Abstract:Abstract Nickel-based alloy coatings were widely used for the remanufacturing of dies and moulds by laser cladding, but the crack sensitivity would be increase due to the higher strength and hardness, which reduced the wear resistance of Ni-based alloys. In this paper, Ni-based coatings with the addition of a plastic phase (an austenitic stainless net) were prepared using laser cladding technology, and the CeO 2 was added in cladding layers. The cracking mechanism, microhardness, microstructure, phase composition, and wear properties were investigated. The relationship between thermal stress and the elastic and plastic fracture had been developed from the standpoint of fracture mechanics and thermal elastic fracture mechanics. The fracture criterion of the nickel-based coating was obtained, and the study has shown that the crack sensitivity could be reduced by decreasing the thermal expansion coefficient Δ α . Thus, a new method was proposed, which the stainless steel nets were prefabricated on the substrate. It was found that the number of cracks reduced significantly with the addition of stainless steel net. When the stainless steel net with 14 mesh was added in Ni-based coatings, the average microhardness of nickel composite coating was 565 HV 0.2 , which was 2.6 times higher than that of the 45 steel substrate. Although the rare earth oxide 4 wt.% CeO 2 and stainless steel net were added in the Ni-based coating reducing the microhardness (the average microhardness is 425 HV 0.2 ), the wear resistance of it improved substantially. The wear volume of Ni-based composite coating was 0.56×10 −5 mm 3 ·N −1 ·m −1 , which was 85.1% lower than that of 45 steel. The experiment results have shown that the Nickel-based composite coating is equipped with low crack sensitivity and high abrasive resistance with austenitic stainless net and the rare earth oxide 4 wt.% CeO 2 . This research offers an efficient solution to produce components with low crack susceptibility and high wear-resistance coatings fabricated by laser cladding.

Effect of Cu-Ni-V-C Alloy on Properties of Laser Clad Layer

Development of Laser Cladding Materials with Crack Resistance and Wear Resistance in Clad Layer of Grey Iron

Crack resistance and wear resistance of laser clad layer on the surface of cast iron

Research on Laser Cladding Co-Based Alloy on the Surface of Vermicular Graphite Cast Iron

Effect of Copper on Microstructure and Performance of WC/NiAl/TiC Composite Coatings by Laser Cladding

Effect of Laser Cladding Layers on Microstructure and Mechanical Properties of NiCoCrAlY Bond Coat

Study of Cracking Mechanism and Wear Resistance in Laser Cladding Coating of Ni-based Alloy

Microstructure and wear behavior of laser clad interstitial CoCrFeNi high entropy alloy coating reinforced by carbon nanotubes

Experimental Research on Cracking Behavior During High-Power CO 2 Laser Cladding

Effect of Ultrasonic Vibration Frequency on Ni-Based Alloy Cladding Layer

Microstructures and Properties of Laser-Clad in Situ Particle Reinforced Ni-Base Composite Coating on 55mn Steel

Effect of process parameters and niobium carbide addition on microstructure and wear resistance of laser cladding nickel‐based alloy coatings

Microstructure, microhardness and corrosion resistance of laser cladding Ni–WC coating on AlSi5Cu1Mg alloy

Microstructures and properties of nano-modified multimodal Cr3C2-NiCr coatings made through laser cladding

Comparative investigation on microstructures and properties of WC/Cr 3 C 2 reinforced laser cladding Ni-based composite coatings subjected to ultrasonic impact treatment

Research on Microstructure Properties of the TiC/Ni-Fe-Al Coating Prepared by Laser Cladding Technology

Microstructure and tribological performance of novel Ni-based alloy cladding with excellent high temperature wear resistance and self-lubrication performance

Study on the microstructure and properties of a laser cladding Fe–Ni–Al coating based on the invar effect

Influence of Cu Content Variation on the Tribological Properties of Ni60CuMo with Sandwich-Structured Composite Coatings by Laser Cladding

Microstructure and Mechanical Properties of Ni-Based Alloy Composite Coating on Cr12MoV by Laser Cladding

Microstructural and Performance Analysis of (TiAl)95−xCu5Nix Coatings Prepared via Laser Surface Cladding on Ti–6Al–4V Substrates