector time constant shows that the solar collector is not a strictly first order system. A criterion is proposed to decide whether the system is a first order system or not and the resemblance of the system to the first order system.
The analysis and testing of thermal performance on solar evacuated tube

Tao ZHANG,Jitian HAN,Suying YAN,Zeting YU,Ran ZHOU

DOI: https://doi.org/10.6040/j.issn.1672-3961.0.2014.006

2014-01-01

Abstract:The joint application test bench for solar-thermal photovoltaic was set up to study solar Kalina cycle.The a-nalysis and testing of thermal performance on solar evacuated tube was carried out with methods of experimental and nu-merical simulation through the experiment platform of single tube solar water heater.The temperature and velocity field of single tube solar water heater were visible analyzed with field synergy principle.The study showed that the two di-mensional numerical calculation model could accurately reflect the trend of all-glass evacuated tube solar water heater in the same conditions and the coefficient of field synergy on evacuated tube which was equipped with guide plate was su-perior to other structures.It was finally confirmed that the Φ58 mm ×1 800 mm of solar evacuated tube equipped with reflector and guide plate was the best choice.
Testing on the Transient Heat Loss Coefficient of All-Glass Evacuated Tube Collectors in Severe Cold Areas

Huifang Liu,Yiqiang Jiang,Yang Yao

DOI: https://doi.org/10.18178/jocet.2016.4.5.306

2015-01-01

Journal of Clean Energy Technologies

Abstract:The insulation features and the heat dissipation was important factors that influence the utilization of all-glass evacuated tube collector, especially in severe cold areas. The heat loss coefficient of evacuated tube collector was usually tested in given conditions, which was inapplicable for actual conditions. In this paper, further study was conducted base on the previous research of anti-freezing strategies of solar collecting loop in sever cold areas. The heat transfer of evacuated tube collector in winter night was established based on the heat balance equation. The heat loss coefficient of solar collector, as well as the possible fluid temperature in it, was tested and analyzed in detail. It indicated that the initial fluid temperature in solar collector was usually higher than 20C in most of the days, and it would be still above 5C throughout the whole night. The transient heat loss coefficient was mostly around at 0.4 W/m·K to 0.6 W/m·K. The values of heat loss coefficient was steady in each night with slight reduction, which can be taken as a reference to estimate the possible fluid temperature in the solar collector and the heat dissipation in similar weather conditions. Results demonstrated that the solar collector has better insulation property, which was advantageous for the anti-freezing of collectors and outdoor pipes in severe cold areas.
A dynamic thermal performance model for flat-plate solar collectors based on the thermal inertia correction of the steady-state test method

Jie Deng,Yupeng Xu,Xudong Yang

DOI: https://doi.org/10.1016/j.renene.2014.12.005

IF: 8.7

2015-01-01

Renewable Energy

Abstract:In determining the dynamic thermal performance of a flat-plate solar collector, when the instantaneous solar irradiance changes sharply at one moment, most of the existing models cannot accurately predict the momentary thermal characteristics of outlet temperature and useful heat gain. In the present study, an analytical model in the form of series expansion is put forward to depict the momentary thermal characteristics of flat-plate solar collectors. The analytical model reveals that, instantaneous useful heat gain of a solar collector at one moment consists of the steady-state useful heat gain and corresponding thermal inertia correction. The model is then validated by the experimental data. It indicates that the analytical model can properly predict the dynamic thermal performance of the solar air collector. Besides, the model pertains to other types of solar thermal collectors, if they can be tested by the steady-state test method.
Experimental Study of a Novel Testing Platform for the Thermal Performance of Solar Domestic Water Heating Systems

