Resistivity controlled by SiC whisker orientation in Si3N4 matrix composites

ChangAn Wang,Yong Huang,Ying Li,Zhongtai Zhang,Zhipeng Xie,Jianbao Li

DOI: https://doi.org/10.1023/A:1006694624530

1998-01-01

Journal of Materials Science Letters

Abstract:null

What problem does this paper attempt to address?

Roles of orientation relationship and recrystallization in superplasticity of SiCw/6061Al composite

Wanli Gu,Huaxin Peng,Zongrong Liu,Dezun Wang,ZhongKai Yao

IF: 3.752

1997-01-01

Transactions of Nonferrous Metals Society of China

Abstract:The orientation relationship between different aluminium grains as well as that between the aluminium and the whisker during the superplastic deformation have been studied. In addition, the relation between recrystallization and orientation were examined. The results showed that during the superplastic deformation the orientation relationship between different aluminium grains and that between the aluminium and the whisker were unstable. There was also no definite orientation between the recrystal grains emerging in the process of superplastic deformation and the whisker. Only the recrystal grain produced in the end of deformation could keep definite orientation with the whisker. The recrystallization induced by superplastic deformation could coordinate the sliding of grain boundaries and the interfaces.
Processing and Properties of Oriented SiC Whisker-Reinforced Si3N4 Ceramic Matrix Composites

Yong Huang,ChangAn Wang

1999-01-01

Key Engineering Materials

Abstract:Whisker orientation is one of key factors affecting whisker toughening mechanisms. By extrusion, SiC(w)/Si3N4 composites with nearly 1-dimensional oriented alignment of whiskers were prepared. The results showed that whisker orientation had a dramatic influence on strength and toughness of the composites. Especially, along the direction of whisker oriented alignment, as great as 200MPa and 3MPa·m1/2 improvements in bending strength and fracture toughness of SiC(w)/Si3N4 composites were obtained respectively. Through analyzing the fractographs in the different whisker orientation of the composites, the effects of whisker orientation on toughening mechanisms were discussed. The results showed that effects of whisker reinforcing and toughening could be improved simultaneously through whisker oriented alignment.
The effect of whisker orientation in SiC whisker-reinforced Si3N4 ceramic matrix composites

Wang Chang-an,Huang Yong,Zhai Hongxiang

DOI: https://doi.org/10.1016/S0955-2219(98)00289-1

IF: 5.7

1999-01-01

Journal of the European Ceramic Society

Abstract:Si3N4 ceramic matrix composites reinforced by nearly unidirectionally aligned SiC whiskers have been prepared by extrusion and hot pressing. Unlike the case in traditional Si3N4 ceramic matrix composites reinforced by random SiC whiskers, the mechanical properties of the composites exhibit a significant dependence on whisker orientation. In the direction of whisker alignment for SiC(w)/Si3N4 composites, increments in bending strength and fracture toughness of 200MPa and 3MPa·m1/2 are obtained respectively, compared to the values in the direction perpendicular to whisker alignment. Based on microscopic fractographic observation and micromechanics analyses, the effects of whisker orientation on toughening mechanisms are discussed. The results indicate that the whisker orientation, θ, is a decisive factor for the essential toughening mechanisms of whiskers. Only in the case of small θ and weak interface can whisker pullout occur, and whisker has maximum toughening effect. The results show that effects of whisker strengthening and toughening can be improved simultaneously through whisker oriented alignment. ©
Mechanical Behavior of SiCf/SiC Composites with Alternating PyC/SiC Multilayer Interphases

Haijiao Yu,Xingui Zhou,Wei Zhang,Huaxin Peng,Changrui Zhang

DOI: https://doi.org/10.1016/j.matdes.2012.07.073

2013-01-01

Abstract:In order to tailor the fiber-matrix interface of continuous silicon carbide fiber reinforced silicon carbide (SiCf/SiC) composites for improved fracture toughness, alternating pyrolytic carbon/silicon carbide (PyC/SiC) multilayer coatings were applied to the KD-I SiC fibers using chemical vapor deposition (CVD) method. Three dimensional (3D) KD-I SiCf/SiC composites reinforced by these coated fibers were fabricated using a precursor infiltration and pyrolysis (PIP) process. The interfacial characteristics were determined by the fiber push-out test and microstructural examination using scanning electron microscopy (SEM). The effect of interface coatings on composite mechanical properties was evaluated by single-edge notched beam (SENB) test and three-point bending test. The results indicate that the PyC/SiC multilayer coatings led to an optimum interfacial bonding between fibers and matrix and greatly improved the fracture toughness of the composites. (C) 2012 Elsevier Ltd. All rights reserved.
Complex Impedance Analysis on the Orientation Effect of Whiskers in Oriented Silicon Carbide Whisker/Silicon Nitride Composites

