Abstract:Morphologies and viscoelastic behavior of high density polyethylene/nylon 6 (HDPG/PA6) blends compatibilized by maleic anhydride grafted high density polyethylene (HDPE-g-MAH) were studied through observation of scanning electron microscope(SEM) and dynamic rheological testing. It is found that HDPE-g-MAH can efficiently enhance the compatibility between PA6 and HDPE and improve the dispersion of PA6 and the interfacial state of phases due to in situ forming of graft copolymer (HDPE-g-PA6). Such improvement appears more obviously with the increasing of HDPE-g-MAH content when the concentration of HDPE-g-MAH is below 20 wt%. Hence,change of HDPE-g-PA6 amount also results in corresponding variations of linear viscoelastic behavior for the blends. The zero shear viscosity of blends increases with the addition of HDPE-g-MAH and approaches invariablenes with 20 wt% HDPE-g-MAH. At low frequency region the dependence of storage modulus on frequency for the blends lends to be weakened with the increase of HDPE-g-MAH concentration and begins to show "second plateau" with 10 wt% HDPE-g-MAH. These phenomena reflect macromolecular-chains entanglement enhancement clue to HDPE-g-PA6 forming. Both changes in morphologies and viscoelastic behavior for blends are ascribed to formation of HDPE-g-PA6. Compared with SEM observation, dynamic rheological testing gives much information about interface and interaction between macromolecular-chains. It is suggested that structure evolution with increase of HDPE-g-MAH content for HDPE/PA6 blends can be characterized preferably by using dynamic rheological measurements.

Morphologies and Properties of PVC/Nylon Terpolymer Blends

Properties and morphologies of PVC/nylon terpolymer blends

Rheological Properties of PET/PA66/Liquid Crystalline Copolyesteramide Blends

Morphology and Mechanical Properties of Nylon 6/PBT Blends Compatibilized with Styrene/Maleic Anhydride Copolymer

Morphology and mechanical properties of poly(vinyl chloride)/nano-hydrotalcite composites

Effect of Compatibilizer on Morphology and Properties of HDPE/Nylon 6 Blends

Morphology, rheology, and mechanical properties of polylactide/ poly(ethylene-co-octene) blends

Effect of Dynamic Vulcanization on Properties and Morphology of Nylon/San/Nbr Blends: A New Compatibilization Method of Nylon/Abs Blends

Effect of Compatibilizer and Nucleation Agent on the Properties of Poly(lacticacid)/Polycarbonate (PLA/PC) Blends

In-situ Compatible Composite of Nylon 66 and Thermotropic Liquid Crystalline Polyamide

MORPHOLOGICAL EVOLUTION AND VISCOELASTIC BEHAVIOR OF COMPATIBILIZED HDPE/PA6 BLENDS

Miscibility, Phase Behavior, and Mechanical Properties of Ternary Blends of Poly(vinyl Chloride)/polystyrene/chlorinated Polyethylene-Graft-polystyrene

Compatibilization And Toughening Of Immiscible Ternary Blends Of Polyamide 6, Polypropylene (Or A Propylene-Ethylene Copolymer), And Polystyrene

Structure and Properties of Poly(vinyl Chloride)/halloysite Nanotubes Nanocomposites

Effects of Compatibilizing Agent and in Situ Fibril on the Morphology, Interface and Mechanical Properties of EPDM/nylon Copolymer Blends

Study of Compatibility Between Laminar Structure and Barrier Properties of Polyethylene/Modified Polyamide Blends

MORPHOLOGY AND MECHANICAL PROPERTIES OF NYLON-6/ABS POLYMER BLENDS COMPATIBILIZED BY STYRENE-MALEIC ANHYDIDE COPOLYMER

Morphology and Mechanical Properties of Blends of Thermoplastic Polyurethane and Polyolefins

Polyamide-reinforced ethylene-propylene-diene rubber compatibilized with chlorinated polyethylene

Influence of Methyl Methacrylate-Co-glycidyl Methacrylate Copolymers on the Compatibility, Morphology and Mechanical Properties of Poly(butylene Terephthalate) and Polycarbonate Blends

Blends of Poly(vinyl Chloride) with Acrylonitrile‐chlorinated Polyethylene‐styrene Copolymer. II. Mechanical Properties