Abstract:The influence of post-synthetic modifications of Al-rich ZSM-5 (Si/Al ratio ca. 10) involving alkaline and subsequent acid treatments on the textural, acidic and catalytic properties in the cracking of bulky hydrocarbon molecules at low temperature is reported. It was found that the optimized base treatment, i.e. 0.5 M NaOH should be used for the substantial generation of intracrystal mesoporosity while preserving the intrinsic zeolite properties of ZSM-5 zeolite. A subsequent strong acid washing, i.e. 0.5 M HCl is required to completely remove Al-rich debris formed during the base treatment, thereby improving the textural and acidic properties. The catalytic performance of the parent and treated ZSM-5 materials was evaluated in the gas phase cracking of 1,3,5-triisopropylbenzene (TIPB) and cumene as test reactions. The results showed that under the applied cracking conditions, the introduction of mesoporosity by the optimized base–acid treatments on the one hand increased the accessibility of Brønsted acid sites, producing a higher TIPB conversion (82.5% as compared to 61.9% of the parent ZSM-5), on the other hand, it promoted the transformation of pre-cracking products, leading to a higher selectivity to deep cracking products, i.e. the selectivity of cumene and benzene of 22.7% as compared to 17.6% of the parent ZSM-5. A similar conclusion has been reached in the cracking of cumene where the presence of considerable mesoporosity indeed improved cumene reactivity of the alkaline and acid treated ZSM-5 as its density of strong zeolite Brønsted sites was mainly retained.

Comparative study of catalytic cracking performance of NBMAS, AlMCM-41, amorphous silica-alumina and HZSM-5

Comparative Study on the Structural, Acidic and Catalytic Properties of Nano-Sized and Large-Particulate Mesoporous Aluminosilicates

Comparative study on the acidic and catalytic properties of AlMSU-2- and AlMCM-41-like samples: both synthesized from the same zeolite-like precursor

High Activity in Catalytic Cracking over Stable Mesoporous Aluminosilicates

Synthesis Of Mesoporous Aluminosilicate Nanoparticles And Its Performance In Catalytic Cracking

Synthesis and Catalytic Performances of Mesoporous Aluminosilicates of Cubic and Hexagonal Structure with Stronger Acid Sites

Effects of post treatment of HZSM-5 zeolites on catalytic cracking of butene

Catalytic oxidation of isoamyl alcohol on modified ZSM-5 molecular sieve catalysts prepared by different methods

Hydrocracking of Bio-Alkanes over Pt/Al-MCM-41 Mesoporous Molecular Sieves for Bio-Jet Fuel Production

Catalytic cracking of n-hexane over HZSM-5 zeolites

Influence of post-synthetic treatments of aluminum-rich ZSM-5 on the catalytic cracking of bulky hydrocarbons at low temperature

Preparation and Alkylation Performance of HMCM-41 Mesoporous Molecular Sieve

HZSM-5/MCM-41 composite molecular sieves for the catalytic cracking of endothermic hydrocarbon fuels: nano-ZSM-5 zeolites as the source

Synergetic Regulation of the Microstructure and Acidity of HZSM-5/MCM-41 for Efficient Catalytic Cracking of n-Decane

A Mesoporous Aluminosilicate Prepared By Simply Coating Fibrous Gamma-Alooh On The External Surface Of Sba-15 For Catalytic Hydrocarbon Cracking

Synergetic Regulation of the Microstructure and Acidity of HZSM-5/MCM-41 for Efficient Catalytic Cracking of <i>n</i>-Decane

Catalytic Cracking of Supercritical N-Dodecane over Meso-Hzsm-5@al-mcm-41 Zeolites

Comparative Research on the Supercritical Catalytic Cracking of n-Dodecane and Kerosene Using Nanosheet MFI Zeolite

Catalytic Cracking of Endothermic Fuels over Meso-HZSM-5/MCM-41 Coatings

HZSM-5 Zeolites Undergoing the High-Temperature Process for Boosting the Bimolecular Reaction in N-Heptane Catalytic Cracking

Roles of Molecular Structure in the Catalytic Cracking of N‐heptane, Methylcyclohexane and Cyclopentene over HZSM‐5 Zeolites