CA Wang,Y Huang,ZP Xie,Y Li,ZT Zhang

DOI: https://doi.org/10.1111/j.1151-2916.2000.tb01617.x

IF: 4.186

2000-01-01

Journal of the American Ceramic Society

Abstract:The effect of whisker orientation on the electrical properties of SiCw/Si3N4 composites was investigated, using the principle of complex impedance. The impedance spectra of the composites exhibited significant dependence on whisker orientation. Based on the experimental results and the microstructure of the composites, the impedance mechanisms were discussed and a corresponding equivalent‐circuit model was presented, which agreed well with the experiments.
The properties of the multi-node SiCw and its reinforced Si 3N4 ceramic composite material

Qibao Wang,Minfang Han,Mengxiong Guo

2005-01-01

Xiyou Jinshu Cailiao Yu Gongcheng/Rare Metal Materials and Engineering

Abstract:SiC whisker (SiCw) was synthesized from rice hulls in the presence of nonmetallic catalyst, and its morphology and crystal structure were investigated by means of TEM and XRD. The mechanical properties of the SiC w reinforced Si3N4 ceramic composite were determined and studied. The results indicate that the yield of the SiC w is over 30%, the morphology of the SiCw is straight with rough surface and multi-node. Spacing between the nodes falls into the range of 0.5 μm ∼1.Sμm, the diameter distribution, length distribution and distribution of length/diameter ration are 0.53±0.28nm, 10.3±6.1pm and 23.1±18.3, respectively. The crystalline phase of the SiC w is mainly β type with slight quantity α-SiC polytype. Every two contiguous whisker nodes represent in the form of twin crystals. The rough surface of the whisker with multi-node results in the increase of the contacting area and friction effects between the whisker and matrix, and consequently enhances the "bridged linkage" strength of the whiskers in matrix. The quality indices of Si3N4 ceramic composite materials reinforced with the SiCw are 856±22 MPa of δfRT, 418.5±14.2 MPa of δ f 1 300°c and 11.3±1.0 MPa·m 1/2 of KIC.
The Dual Effect Of Whiskers On Toughening And Conducting Properties In Aligned Sic Whisker-Reinforced Si3n4-Matrix Composites

Y Huang,Ca Wang,Jb Li,Zp Xie

1998-01-01

Abstract:SiC whisker-reinforced Si3N4 composites were prepared by different processes. It was found that an increase in degree of whisker alignment greatly improved the strength and toughness of the composites in the alignment direction. On the other hand, the experiments showed that aligned whiskers could also improve the electrical conductivity of the composites. The higher the degree of whisker alignment, the better the conductivity of the composites in the alignment direction. The dual effect of whiskers, by acting both as a reinforcement and as an electrical element, make it possible to diagnose and detect the change of microstructure in the composites. Using this approach may provide a scientific basis for developing intelligent ceramics in the future.
The properties of the multi-node SiCw and its reinforced Si3N4 ceramic composite material

QB Wang,MF Han,MX Guo

DOI: https://doi.org/10.3321/j.issn:1002-185X.2005.z1.100

2005-01-01

Rare Metal Materials and Engineering

Abstract:SiC whisker (SiCw) was synthesized from rice hulls in the presence of nonmetallic catalyst, and its morphology and crystal structure were investigated by means of TEM and XRD. The mechanical properties of the SiCw reinforced Si3N4 ceramic composite were. determined and studied. The results indicate that the yield of the SiCw is over 30%, the morphology of the SiCw is straight with rough surface and multi-node. Spacing between the nodes falls into the range of 0.5 mu m similar to 1.5 mu m, the diameter distribution, length distribution and distribution of length/diameter ration are 0.53 +/- 0.28 mu m, 10.3 +/- 6.1 mu m and 23.1 +/- 18.3, respectively. The crystalline phase of the SiC. is mainly 8 type with slight quantity alpha-SiC polytype. Every two contiguous whisker nodes represent in the form of twin crystals. The rough surface of the whisker with multi-node results in the increase of the contacting area and friction effects between the whisker and matrix, and consequently enhances the "bridged linkage" strength of the whiskers in matrix. The quality indices Of Si3N4 ceramic materials reinforced with the SiCw are 856 +/- 22 MPa of delta(RT)(f), 418.5 +/- 14.2 MPa of delta(1300 C)(f) and 11.3 +/- 1.0 MPa.m(1/2) of K-IC.
Improved Resistance to Damage of Silicon Carbide-Whisker-Reinforced Silicon Nitride-Matrix Composites by Whisker-Oriented Alignment

