Elevated temperature strength of a 20 vol % ZrCp/W composite

Guiming Song,Yu Zhou,Y. J. Wang,TingChuan Lei

DOI: https://doi.org/10.1023/A:1006639606300

1998-01-01

Journal of Materials Science Letters

Abstract:null

What problem does this paper attempt to address?

Influence of Zrc Content on the Elevated Temperature Tensile Properties of Zrcp/W Composites

Yujin Wang,Hua-Xin Peng,Yu Zhou,Gui-Ming Song

DOI: https://doi.org/10.1016/j.msea.2010.11.029

2011-01-01

Abstract:The influence of ZrC content on the tensile deformation behavior and fracture strength of ZrCp/W composites in a temperature range of 800–1400°C was investigated. Both of the non-linear feature of the stress–strain curve and the rupture strain of the composites decreased with increasing ZrC content from 20 to 50vol% in all the tested temperatures. The maximum ultimate tensile strength of each ZrCp/W composite was found in the temperature range of 1000–1200°C. With increasing ZrC content from 20 to 50vol%, the maximum ultimate tensile strength of the ZrCp/W composite was decreased due to the porosity increase and the plasticity decrease of the composite although ZrC enhanced the tungsten matrix via load transferring and blocking dislocation movement in tungsten matrix.
High temperature tensile properties of 30 vol. pct ZrCp/W composite

Yujin Wang,Yu Zhou,Guiming Song,Tingquan Lei

2009-01-01

Abstract:In order to improve the high temperature strength of tungsten, 30 vol. pct ZrC particles were added to the tungsten matrix to form a 30ZrC(p)/W composite. The tensile properties from 20degreesC to 1880degreesC of the composite were examined. It was shown that with increasing testing temperature, the nonlinearity of the stress strain curve of 30ZrC(p)/W composite becames obvious over 1200degreesC and the Young's modulus decreases and the elongation increases. The ultimate tensile strength increases at first and then decreases with increasing testing temperature. The maximum strength of 431 MPa was obtained at 1000degreesC. The strengthening mechanism at high temperatures is the load transfer to ZrC particles and dislocation strengthening of the tungsten matrix with an effect of grain boundary strengthening.
Dense Submicron-Sized ZrC – W Composite Produced by Reactive Melt in Fi Ltration at 1200 ° C

Yan-Wei Zhao,Yu-Jin Wang,Hua-Xin Peng,Yu Zhou

DOI: https://doi.org/10.1016/j.ijrmhm.2011.08.009

2012-01-01

Abstract:ZrC–W composite was produced by reactive infiltration of Zr2Cu into WC preform at 1200°C. The WC reacted completely with Zr in the alloy to form 61.8vol% ZrC and 38.2vol%W. The infiltrated composite reached a relative density of 98.3% and average grains sizes of about 0.5μm. The flexural strength and the fracture toughness of the ZrC–W composite was improved by the addition of W.
Elevated Temperature Compressive Failure Behavior of a 30vol.%zrcp/w Composite

Taiquan Zhang,Yujin Wang,Yu Zhou,Tingquan Lei,Guiming Song

DOI: https://doi.org/10.1016/j.ijrmhm.2006.06.001

IF: 4.804

2007-01-01

International Journal of Refractory Metals and Hard Materials

Abstract:The elevated temperature deformation behavior of a 30vol.%ZrCp/W composite was tested on a Gleeble-1500D thermo-mechanical simulation device under a uniaxial compressive load. The micro-failure behavior of the composite is strongly affected by the adhesive strength of ZrC/W interface and the distribution of ZrC particles. The computational results by EET theory indicate that the adhesive strength of (Zr,W)C interface is higher than that of ZrC. The microcrack initiation and propagation mechanism varies with the deformation temperature. TEM results show that the initiation and propagation of the microcracks occur in three steps in 1300–1600°C.
Elevated Temperature Compressive Strength and Deformation Behavior of A Zrcp Reinforced Tungsten-Matrix Composite

