Abstract:The process of preparing SiC fiber-reinforced γ -TiAl composites by the conventional methods is difficult and complicated due to the high reactivity, high melting point and poor deformability of γ -TiAl alloys. In this work, suction casting, a promising method for preparing SiC f /TiAl composite, had been attempted. In the process, γ -TiAl alloy melt was introduced rapidly into a mold within pre-arranged fibers that were coated with additional layer of titanium alloy. This simple method successfully prevented serious reactions between the alloy melt and the fibers which remained intact during the solidification process. The interfacial reaction layer was observed by optical microscopy, scanning electron microscopy (SEM). The interfacial reaction products were identified by transmission electron microscopy (TEM). Tensile tests of the matrix alloy and composites were performed at room temperature and 800 °C. The results exhibited that the tensile strength of SiC f / γ -TiAl composite was higher than that of the matrix alloy at both room temperature and 800 °C. At room temperature, tensile strength of SiC f / γ -TiAl composite was increased by about 7% (50 MPa), whereas a double increase in tensile strength 14% (100 MPa) was obtained at 800 °C. The titanium alloy coating on the fiber not only prevented the serious interfacial reaction between the γ -TiAl alloy melt and the SiC fiber, but also played a role in delaying the propagation of cracks in the matrix to the fiber at 800 °C. The fracture mechanism of the composite was analyzed by fracture metallographic analysis.

Strengthening and toughening of TiC ceramics by short carbon fibers

Mechanical properties of short carbon fiber-reinforced TiC composites produced by hot pressing

Strengthening and toughening of Ti 5 Si 3 by TiC-coated short carbon fiber: Fabrication, interfacial control, and mechanism of reinforcement

Synthesis of Ti<sub>3</sub>SiC<sub>2</sub> from TiC and Si and its toughening mechanism with incorporated carbon fibers

Tough and wear-resistant carbon fiber reinforced TiC-based composite prepared by alloyed melt infiltration at low temperatures

Solidification Microstructure, Fracture Behavior and In-Situ Toughening of TiC-TiB2 Fine-grained Composite Ceramics

Experimental Description of Thermomechanical Properties of Carbon Fiber-Reinforced Tic Matrix Composites

Toughening Mechanism Of Short Carbon Fiber Reinforced Reaction Bonded Silicon Carbide Composite Ceramic

Mechanical Properties and Strengthening Mechanisms of in Situ (Tib+tic)/ti-1100 Composite at Elevated Temperature

Effect of Carbon Reactant on Microstructures and Mechanical Properties of Tial/Ti2alc Composites

Influence of Hot-Pressing Parameters on the Mechanical Properties of TiC Composites Reinforced with Carbon Fibers

Mechanical Properties and Strengthening Effects of in Situ (Tib+tic)/ti-1100 Composite at Elevated Temperatures

Developing High Toughness and Strength Al/TiC Composites Using Ice-Templating and Pressure Infiltration

Strengthening Effects of Tic Particles and Microstructure Refinement in in Situ Tic-Reinforced Ti Matrix Composites

Effect of Carbon Element on Mechanical Properties of in Situ 5 Vol% TiC/Ti-1100 Composite

Study on mechanical properties of C-f/TiC-TiB2 composites combustion-synthesized by SHS

Microstructure and mechanical properties of TiB2-40 wt% TiC composites: Effects of adding a low-temperature hold prior to sintering at high temperatures

Mechanical properties and fracture behavior of CVI-SiC/TaC modified C/C composite

Investigation on the Microstructure, Room and High Temperature Mechanical Behaviors and Strengthening Mechanisms of the (tib+tic)/tc4 Composites

Tensile Behavior of SiC Fiber-Reinforced Γ -Tial Composites Prepared by Suction Casting

Fabrication and Characterization of a Carbon Fibre Reinforced Carbon–silicon Carbide–titanium Silicon Carbide Hybrid Matrix Composite