Chang-an Wang,Yong Huang,Zhipeng Xie

DOI: https://doi.org/10.1111/j.1151-2916.2001.tb00624.x

IF: 4.186

2001-01-01

Journal of the American Ceramic Society

Abstract:The effects of whisker-oriented alignment on resistance to damage of SiC(w)/Si3N4 composites have been investigated by the Vickers indentation method and R-curve behavior. It is shown that increasing the degree of whisker-oriented alignment decreases the lengths of Vickers Impressions and indentation cracks. The results exhibit rising R-curve behaviors for the SiC(w)/Si3N4 composites with different degree of whisker-oriented alignment. Moreover, the initial crack length c(i), the threshold of crack growth resistance K-i, and the upper bound of crack growth resistance K-infinity change regularly with increasing degree of whisker-oriented alignment. All results suggest that the whisker-oriented alignment improves the resistance to damage of the composites, resulting in a more reliable and usable composite.
Influence of Reinforcement with Multimodal Distribution on Thermophysical Properties and Fracture Behavior in Al-Si/SiC Composites Infiltrated under Super-Gravity Field

Penghui Zhang,Chuandong Wu,Yuehui Lu,Zhanghua Gan,Guoqiang Luo,Jing Liu

DOI: https://doi.org/10.1016/j.jallcom.2024.174775

IF: 6.2

2024-01-01

Journal of Alloys and Compounds

Abstract:Super-gravity field assisted infiltration is reported as an effective method to obtain the nearly fully-dense Al-Si/SiC composites at relatively lower temperature, which inhibit the interfacial reaction and result in the enhancement of thermal conductivity (TC) and bending strength (BS). Currently, SiC reinforcement with multimodal distribution was designed to further enhance the TC and BS with lower coefficient of thermal expansion (CTE) of Al-Si/SiC composites. For the composites with monomodal SiC distribution, enlarging the size of SiC results in an enhancement of TC with the sacrifice of BS. Interestingly, for the composites with multimodal SiC distribution, the TC can be stabilized within an extended range (175-187W/m·K at 373K) with reduced CTE and higher BS. When the large to small size ratio was 1:2, the optimal comprehensive properties (CTE: 8.66×10-6K-1 ranged from 323 to 373K, TC: 179.2W/m·K at 373K, BS: 309 ± 9MPa) can be obtained. Hasselman-Johnson, Turner, and Kerner models are established to better understand the thermophysical properties, while the fracture behavior is discussed based on the track of crack propagation.
Improved Sinterability of SiC(w)/Si3N4 Composites by Whisker-Oriented Alignment

Ca Wang,Y Huang

DOI: https://doi.org/10.1016/j.msea.2004.08.032

IF: 6.044

2004-01-01

Materials Science and Engineering A

Abstract:Effects of whisker-oriented alignment on sintering behavior of SiC(w)/Si3N4 composites were investigated by sintering curves of SiC(w)/Si3N4 compacts with different whisker alignment (random and unidirectionally oriented). It was found that whisker-oriented alignment led to considerable anisotropy of linear shrinkage and sintering rate of SiC(w)/Si3N4 compacts during sintering. Whisker-oriented alignment could improve the sinterability of the SiC(w)/Si3N4 composites and consequently improve the maximum fraction of whisker addition and reduce the content of sintering additives without obviously lowering the density, which are more beneficial to exert the best reinforcing effects of whiskers and mechanical properties of SiC(w)/Si3N4 composites at elevated temperature.
The Effects of β-Si3N4 Whisker Content and Orientation on R-Curve Behaviors of Si3N4 Ceramics