Yujin Wang,Taiquan Zhang,Yu Zhou,Tingquan Lei,Guiming Song

DOI: https://doi.org/10.1166/jctn.2008.863

2008-01-01

Journal of Computational and Theoretical Nanoscience

Abstract:The elevated temperature deformation behavior of a 30 vol.%ZrC(p)/W composite was studied by hot compression. The true stress-true strain curves exhibit a steady flow characteristic. The flow stress strongly depends on temperature and strain rate. The facture strain increases with increasing temperature and decreasing strain rate. The activation energy and the stress exponent were calculated as 344 kJ/mol and 17.6, respectively. The deformation mechanisms of the composite are the dynamic recovery in tungsten matrix at temperatures under 1500 degrees C and the dynamic recrystallization in tungsten matrix at 1600 degrees C, but accompanied by a little pseudo-plasticity behavior at 1300 degrees C in the strain rate of 10(-1)similar to 1/s. The dislocation behavior in ZrC particle contributes to the plastic deformation of the composite.
Elevated temperature strength of TiCp/W composites

Yujin Wang,Yu Zhou,Guiming Song,Tingquan Lei

2009-01-01

Abstract:The elevated temperature mechanical properties of TiCp/W composites produced using powder metallurgical technique were investigated. Results show that with increasing temperature, the strength of TiCp/W composites increases gradually and reaches its maximum value at 1000 degreesC, which is much higher than that at room temperature. The strengthening mechanisms at high temperature are attributed to dislocation strengthening and load transfer between matrix and particles.
The Mechanical and Thermophysical Properties of ZrC/W Composites at Elevated Temperature

GM Song,YJ Wang,Y Zhou

DOI: https://doi.org/10.1016/s0921-5093(01)01802-0

2002-01-01

Abstract:In order to improve the elevated temperature mechanical properties and modify the thermophysical properties of tungsten, tungsten matrix composites containing 30 vol.% zirconium carbide particles (ZrC/W) were prepared by vacuum hot-pressing at 2000°C. Flexural strength of ZrC/W composites increases gradually with increasing temperature and reaches a maximum value at 1000°C. The observation of the fracture characteristics of ZrC/W composites at various temperatures reveals that the excellent elevated temperature strength is attributed to the brittle–ductile transition in the tungsten matrix, which allows a more effective strengthening effect from the zirconium carbide particles. The elastic modulus decreases slightly with increasing temperature from room temperature to 1200°C, and as a result of the addition of zirconium carbide particles the modulus of ZrC/W is higher than that of monolithic tungsten at all testing temperatures. The addition of zirconium carbide remarkably decreases the thermal conductivity of the composites. The unique combination of high melting point, good high temperature strength, high elastic modulus, and low thermal conductivity is very beneficial to the high temperature application of ZrC/W composites.
Strength properties and fracture behavior of ZrC particle-reinforced tungsten composite

Yujin Wang,Guiming Song,Qingchang Meng,Yu Zhou

IF: 3.752

2001-01-01

Transactions of Nonferrous Metals Society of China

Abstract:The flexural strength of 30% (volume fraction) ZrCparticle-reinforced tungsten composite (ZrC(p)/W) at 20 similar to 1200 degreesC were measured using three-point bending, and the fracture behaviors of the samples at 20 degreesC and 1000 degreesC were studied with a scanning electron microscope. As temperature increases, the strength of the composite increases firstly and the highest strength value, 829 MPa, is measured at 1000 degreesC, and then the strength decreases when temperature is over 1000 degreesC. The fracture of the composite at 20 degreesC, which is controlled by the crack initiating process, is brittle, and the corresponding stress-deflection curve is linear. There is a metastable growth and coalescence of the initial cracks during the fracture process of the samples at 1000 degreesC, and the stress-deflection curve displays a nonlinear characteristic, The good elevated strength of the composite is partly attributed to the W grain interior strength and ZrC(p)/W interface strength. The reinforcement at high temperature is mainly attributed to the load transfer of ZrC(p)/W interface and dislocation strengthening.
Microstructure and mechanical properties of 20Wf/30ZrCp/W composite

Yujin Wang,Yu Zhou,Guiming Song,DeSheng Lü,TingChuan Lei

2001-01-01

Abstract:The composition, microstructure and mechanical properties of 20Wf/30ZrCp/W composite produced using hot pressing technique were investigated. Results show that the relative density reaches 98.5%. The tungsten wires are well distributed within the ZrCp/W matrix with preferred orientation. There is an interdiffusion of Zr and W in ZrCp/W interface, which results in (Zr, W) C solid solution forming and a strong bond between ZrC particle and tungsten wire or tungsten. The tungsten wires are recrystallized and have no strengthening and toughening effects on ZrCp/W matrix. The strength and fracture toughness of 20Wf/ 30ZrCp/W composite are 504 MPa and 9.48 MPa·m1/2, respectively.
Elevated temperature fracture behavior of ZrC particle-reinforced tungsten matrix composite

