Abstract:Carbon fiber reinforced silicon carbide ceramic matrix (C f /SiC) composites have the advantages of high temperature resistance, wear resistance, low density, high hardness as well as specific strength. They have been applied extensively in hot-end components of aerospace and braking systems of trains. Nevertheless, grappling with the anisotropy, non-homogeneity, and weak interlayer bonding of C f /SiC composites presents a major challenge for achieving efficient and low-damage processing. This paper is primarily intended to investigate comprehensively the mechanical properties and damage behavior of C f /SiC composites by nanoindentation and Vickers indentation tests. The behaviors of indentation damage on the longitudinal section of fiber (LSF), the cross-section of fiber (CSF) and matrix under different loads and the deflection mechanism of matrix crack were analyzed. The findings reveal a pronounced anisotropy between the radial and axial orientations of the fiber, and plastic deformation exists in the matrix. Furthermore, the matrix has the largest hardness and elastic modulus, while the LSF displays the lowest values among the composites. The main forms of indentation damage on the LSF are fiber crack, fiber peel off, fiber cocked up and squamous crack. The main manifestations of indentation damage on CSF are fiber crushing and fiber debonding, with the total surface damage area being comparatively limited. The fiber orientation and interface are influential factors in the crack propagation path of matrix. Notably, the fibers effectively inhibit the crack propagation of the matrix. This investigation provides valuable theoretical guidance for the formation mechanism and suppression strategy of machining damage in C f /SiC composites.

Particle Shape Effects on Ductility of Sic Particle Reinforced Ld2 Matrix Composites Investigated by Afm-Based Nanoindentation

Particle Size Effect on the Interfacial Properties of SiC Particle-Reinforced Al-Cu-Mg Composites

Effect of Particle Strength on SiCp/Al Composite Properties with Network Architecture Design

Nanoindentation Characterisation Of The Properties Around Reinforcements In A Heat Treated Spray Deposited 2014+15vol%Sicp Metal-Matrix Composite

Experiment and FEM Study on Uniaxial Tensile of SiCp/Al

Investigating Bulk Mechanical Properties on a Micro-Scale: Micro-tensile Testing of Ultrafine Grained Ni–SiC Composite to Determine Its Fracture Mechanism and Strain Rate Sensitivity

Micromechanical properties of high fracture performance SiCp–6061Al/6061Al composite

Influence of interfaces on the mechanical behavior of SiC particulate-reinforced Al–Zn–Mg–Cu composites

Further Investigation of Particle Reinforced Aluminum Matrix Composites by Indentation Experiments

In situ mechanical testing of an Al matrix composite to investigate compressive plasticity and failure on multiple length scales

Deformation Behavior of Sic Particle Reinforced Al Matrix Composites Based on Ema Model

On Understanding the Mechanical Properties and Damage Behavior of Cf/SiC Composites by Indentation Method

An Investigation of Micro-Mechanical Properties of Al Matrix in SiC/Al Composite by Indentation Experiments

Effect of Nano- and Submicron SiC on the α-Al Dendrite Size and Mechanical Strength of SiC/A356 Composites

Enhanced Mechanical Behavior and Fabrication of Silicon Carbide Particles Covered by In-Situ Carbon Nanotube Reinforced 6061 Aluminum Matrix Composites

Effects of In-Situ Carbon Layer and Volume Fraction of SiC Fiber on the Mechanical Properties and Fracture Behaviors of SiCf/SiC Composites Fabricated by a Modified PIP Method

On understanding the mechanical properties and damage behavior of C f /SiC composites by indentation method

Experimental and Numerical Investigations of Tensile Properties of SiC Particle‐Reinforced Composites

Achieving Simultaneous Enhancement of Strength and Ductility in Al Matrix Composites by Employing the Synergetic Strengthening Effect of Micro- and Nano-Sicps

Nonlinear Mechanical Behavior of High Volume Fraction Sicp/Al Alloy Composites Materials: Experimentation and Numerical Simulation

Finite Element Investigation of the Influence of SiC Particle Distribution on Diamond Cutting of SiCp/Al Composites