Lin-Hua Zou,Dong Soo Park,Hai Doo Kim,Chang An Wang,Yong Huang

DOI: https://doi.org/10.4028/www.scientific.net/KEM.287.404

2005-01-01

Abstract:The beta-Si3N4 whisker randomly and unidirectionally reinforced Si3N4 composites were fabricated respectively. The high whisker alignment was obtained by extrusion processing. The R-curve behaviors were studied for the Si3N4 ceramics with addition of 3wt%, 5wt% and 10wt% beta-Si3N4 whisker seeds respectively, and the effects of whisker orientation and content on the R-curve behaviors were analyzed and discussed. The ceramics with different whisker content and orientation showed well-defined R-curve behaviors. However, for the whisker random distribution, as its whisker content increased from 3wt% to 10wt%, the corresponding fracture toughness changed at an irregular trend; for the whisker unidirectional reinforcement, the fracture toughness in the direction perpendicular to whisker alignment was considerably improved, and most of indentation impressions tend to be very abnormal. The effects of whisker orientation and contents on the R-curve behaviors of the Si3N4 ceramics were further discussed.
The effects of β-Si3N4 whisker content and orientation on R-curve behaviors of Si3N4 ceramics

Linhua Zou,Dongsoo Park,HaiDoo Kim,ChangAn Wang,Yong Huang

DOI: https://doi.org/10.4028/0-87849-965-2.404

2005-01-01

Key Engineering Materials

Abstract:The β-Si3N4 whisker randomly and unidirectionally reinforced Si3N4 composites were fabricated respectively. The high whisker alignment was obtained by extrusion processing. The R-curve behaviors were studied for the Si3N 4 ceramics with addition of 3wt%, 5wt% and 10wt% β-Si 3N4 whisker seeds respectively, and the effects of whisker orientation and content on the R-curve behaviors were analyzed and discussed. The ceramics with different whisker content and orientation showed well-defined R-curve behaviors. However, for the whisker random distribution, as its whisker content increased from 3wt% to 10wt%, the corresponding fracture toughness changed at an irregular trend; for the whisker unidirectional reinforcement, the fracture toughness in the direction perpendicular to whisker alignment was considerably improved, and most of indentation impressions tend to be very abnormal. The effects of whisker orientation and contents on the R-curve behaviors of the Si3N4 ceramics were further discussed.
The Effects of β-Si3N4 Whisker Content and Orientation on R-Curve Behaviors of Si3N4 Ceramics

Lin-Hua Zou,Dong Soo Park,Hai Doo Kim,Chang An Wang,Yong Huang

DOI: https://doi.org/10.4028/www.scientific.net/kem.287.404

2005-01-01

Key Engineering Materials

Abstract:The b–Si3N4 whisker randomly and unidirectionally reinforced Si3N4 composites were fabricated respectively. The high whisker alignment was obtained by extrusion processing. The R-curve behaviors were studied for the Si3N4 ceramics with addition of 3wt%, 5wt% and 10wt% b–Si3N4 whisker seeds respectively, and the effects of whisker orientation and content on the R-curve behaviors were analyzed and discussed. The ceramics with different whisker content and orientation showed well-defined R-curve behaviors. However, for the whisker random distribution, as its whisker content increased from 3wt% to 10wt%, the corresponding fracture toughness changed at an irregular trend; for the whisker unidirectional reinforcement, the fracture toughness in the direction perpendicular to whisker alignment was considerably improved, and most of indentation impressions tend to be very abnormal. The effects of whisker orientation and contents on the R-curve behaviors of the Si3N4 ceramics were further discussed.
Fabrication and performance of SiC-reinforced Cu: Role of the aspect ratio of the SiC reinforcement phase

Lu Han,Jing Wang,Siyuan Guo,Yuanyuan Chen,Chunsheng Shi,Yuan Huang,Zumin Wang,Yongchang Liu,Naiqin Zhao

DOI: https://doi.org/10.1016/j.matdes.2022.110869

2022-06-27

Abstract:In this study, SiC particle (SICP)- and SiC whisker (SICW)-reinforced Cu composites were prepared by pulse intermittent deposition and subsequent spark plasma sintering (SPS). After electrodeposition, the formation of Cu-coated SICP and SICW core–shell structures solved the problem of agglomeration of the second phase during the subsequent sintering. In addition, the wetting layer of Cu increased the bonding strength of the interface between Cu and the second phase. The strength of SICP-reinforced Cu was higher than that of pure Cu at the expense of elongation and thermal conductivity. Compared to SICP-reinforced Cu, SICW-reinforced Cu exhibits significantly higher strength, plasticity and thermal conductivity. The externally applied load was transferred from a soft Cu matrix to stiff SICWs, thus increasing the yield strength of the composites. Furthermore, bridge cracks, crack deflection, and whisker pull-out mechanisms improved the elongation of the composite. This work reveals the relevance of the strengthening mechanism and the aspect ratio of the reinforced phase systematically and provides an advanced pathway to fabricate high-performance metal–matrix composites by designing discontinuous second phases with tailored aspect ratios.