Guiming Song,Houshan Bai,Yu Zhou,Yujin Wang

DOI: https://doi.org/10.3321/j.issn:1002-185x.2000.02.007

2000-01-01

Rare Metal Materials and Engineering

Abstract:A scanning electron microscope (SEM) was employed to study the elevated temperature (1 000 degrees C) fracture behavior of ZrC particle-reinforced tungsten composite (ZrCp/W, 30% volume fraction of ZrC particles). The results show that the fracture process at elevated temperature is "microcrack initiation-crack coalescence-quick crack propagation-material fracture". The fracture of ZrC is brittle, and the failure of matrix exhibits some ductile bears. When temperature increases, the W matrix transforms from brittle state to ductile state, and the crack propagation rate and crack sensitivity decrease, and the deformation resistance of the matrix increases. Hard ZrC in the ductile matrix inhibits ductile deformation. The brittle-ductile transition of W produces strengthening effect of the particles and dislocations in the matrix, and the elevated temperature strength is higher than room temperature strength of the ZrCp/W composite.
Ablation Properties of ZrCp/W Composites

Guiming Song,Yujin Wang,Yu Zhou,Yingkui Guo,Guangwu Wen

DOI: https://doi.org/10.3321/j.issn:1002-185x.2001.02.006

2001-01-01

Rare Metal Materials and Engineering

Abstract:The ablation properties of ZrCp/W composite were measured using a self-made oxyocetylene ablation equipment. The results indicate that the values of mass ablation rate and linear ablation rate are in the order of W > 30vol%ZrCp/W > 40vol% ZrCp/W. The ablation resistance of the composites greatly increases with increasing ZrC particle content. The important ablation surface temperature curves were detected in situ using a multi-wavelength pyrometer. Thermochemical oxidation of ZrC and W is the main ablation mechanism of ZrCp/W composites.
Microstructures and Mechanical Properties of ZrCP/W Composites at Room Temperature

Guiming Song,Yujing Wang,Yu Zhou,Yi Sun

DOI: https://doi.org/10.3321/j.issn:1002-185x.2001.06.011

2001-01-01

Rare Metal Materials and Engineering

Abstract:The microstructures of ZrC particle-reinforced tungsten matrix composite (ZrCp/W, 30vol%ZrC particles) have been investigated using XRD, SEM and TEM. The experimental results indicate that the ZrC particles inhabit the growth of tungsten grains during sintering. The relative density of the composite is less than that of monolithic tungsten. W atoms diffuse in the lattice of ZrC, resulting in a formation of (Zr, W)C solid solution in ZrC particles, and a little of Zr diffuse in W lattice, resulting in a metallurgical bonding of ZrC particles to W matrix. W2C and ZrO2 phases were found rarely in the composites. At room temperature , the fracture toughness, elastic modulus and hardness of the composite increase, because of the additive ZrC particles, but the flexural strength of the composite is lower than that of monolithic tungsten. The toughening mechanisms of ZrCp/W composite are crack deflection and grain refining.
Thermal diffusivity and thermal conductivity of ZrCp/W composites

Yu Zhou,Yujin Wang,Guiming Song,Tingquan Lei,Zhiheng Huang

2003-01-01

Abstract:Thermal diffusivity of ZrCp/W composites and its dependence on temperature and ZrCp content are reported. Measurements were carried out from 20 degreesC to 800 degreesC with the ZrCp volume fraction varied from 0% to 40% using a laser-flash method. Also, the thermal conductivity was calculated as the product of density, specific heat and thermal diffusivity. The results show that the thermal conductivity of ZrCp/W composites changes slightly with increasing temperature but decreases with increasing volume fraction of ZrCV. The theoretical values of thermal conductivity of ZrCp/W composites are much higher than their measured ones. The ZrCp content dependence of all other thermophysical properties (thermal diffusivity, thermal conductivity, density and specific heat) is also presented.
High Temperature Electrical Resistivities of Zrc Particle-Reinforced Tungsten-Matrix Composites

Taiquan Zhang,Yujin Wang,Yu Zhou,Guiming Song

DOI: https://doi.org/10.1016/j.ijrmhm.2010.02.007

2010-01-01

Abstract:High temperature electrical resistivities of ZrCp/W composites prepared by hot-pressing had been continuously tested in a temperature range of RT–900°C. A semi-theoretical model for predicting the effect of microstructure, ZrC particle content, and temperature on electrical resistivities of ZrCp/W composites was proposed by decomposing a basic unit of particle–reinforced metal-matrix composites (PMMC) into the basic series and parallel circuits of metal-matrix and particle. Experimental high temperature electrical resistivities of ZrCp/W composites agree well with the theoretical prediction.
Effect of Heat Treatment on Microstructure and Mechanical Properties of ZrC Particles Reinforced Tungsten-Matrix Composites