Yihong Yang,Yanqiu Wang,Wei He

DOI: https://doi.org/10.1016/j.egypro.2015.02.109

2015-01-01

Energy Procedia

Abstract:Solar domestic water heating systems (SDWHS) are widely used in China, with an installed collector area of more than 330 million square meters by the end of 2014.Many relevant products keep on launching and upgrading in the market. To regulate the market, the performance of products, especially new products should be evaluated by thequality supervisionagency. However, all the existing national standards of thermal performance tests forSDWHSrequire that the daily solar irradiationgain should be more than 16MJ/m2.Thus, only a small part of days in a year meet this criteria, which constrained quality supervisionagencies to regulate the solar heater market. A new approach of testing platform for the thermal performance of SDWHS is also presented in this manuscript. The testing platform consists of a sun-tracking flat-mirror reflector which not only directs the sunlight to the collector to increase the daily solar irradiation gain but also produces a light spot of 2×2 m2. A large number of experiments have been conducted to measure the performance of the testing platform. Results show that on one hand the platform can increase the daily gain of solar irradiation to 16MJ/m2 from 12MJ/m2, and on the other hand the light spot has a non-uniformity of less than 3%. Experiments onSDWHShavebeen performed on the platform as well as on the ground, respectively. It has been found that the relative difference of the daily thermal efficiency measured by the two methods is lower than 3%.
Experimental Research on the Thermal Performance of Unglazed Transpired Solar Air Collectors

GAO Li-xin,SUN Shao-zeng,WANG Yuan-feng

DOI: https://doi.org/10.3969/j.issn.1002-6339.2012.02.014

2012-01-01

Abstract:Unglazed transpired solar air collectors have proven to be effective devices for ventilation air preheating and drying,which can be integrated with building easily.An experimental rig with solar collector area of 2.2 m2was set up to test the thermal performance of a solar air heating system based on unglazed transpired solar collectors,and a series of experiments were conducted under real transient outdoor conditions from February 2009 to April 2009.Test results show that exit air temperature increase with increasing solar irradiation.The most important influencing factor on exit air temperature is solar irradiation,while the influence of ambient air temperature is negligible.Temperature rise decreases with increasing air flow rate,while collector thermal efficiency increases with increasing air flow rate.The average thermal efficiency of the experimental solar air heating system in the 3-day test period was 58%,63%,and 72%,respectively,which are higher than most conventional glazed flat-plate solar air collectors.
Dynamic Thermal Performance Prediction Model for the Flat-Plate Solar Collectors Based on the Two-Node Lumped Heat Capacitance Method

Jie Deng,Rongjiang Ma,Guofeng Yuan,Chun Chang,Xudong Yang

DOI: https://doi.org/10.1016/j.solener.2016.06.060

IF: 7.188

2016-01-01

Solar Energy

Abstract:Two-node lumped heat capacitance model of the flat-plate solar collectors is derived strictly based on the concept of the collector flow efficiency factor F'. It is found that the obtained first-order differential model turns out to be the amended quasi-dynamic test (QDT) model. The collector dynamic response time constant tau(d) is identified referring to the first-order response system in automatic control theory. Then the dynamic thermal performance prediction model for the flat-plate solar collectors on the basis of the amended QDT model is deduced using integral treatment within a small time interval in order to extend the thermal inertia correction model (TICM) to be fit for different conditions, such as moderate or intensive change rates of the collector inlet temperature, wide-range ratios of the diffuse radiation to global radiation, different incidence angles, etc. Correlation between the presented prediction model and the TICM base on the steady-state test (SST) for the flat-plate solar collectors is elucidated and the relation between the collector dynamic response time constant tau(d) and the static time constant tau(c) is elaborated. Finally, experimental tests of both the steady-state tests and dynamic tests with a specific flat-plate solar air collector are conducted to verify the performance of the proposed dynamic prediction model and corresponding parameters. It is verified that the presented prediction model in terms of the collector dynamic response time constant tau(d) can accurately predict the dynamic thermal performances of the flat-plate solar air collector under different conditions. (C) 2016 Elsevier Ltd. All rights reserved.
STUDY OF THERMAL PERFORMANCE OF A NOVEL DUAL-FUNCTION FLAT PLATE SOLAR COLLECTOR

