Abstract:The surface of many key components used in petrochemical industry may be damaged by corrosion, wear and overheat during service. This damage can make a significant impact on the safe and reliable operation process of the device. Low alloy steel is widely used to manufacture pressure vessels and pipes because of the higher strength and good processing properties, but has poor corrosion resistance and wear resistance. Laser cladding is an advanced and effective surface modification technology. It can improve the surface properties of the matrix material at lower cost. But these claddings crack easily due to the high temperature gradient in the laser molten pool and physical properties differences between the cladding material and matrix This problem has affected the development of laser cladding. Laser high frequency induction hybrid cladding is a novel technology which combines laser beam heat source and induction power. It can decrease the cracks in the claddings effectively and has been received significant attentions in recent years.Nickel base alloy powders have good corrosion resistance, wettability and high temperature lubricity. In this research, NiCrBSi composite claddings were fabricated on the surface of low alloy steel by the way of laser-high frequency induction hybrid cladding and coaxial powder feeding. The optimum cladding technology parameters to obtain the cladding layers that with good metallurgical combination, reasonable dilution rate and without cracks and defects were developed by optimizing the processing parameters such as laser power, powder feeding rate, laser scanning speed and induction heating temperature. The hardness distribution, microstructure, element distribution and phase of the cladding layers fabricated by the optimum parameters were systematically investigated by means of micro-hardness tester, optical microscopy (OM). Compared with the untreated material, experiment results show that the micro-hardness from substrate to NiCrBSi cladding layer exhibits step distribution, and the hardness of the NiCrBSi cladding layer is higher than that of the base metal. The microstructure showed good metallurgical bonding between NiCrBSi cladding and substrate had been achieved. In addition, directionally solidified microstructures were deposited. From the top to bottom of the cladding layer, the microstructures are, in order, equiaxed crystal, dendrite crystal, cellular crystal, columnar crystal and plane crystals. The corrosion resistance of the base metal and specimens manufactured by laser-high frequency induction hybrid cladding were evaluated in 3.5% NaCl solution by electrochemical testing. The experimental results demonstrate that the corrosion resistance of the NiCrBSi cladding layer fabricated by laser-high frequency induction hybrid cladding technology is better than the base metal.

Development of Laser Cladding Materials with Crack Resistance and Wear Resistance in Clad Layer of Grey Iron

Crack resistance and wear resistance of laser clad layer on the surface of cast iron

A Study on the Wear Resistance of Laser Cladding Layers on Grey Iron

Effect of Cu-Ni-V-C Alloy on Properties of Laser Clad Layer

The Effect of TiC-Fe3C on the Wear Resistance of Laser Cladding Layers in Grey Iron

Microstructure and Wear Resistance of Ductile Cast Iron Laser Clad with Ni-Ti-Co-C

Properties of Laser-Clad Stainless Steel–Ni/WC Double-Layer Coatings

Numerical Optimization and Performance Study of Ni-Based Coatings on Gray Cast Iron Surface by High-Speed Laser Cladding Based on Orthogonal Test

Study of the effect of overlap rate on the failure form, microstructure and wear resistance of multilayer laser cladding on grey cast iron surfaces

Microstructural evolution and corrosion properties of Ni-based alloy coatings fabricated by multi-layer laser cladding on cast iron

Study of the Microstructure and Corrosion Properties of a Ni-Based Alloy Coating Deposited onto the Surface of Ductile Cast Iron Using High-Speed Laser Cladding

Microstructure and corrosion-wear behaviors for laser cladding repaired martensitic stainless steels using Co-based and Ni-based powders

Research on Laser Cladding Co-Based Alloy on the Surface of Vermicular Graphite Cast Iron

Study of Cracking Mechanism and Wear Resistance in Laser Cladding Coating of Ni-based Alloy

Investigation of Preparation Processes and Corrosion Resistance of Nicrbsi Coatings Fabricated by Laser-High Frequency Induction Hybrid Cladding

The microstructure evolving and element transport of Ni-based laser-cladding layer in supercritical water

Elimination of voids by laser remelting during laser cladding Ni based alloy on gray cast iron

Microstructure, Phase Constituents and Wear Behavior of Fe/Ni-based Laser Clad Layers

Laser Cladding Ni35A120Fe Intermetallic Coating for Resisting High-Temperature Oxidation and Hot Corrosion

TiC Reinforcement Composite Coating Produced Using Graphite of the Cast Iron by Laser Cladding

Repair feasibility and performance enhancement analysis of Fe-based alloy coating on ductile iron surface by high-speed laser cladding