Taiquan Zhang,Yujin Wang,Yu Zhou,Guiming Song

DOI: https://doi.org/10.1016/j.msea.2009.01.078

IF: 6.044

2009-01-01

Materials Science and Engineering A

Abstract:A 20vol.% ZrCp/W composite is fabricated by hot-pressing, and its mechanical properties can be significantly improved by the addition of ZrC particles. On the other side, the residual pores within ZrC particles clustering regions which are some latent microcrack sources are mainly caused by the relative low sinterability of ZrC particles. In order to eliminate the pores within the particle clusters, the as-sintered composite is annealed at 2300°C for 1h. The microstructure of the annealed composite becomes more uniform and densified. Components of the as-sintered and annealed composites are composed of a dilute solid solution tungsten-matrix, (Zr, W)C solid solution particles and a new W2C phase, but the content of W2C phase in the annealed composite increases. After annealing, the strength properties of the composite decrease, but its plasticity increases.
Compressive Deformation Behavior of a 30 Vol.%zrcp/w Composite at Temperatures of 1300–1600 °C

Taiquan Zhang,Yujin Wang,Yu Zhou,Tingquan Lei,Guiming Song

DOI: https://doi.org/10.1016/j.msea.2007.04.024

2008-01-01

Abstract:The compressive deformation behavior of a 30vol.%ZrCp/W composite was investigated in a temperature range of 1300–1600°C. The true stress–strain behavior of the composite is strongly influenced by the deformation temperature and the strain rate. The serrated character of the true stress–strain curves is mainly due to the initiation, propagation and closure of microcracks in ZrC particle agglomerates during compressive deformation. The deformation mechanisms at the tested temperature range of 1300–1600°C are the dislocation movement in the tungsten grains, slip along the W and ZrC grain boundaries as well as along ZrC/W interfaces. The dynamic recovery in the tungsten matrix is detected at the temperatures of 1300–1500°C. The dynamic recrystallization occurs when the temperatures is above 1500°C. The dislocation behavior in ZrC particles is also studied.
Thermophysical Properties of ZrCp/W Composites Prepared by Hot-pressing

王玉金,宋桂明,周玉,雷廷权

DOI: https://doi.org/10.3321/j.issn:1001-3784.2002.05.001

2002-01-01

Abstract:Zirconium carbide particle-reinforced tungsten matrix (ZrCp/W) composites were fabricated by hot-pressing technique. The effects of temperature and ZrCp content on the thermophysical properties of the composites were investigated. The results show that with the increase of temperature, the specific capacity and the coefficient of thermal expansion increase monotonically, the thermal conductivity increases slightly. The specific capacity and the coefficient of thermal expansion of the ZrCp/W composites increase with ZrCp content increasing, which is in accord with the mixture rule. The thermal conductivity of the ZrCp/W composites, which are sensitive to microstructure of the composites, decrease greatly with ZrCp content increasing. The experimental results of the thermal conductivity are considerably lower than the predicted ones, which mainly due to the diffraction effect of the defects like grain boundary and pores on thermal conducting-particles.
Elevated Temperature Mechanical and Thermophysical Properties of Titanium Carbide Particle-Reinforced Tungsten Composites

GM Song,YJ Wang,Y Zhou,TC Lei

DOI: https://doi.org/10.1068/htrt170

1999-01-01

Abstract:An investigation on the elevated temperature mechanical properties and thermophysical properties of 30 vol% titanium carbide particle-reinforced tungsten matrix (TiCp/W) composites produced by a powder metallurgical technique shows that with increasing temperature, the strength of the TiCp/W composites increases gradually and reaches a maximum value at 1000 degrees C, which is much higher than that at room temperature. The elastic modulus decreases slightly with a rise of temperature from room temperature to 1200 degrees C, and the linear expansion varies linearly with temperature. The elevated strength, density, modulus, and coefficient of thermal expansion of TiCp/W composites makes them suitable for the manufacture of counterbalances in combustion motors for use at high temperature.
Effect of ZrC Particle Size on Microstructure and Room Temperature Mechanical Properties of ZrCp/W Composites