Ji Jie,Ma Jinwei,Sun Wei,Zhang Yang,Fan Wen,He Wei,Zhang Aifeng

DOI: https://doi.org/10.19912/j.0254-0096.2011.10.009

2011-01-01

Abstract:A novel flat-plane solar collector with L-shaped fins was proposed in this paper,which worked as air heater or water heater according to the season and applications.Experimental investigation was carried out to study the performance of the collector under different operating conditions.The experimental results indicate that the thermal efficiency reaches 40% as air heater that is higher than conventional flat plane air heater,the thermal efficiency of the collector is 49.7% as water heater.Therefore the novel collector can be applied as both air heater and water heater with high efficiency.
Experimental Analysis of a Novel Solar PV/T Collector

Ma Jinwei,Tong Weiwei,Fang Tingyong,He Wei,Wang Kesheng

DOI: https://doi.org/10.1051/e3sconf/201913602043

2019-01-01

E3S Web of Conferences

Abstract:The output power of the solar photovoltaic panel decreases as the operating temperature increases. The use of photovoltaic/photothermal (PV/T) collectors not only effectively cools the operating temperature of the battery, increases photovoltaic power, but also produces hot water. Therefore, the PV/T collector improves the annual utilization efficiency of solar energy, and can meet the user's demand for different energies. This paper builds an experimental platform to compare the PV/T collector photovoltaic/photothermal performance and experimental comparison with traditional PV. The results show that the PV/T collector has a thermal efficiency of 31.5% and a photovoltaic efficiency of 17.82% at a flow rate of 0.023 Kg/s to achieve high efficiency in solar energy utilization.
A New Performance Evaluation Method for Solar Thermosyphon Systems

Q. Y. Jiang,Wei He,J. X. Hou,Jie Ji

DOI: https://doi.org/10.1093/ijlct/ctq029

IF: 2.3

2010-01-01

International Journal of Low-Carbon Technologies

Abstract:The thermal performance of a solar thermosyphon system for water heating depends on its design characteristics and manufacturing quality. For product improvement and quality control purposes, standardized tests are performed and system characteristic parameters are determined through statistical analysis of measured data. A number of national and international test methods are currently available. However, the characteristic parameters derived from these tests are dependent on the relative sizes of the major components, such asmass of water in system in relation to the collector aperture area. The methods are therefore not good enough to serve for direct system comparison purpose. This article introduces a new evaluation method based on M/A(c) = 75 kg/m(2) and 50% system efficiency at zero reduce temperature. The four characteristic parameters, namely alpha(eff), u(eff), u(50), and PF50, are independent of the M/A(c) ratio, and by analyzing the four characteristic parameters, we can assess not only the solar thermosyphon system performance, but also the direction for system performance improvement.
Study on the second-order transfer function models for dynamic tests of flat-plate solar collectors Part I: A proposed new model and a fitting methodology

jie deng,xudong yang,pengsu wang

DOI: https://doi.org/10.1016/j.solener.2015.01.046

IF: 7.188

2015-01-01

Solar Energy

Abstract:•The second-order differential TFMs for solar collector dynamic tests are reviewed.•A new form of TFM in terms of the collector heat removal factor is developed.•Equivalent relationships among the TFMs are illustrated.•The methodology of fitting for the model coefficients in the TFMs is elucidated.
Heat Exchange Performance Test of a Magnetic Nanofluid Heat Pipe Solar Heat Collector

