Abstract:Cu/SiO2 catalyst prepared by the ammonia-evaporation (AE) method is the potential preferred catalyst for hydrogenation of dimethyl oxalate (DMO) to ethylene glycol (EG). Although significant advancements have been obtained in the confirmation and influence factors of active species in the hydrogenation process, the relationship between the catalytic activity and the sensitive factors in the preparation or pretreatment process of the catalyst is still uncertain. In this paper, Cu/ZSM-5 catalysts for DMO hydrogenation to EG were prepared by the AE method using ZSM-5 molecular sieve with high silicon-alumina ratio (1500) as a support. The ZSM-5 support was pretreated by drying at 393 K for different hours and it was found that the surface hydroxyl group of the support had significant influence on the structure and catalytic hydrogenation performance of the prepared Cu/ZSM-5 catalyst. The distribution of surface hydroxyl groups could be significantly changed by pre-drying the carrier, which further resulted in the change of the copper dispersion and surface properties of subsequent copper-supported catalysts. With the decrease of hydroxyl content on the surface of the ZSM-5 support, the prepared reduced Cu/ZSM-5 catalyst possessed smaller Cu0 particles size, higher copper dispersion, higher surface area of Cu0 and Cu+ species, but weakened surface acidity of the catalyst, which resulted in the great improvement of the catalytic activity. The DMO conversion and EG selectivity could reach 100% and 93% even under the low reaction temperature at 448 K over the Cu/ZSM-5-24 catalyst (based on the ZSM-5 support pretreated by drying for 24 h). In addition, the catalytic activity did not show obvious change after 300 h of reaction, probably due to the low temperature reaction and suitable surface properties of the catalyst.Graphical Abstract

HYDROGENATION ON SUPPORTED Cu-Mn-ZnOX CATALYST--EFFECT OF PREPARATION METHOD AND REACTION CONDITIONS

Effects of Pore Structure on Methanol Selectivity in Carbon Monoxide Hydrogenation

Direct Synthesis of Dimethyl Ether on Supported Cu-Mn Catalysts

Preparation of Cu/ZnO/Al2O3 Catalysts in a Solvent-Free Routine for CO Hydrogenation

Effect of the Hydrogenation Components on Copper-Based Catalysts for Synthesis of Dimethyl Ether from CO2 Hydrogenation

DME Synthesis From CO/H<sub>2</sub> over Cu-Mn/Ă-Al<sub>2</sub>O<sub>3</sub> Catalyst

Synthesis of Dimethyl Ether on Supported Cu-Mn Catalysts

DME Synthesis From CO/H 2 over Cu-Mn/Ă-Al 2 O 3 Catalyst

Dme Synthesis From Co/H-2 Over Cu-Mn/Gamma-Al2o3 Catalyst

Influences of preparation methods of ZrO2 support and treatment conditions of Cu/ZrO2 catalysts on synthesis of methanol via CO hydrogenation

EFFECTS OF Mn ON Cu/Al2O3 CATALYSTS FOR HYDROGENATION OF CARBON MONOXIDE

Dimethyl Ether Synthesis from CO2 Hydrogenation on a CuO−ZnO−Al2O3−ZrO2/HZSM-5 Bifunctional Catalyst

Catalysis for One-step Synthesis of Dimethyl Ether from Hydrogenation of CO

Characterization of Cu-Mn/Zeolite-Y Catalyst for One-Step Synthesis of Dimethyl Ether from Co-H-2

A novel catalyst for DME synthesis from CO hydrogenation 1. Activity, structure and surface properties

Synthesis of Dimethyl Ether (DME) on Modified HY Zeolite and Modified HY Zeolite-Supported Cu–Mn–Zn Catalysts

A NOVEL PREPARETION OF Cu-Mn CATALYSTS FOR DIMETHYL ETHER SYNTHESIS FROM SYNGAS

Mechanism and catalytic performance for direct dimethyl ether synthesis by CO2 hydrogenation over CuZnZr/ferrierite hybrid catalyst

Hydrogenation of Carbon Dioxide on Cu-MnOx/Al2O3 Catalysts

Effect of Surface Hydroxyl Content of Support on the Activity of Cu/ZSM-5 Catalyst for Low-Temperature Hydrogenation of Dimethyl Oxalate to Ethylene Glycol

Role of the Cu dopant in the textural and catalytic features of the Co/ZnO catalyst for dimethyl oxalate selective hydrogenation