Taiquan Zhang,Yujin Wang,Yu Zhou,Guiming Song

DOI: https://doi.org/10.1016/j.msea.2010.03.008

2010-01-01

Abstract:Tungsten composite reinforced by 20vol.% ZrC particles with three different mean particle size (1.25, 1.71 and 5.78μm) were prepared by hot-pressing at 2200°C, 25MPa for 1h. The effect of ZrC particle size on microstructure and room temperature mechanical properties is investigated by examining the ZrC particle distribution, pore in the particle clusters, and composition of the ZrC/W interface and strength of the composites. The results show that a small amount of tiny pores existed in the ZrC particle clusters with a mean size of 1.25μm, and the larger pores was observed when the mean size was 5.78μm. (Zr,W)C solid solution was found at the ZrC/W interface, and W2C phase formed when the ZrC particle size was less than about 1.71μm. The flexural strength of the ZrCp/W composite is deteriorated by the ZrC particle clusters and the defects within the ZrC particles. The highest strength of 1210MPa was tested on the composite containing 1.71μm ZrC particles.
Novel low temperature derived W f /W-ZrC-Cu composites by reactive infiltration with enhanced mechanical and thermal physical properties

Dong Wang,Yaning Zhang,Kai Xu,Boxin Wei,Xiang Ding,Xing Jin,Songlin Ran

DOI: https://doi.org/10.1016/j.jmrt.2023.05.048

IF: 6.267

2023-05-11

Journal of Materials Research and Technology

Abstract:W f /W-ZrC-Cu composites with densities over 95% have been prepared by infiltrating Zr-Cu binary molten alloys into porous W f /W+WC preforms at 1200−1400 °C. The hybrid strengthening of in-situ formed ZrC particles, and the addition of continuous W f have made the composites improved flexure strength and fracture toughness of 612 MPa and 10.41 MPa·m 1/2 , respectively. The residual Cu provided a moderate interface between W f and W-ZrC matrix, which was beneficial to improved fracture energy of 2-3·10 3 J·m -2 and thermal conductivity of over 80 W·(m·K) -1 . The W f impeded cracks and new surfaces to the ultra-high temperature air plasma torch. The composites thus possess superior thermal shock resistance, and the linear and mass ablation rates reduced to 0.40 mm·s -1 and 0.0112 g·s -1 , respectively. This study provides a novel approach for the fabrication of refractory fiber reinforced refractory metal/carbide based composites with excellent comprehensive properties at relatively low temperatures.

materials science, multidisciplinary,metallurgy & metallurgical engineering

Elevated temperature strength of a 20 vol % ZrCp/W composite

Influence of Zrc Content on the Elevated Temperature Tensile Properties of Zrcp/W Composites

High temperature tensile properties of 30 vol. pct ZrCp/W composite

Dense Submicron-Sized ZrC – W Composite Produced by Reactive Melt in Fi Ltration at 1200 ° C

Elevated Temperature Compressive Failure Behavior of a 30vol.%zrcp/w Composite

Elevated Temperature Compressive Strength and Deformation Behavior of A Zrcp Reinforced Tungsten-Matrix Composite

Elevated temperature strength of TiCp/W composites

The Mechanical and Thermophysical Properties of ZrC/W Composites at Elevated Temperature

Strength properties and fracture behavior of ZrC particle-reinforced tungsten composite

Microstructure and mechanical properties of 20Wf/30ZrCp/W composite

Elevated temperature fracture behavior of ZrC particle-reinforced tungsten matrix composite

Ablation Properties of ZrCp/W Composites

Microstructures and Mechanical Properties of ZrCP/W Composites at Room Temperature

Thermal diffusivity and thermal conductivity of ZrCp/W composites

High Temperature Electrical Resistivities of Zrc Particle-Reinforced Tungsten-Matrix Composites

Effect of Heat Treatment on Microstructure and Mechanical Properties of ZrC Particles Reinforced Tungsten-Matrix Composites

Compressive Deformation Behavior of a 30 Vol.%zrcp/w Composite at Temperatures of 1300–1600 °C

Thermophysical Properties of ZrCp/W Composites Prepared by Hot-pressing

Elevated Temperature Mechanical and Thermophysical Properties of Titanium Carbide Particle-Reinforced Tungsten Composites

Effect of ZrC Particle Size on Microstructure and Room Temperature Mechanical Properties of ZrCp/W Composites

Novel low temperature derived W f /W-ZrC-Cu composites by reactive infiltration with enhanced mechanical and thermal physical properties