Yun-feng ZHANG,Xun XIA,Song-rong LUO,Tao LI

DOI: https://doi.org/10.16146/j.cnki.rndlgc.2018.02.017

2018-01-01

Abstract:Designed was a heat exchange system test rig.With a magnetic nanofluid and water serving as the working media in a heat pipe respectively,a contrast test of a glass vacuum tube and internally inserted heat pipe type solar heat collector was conducted to analyze the photothermal conversion momentary efficiency and daily averaged efficiency of the two collectors at different inclination angles,weather conditions,total solar irradiances.In addition,the average heat loss coefficients of the two collectors were compared.It has been found that the average heat loss coefficient of the internally inserted heat pipe type collector is about 2.32％ of that ofthe whole glass vacuum tube collector,far less than that of the whole glass vacuum tube collector and that of the heat pipe type glass vacuum tube solar heat collector with the nanofluid serving as the working medium is far less than that of the heat pipe vacuum heat collector with water serving as the working medium and its momentary efficiency an daily averaged efficiency are far higher,thus securing an even higher efficiency,safe and stable operation.
Experimental Study of Solar Air Heating System Based on Unglazed Transpired Collector

Lixin Gao,Hua Bai,Xiumu Fang

DOI: https://doi.org/10.1115/es2011-54837

2011-01-01

Abstract:An experimental rig was set up to test the thermal performance of a solar air heating system based on an unglazed transpired collector of 2.5 m2. The experiment was carried out at Harbin Institute of Technology in the city of Harbin, which is located in northeastern China, at latitude 45°41′ N and longitude 126°37′ E. The tests were spread over a number of days, in which the 4-day experimental data within the period were selected as the sample for analysis. Experimental results show that solar collector’s surface temperature and exit air temperature increase with increasing solar irradiation. The influence of ambient temperature on surface temperature and exit temperature is negligible. Temperature rise decreases with increasing air flow rate, while collector efficiency increases with increasing air flow rate. For an air flow rate of 100 m3/h in Test 1, the average air temperature rise and collector efficiency were 28.86°C and 72% respectively; for an air flow rate of 235 m3/h in Test 2, the average air temperature rise and collector efficiency were 11.52°C and 78% respectively. Higher airflow rate tends to operate the collector at lower surface temperature, which results in lower overall heat losses from the collector to the surroundings, therefore increasing airflow rate reduces air temperature rise and enhances the collector efficiency. The average efficiency of the experimental solar air heating system in the 4-day experiment period was 72%, 78%, 61%, and 72% respectively, which are higher than most conventional glazed flat-plate solar air collectors. With better coordination with architectural design at early stage in a project, this building-integrated solar air heating system can be both aesthetically and technically viable.
NUMERICAL STUDY ON THE ELECTRIC AND THERMAL PERFORMANCE OF HYBRID PV/T COLLECTOR WALL

Ji Jie,Han Jun,Zhou Tiantai,He Wei,Pei Gang,Lu Jianping

DOI: https://doi.org/10.3321/j.issn:0254-0096.2006.11.004

2006-01-01

Abstract:A numerical simulation method has been used to analyze the electric and thermal performance of hybrid photovoltaic and thermal collector wall.The effects of the packing factor,working fluid mass flow rate on the thermal efficiency and electric gain were investigated,and the optimization of design parameters have been found in this paper.
Experimental comparison of the thermal performance of unglazed transpired collectors

GAO Li-xin,WANG Tian-cheng,SUN Shao-zeng

2012-01-01

Abstract:The thermal performances of black,dark green and dark blue unglazed transpired solar collectors were tested and compared under real transient outdoor conditions using an experimental solar air heating system.The test results show that solar irradiation and air flow rate are the main influencing factors for the thermal performance of solar air heating system.The average instantaneous thermal efficiency of the black collector under high and low air flow rate is 76.04% and 67.50%,respectively,which are higher than that of conventional glazed flat-plate solar air collectors.Surface color of solar air collectors has effect on its thermal performance.The average instantaneous thermal efficiency of the dark green and dark blue collector under high and low air flow rate is 15% to 22% lower than that of the black collector,temperature rise is 3～4 ℃ lower than that of the black collector.However,the thermal performances of dark green and dark blue collector are better than that of conventional flat-plate collectors.Thus,the thermal performance penalty will not be very high with the application of colored unglazed transpired collectors on building facade for aesthetic reasons.
Heat Loss and Energy Efficiency Investigation of Vacuum Flat Plate Photovoltaic/Thermal Collectors

