Abstract:Hollow fiber membranes fabricated via dry/wet phase inversion method usually have two dense skin layers,which will increase its resistance of mass transport as a support membrane. It is necessary that the dense skin layer of support membrane has been eliminated to improve separation performance of composite membrane. The excellent. chemical resistance of poly(vinylidene fluoride) (PVDF) to many acids and alkalis has made it as an attractive membrane material, and then it's often fabricated as porous hollow fiber membrane by phase inversion. In the process, the formation of the skin layer is due to the rapid exchange between solvent and coagulation, so many attempts have been made to slow it, so as to control the formation of the skin layer. In this paper, it has been found that the fabrication progress becomes unstable, and the membrane prepared has noncircular lumen, when the "weak" or "soft" coagulation is used. To increase the fabrication solution stability during membrane formation, dope viscosity was focused in this experiment. Dimethyl acetamide (DMAc) was used as solvent as well as internal coagulant, and the additives including LiCl, water and surfactant Span were chosen to investigate their effect oil the viscosity of the fabrication solution. The dope viscosity will greatly increase after adding LiCl, while the variety of dope viscosity is unconcerned in the fabrication solution concentration as adding water. The homogenization and stability of the fabrication solution are improved by adding Span,and the viscosity increases at the same time. Without increasing PVDF concentration, the stability of the nascent membrane was improved by increasing the fabrication viscosity. The PVDF hollow fiber membrane with the structure of single outer skin layer and finger-like pore through the cross-section, has been successfully fabricated. The mean pore radius and water flux of the single skin hollow fiber membrane were greatly improved.

Influence of additives on phase separation process of PVDF solution and membrane morphology

The Polymer-rich Phase Solidification Process of PVDF-PVP-DMAc-H2O Solution

Effect of solvent concentration on development of macrovoids of PVDF phase-diversion membranes

Effects of Preparing Condition on PVDF Membrane Morphology

Effect of Additives on the Morphology and Performance of Symmetric Network PVDF Membranes

Influence of Solvents on the PVDF Membrane Properties

Modification of Porous Poly(Vinylidene Fluoride) Membrane Using Amphiphilic Polymers with Different Structures in Phase Inversion Process

Porous Membranes Modified by Hyperbranched Polymersi. Preparation and Characterization of PVDF Membrane Using Hyperbranched Polyglycerol As Additive

Preparation and Characterization of Poly(vinylidene Fluoride) Flat Sheet Membrane with Tg Tunable Amphiphilic Terpolymer As Membrane Additive

Preparation of Porous PVDF Membrane Via Thermally Induced Phase Separation with Diluent Mixture of DBP and DEHP

Polymorphism in Porous Poly(vinylidene Fluoride) Membranes Formed Via Immersion Precipitation Process

Influence of Dope Viscosity on the Fabrication of Pvdf Hollow Fiber Membranes with Single Skin Layer

INFLUENCE OF ALCOHOL-BASED NONSOLVENTS ON THE FORMATION AND MORPHOLOGY OF PVDF MEMBRANES IN PHASE INVERSION PROCESS

Morphology and Formation Mechanism of Poly(Vinylidene Fluoride) Membranes Prepared with Immerse Precipitation: Effect of Dissolving Temperature

Effect of Coagulation Bath Temperature on Formation Mechanism of Poly(vinylidene Fluoride) Membrane

Effect of Maturation Time of Dopes on the Morphology and Crystallization of PVDF Membranes

Formation Mechanism and Crystallization of Poly(vinylidene Fluoride) Membrane Via Immersion Precipitation Method

Fluid simulation of different solvents and additives for the preparation of PVDF blended membranes by NIPS method

Effect of Polymer Molecular Weight on the Morphology and Crystallization of Prepared PVDF Membranes

Effect of Non-Solvent Additives on the Morphology and Separation Performance of Poly(m-Phenylene Isophthalamide) (PMIA) Hollow Fiber Nanofiltration Membrane

Influences of adding organic intermediate layer on membrane formation and properties