Abstract:Cu matrix composites have received increased attention in a wide industrial area because of their excellent mechanical properties and good electrical and thermal conductivity. However, the addition of general ceramic reinforcements often leads to a marked reduction in electrical conductivity for Cu matrix composites. In this study, the ZrB 2 -reinforced Cu composites have been developed to overcome this drawback since these metal borides possess relatively high electrical conductivity. The 5 wt.% ZrB 2 /Cu composites were prepared using hot-pressed sintering techniques at varying temperatures from 760 to 920°C. The influence of sintering temperature on the microstructure, relative density, and mechanical and electrical properties was examined. The results of the SEM observation show that ZrB 2 particles are seamlessly integrated into the Cu matrix for all ZrB 2 /Cu composites. The average grain size of the Cu matrix increases from 360 to 980 nm with the increase of the sintering temperature. The increase in sintering temperature also leads to the surface porosity decrease from 1.4 to 0.4%. The relative density and electric conductivity of the composites increase at the same time as the sintering temperature increases. However, microhardness increases and decreases, with a maximum value of 92 HV0.2 achieved at 840°C. The elastic modulus and nanohardness maps determined from the nanoindentation indicate that the reinforced ZrB 2 particles demonstrate the highest values for elastic modulus (340–500 GPa) and nanohardness (30–48 GPa). At the same time, the Cu matrix possesses a modulus of 100–200 GPa and nanohardness of about 10 GPa. TEM observation confirmed that the sintering temperature exhibits little influence on the interface reaction between ZrB 2 and Cu. Both sharp interface and interface with amorphous transition layer are observed. The variation of microhardness is mainly due to the strengthening of grain refinement and to the mismatch of the thermal expansion coefficients. The above results can provide further insights into the deeper understanding of the role of sintering temperature during hot-pressed sintering.

High temperature tensile properties of 30 vol. pct ZrCp/W composite

Influence of Zrc Content on the Elevated Temperature Tensile Properties of Zrcp/W Composites

High Temperature Tensile Properties of in Situ TiBw/Ti6Al4V Composites with a Novel Network Reinforcement Architecture

Dense Submicron-Sized ZrC – W Composite Produced by Reactive Melt in Fi Ltration at 1200 ° C

Mechanical Properties and Thermal Shock Performance of W-Y2O3composite Prepared by High-Energy-rate Forging

Enhancing High-Temperature Wear Resistance by Constructing the Amorphous-Crystal Heterointerface Structure in WO3/TiO2 Composite Coatings

High‐temperature tensile strength and fracture behavior of ZrB2‐SiC‐graphite composite

Novel low temperature derived W f /W-ZrC-Cu composites by reactive infiltration with enhanced mechanical and thermal physical properties

High temperature oxidation resistance of hot-pressed h-BN/ZrO 2 composites

DBTT and tensile properties of as-sintered tungsten alloys reinforced by yttrium-zirconium oxide

Effect of different crystal forms of ZrO 2 on the microstructure and properties of tungsten alloys

The High Thermal Stability Induced by a Synergistic Effect of ZrC Nanoparticles and Re Solution in W Matrix in Hot Rolled Tungsten Alloy

High temperature fracture mechanism of ultrafine WC-Co cemented carbides containing (Ti,W)C

Deformation behavior and microstructure evolution of TZM alloy with 1.0 wt%ZrO 2 under high temperature compression

Microstructure and high-temperature mechanical properties of Cu-W composite prepared by hot isostatic pressing

Influence of Zr Microalloying on the Microstructure and Room-/High-Temperature Mechanical Properties of an Al–Cu–Mn–Fe Alloy

Effect of Sintering Temperature on the Microstructure and Properties of High-Strength and Highly Conductive 5 wt.% ZrB2/Cu Composite

Mechanical properties and fracture behavior of ultrahigh temperature ceramics at ultrahigh temperatures

Effects of ZrC content on the microstructure and mechanical property of ZrC/ZTA composites consolidated by hot pressing

Effect of Tungsten Carbide Additions on the Microstructure, Mechanical, and Tribological Properties of M2 High-Speed Steel Matrix Composites

Microstructure evolution and hot deformation behavior of Cu−3Ti−0.1Zr alloy with ultra-high strength