Xue Li,Ken Chen,Yu Pei,Shuyi Chen,Hai Zhou,Zhongyi Ren,Lin Tang,Qiongwan Yu,Junsheng Feng,Gang Pei

DOI: https://doi.org/10.1016/j.renene.2024.121353

IF: 8.7

2024-01-01

Renewable Energy

Abstract:Solar energy photovoltaic/thermal (PV/T) technology is significant for achieving carbon neutrality. However, when the temperature difference between the PV/T module and the ambient environment increases, the thermal efficiency significantly decreases due to high heat losses. In this study, a novel vacuum flat plate PV/T collector with spectral selectivity is proposed, and the effects of vacuum environment and absorber emissivity on the convective, conductive, and radiative heat losses in the PV/T collector are comprehensively analyzed. The results indicate that the convective and conductive heat losses in the PV/T collector are relatively reduced by about 97% when the air gap pressure is reduced to 0.10 Pa. When the emissivity of the PV/T absorber decreases from 0.9 to 0.1, the radiation heat loss relatively reduces by over 70%. Compared to the conventional PV/T collector, the novel PV/T collector demonstrates the most significant performance improvement in winter. The thermal efficiency of the novel PV/T collector with an inlet water temperature of 50°C can maintain approximately 50% throughout the year. Even when the inlet water temperature increases to 90°C, the novel PV/T collector can still be maintained at a thermal efficiency of 34% in winter, whereas conventional PV/T collectors cannot collect heat in any season.

A TRANSIENT TEST METHOD FOR THERMAL PERFORMANCE OF FLAT-PLATE SOLAR COLLECTORS

Heat Transfer Performance Analysis on a PVT Collector Fabricated by Modifying a Commercial Solar Cell

EXPERIMENTAL METHODS RESEARCH ON SOLAR COLLECTOR TIME CONSTANT

Experimental Study on New Flat Plate Solar Water Heater

SOLAR THERMAL PERFORMANCE OF ALL-GLASS EVACUATED COLLECTOR TUBES

A New Method for the Measurement of Solar Collector Time Constant

The analysis and testing of thermal performance on solar evacuated tube

Testing on the Transient Heat Loss Coefficient of All-Glass Evacuated Tube Collectors in Severe Cold Areas

A dynamic thermal performance model for flat-plate solar collectors based on the thermal inertia correction of the steady-state test method

Experimental Study of a Novel Testing Platform for the Thermal Performance of Solar Domestic Water Heating Systems

Experimental Research on the Thermal Performance of Unglazed Transpired Solar Air Collectors

Dynamic Thermal Performance Prediction Model for the Flat-Plate Solar Collectors Based on the Two-Node Lumped Heat Capacitance Method

STUDY OF THERMAL PERFORMANCE OF A NOVEL DUAL-FUNCTION FLAT PLATE SOLAR COLLECTOR

Experimental Analysis of a Novel Solar PV/T Collector

A New Performance Evaluation Method for Solar Thermosyphon Systems

Study on the second-order transfer function models for dynamic tests of flat-plate solar collectors Part I: A proposed new model and a fitting methodology

Heat Exchange Performance Test of a Magnetic Nanofluid Heat Pipe Solar Heat Collector

Experimental Study of Solar Air Heating System Based on Unglazed Transpired Collector

NUMERICAL STUDY ON THE ELECTRIC AND THERMAL PERFORMANCE OF HYBRID PV/T COLLECTOR WALL

Experimental comparison of the thermal performance of unglazed transpired collectors

Heat Loss and Energy Efficiency Investigation of Vacuum Flat Plate Photovoltaic/Thermal Collectors