materials science, multidisciplinary
Microstructure control of SiCw/SiC composites based on SLS technology

Decai Lu,Liwei Zhang,Su Cheng,Dequan Shi,Kun Zhang,Wencheng Shao,Duomu Lin,Tao Zeng

DOI: https://doi.org/10.1016/j.jeurceramsoc.2022.03.053

IF: 5.7

2022-08-01

Journal of the European Ceramic Society

Abstract:The preparation of SiCw/SiC materials was realized by SLS technology. The effect of SiC powder size on the number and size of SiC whisker formation was investigated. The tortuosity and diameter of open pores are introduced to modify the classical molecular collision model, and the relationship model between the growth rate of SiC whisker and porosity was established. The influence mechanism of powder size on the number of whisker growth was revealed. According to the model, the number of in-situ whisker growth in powder can be calculated, and the calculated results by using this model agreed with the test results. So it is suitable for in-situ whisker microstructure control under SLS technology, and also suitable for other 3D printed whisker in-situ reinforced ceramic material systems. This is of great significance to expand the application of 3D printing ceramic matrix composites.

materials science, ceramics
A comparative study for the thermal conductivities of C/SiC composites with different preform architectures fabricating by flexible oriented woven process

Zheng Sun,Zhongde Shan,Tianmin Shao

DOI: https://doi.org/10.1016/j.ijheatmasstransfer.2021.120973

IF: 5.2

2021-05-01

International Journal of Heat and Mass Transfer

Abstract:Thermal conductivity behaviors are one of the most important evaluations of C/SiC composites in the field of thermal protective structures. Represent volume element (RVE) models of microscale, void/matrix, and mesoscale proposed in this work are used to investigate the thermal conductivity behaviors of the C/SiC composites with different preform architectures. The thermal conductivities of 2.5D woven composites (2.5D), 3D woven orthogonal composites (3D), 3D five-directional woven composites (3DFD) and the combination of three structures fabricating by the flexible oriented woven process (FOWP) are comparatively discussed. The periodic temperature boundary conditions are applied to the RVE models to predict the thermal conductivities (TCs). The proposed analytical methods are validated by the values from the experiment and the literature. In addition, the effect of porosity and structure combination sequences on TCs is also taken into consideration. The results show that the 3D woven orthogonal composites have the lowest TCs and the structure combination sequences have little effect on TCs of C/SiC composites. The present work can potentially help to improve the design process and provide a significant reference to select the appropriate preform architectures.

engineering, mechanical,thermodynamics,mechanics
R-curve behavior of Si3N4 whisker-reinforced Si3N4 matrix composites

Lin-Hua Zou,Yong Huang,Dong-Soo Park,Byung-Uk Cho,Hai-Doo Kim,Byung-Dong Han

DOI: https://doi.org/10.1016/j.ceramint.2004.04.013

IF: 5.532

2005-01-01

Ceramics International

Abstract:Three kinds of β-Si3N4 whisker-reinforced Si3N4 composites with different degree of whisker alignment were prepared by using tape casting, extrusion and hot pressing processes. Among these composites, one is obtained from a laminate with tapes, another is from a laminate stacked alternatively with tapes and extruded wires, and the last one is closely stacked with wires. The same whisker orientation was followed with all the tapes or wires. Four-point bending tests by stepped loading were employed to determine R-curves for the three materials. The results show that all the materials have better R-curve behaviors than composites with randomly oriented whiskers. The fracture toughness of the three materials are, respectively, 11.18, 11.44 and 10.60MPam1/2, and the corresponding threshold values for stable crack propagation are 9.14, 10.92 and 9.32MPam1/2, respectively.
Thermal conductivity and bending strength of SiC composites reinforced by pitch-based carbon fibers

Liyang Cao,Yongsheng Liu,Yunhai Zhang,Yejie Cao,Jingxin Li,Jie Chen,Lu Zhang,Zheng Qi

DOI: https://doi.org/10.1007/s40145-021-0527-5

IF: 11.534

2022-01-11

Journal of Advanced Ceramics

Abstract:Abstract In this work, pitch-based carbon fibers were utilized to reinforce silicon carbide (SiC) composites via reaction melting infiltration (RMI) method by controlling the reaction temperature and resin carbon content. Thermal conductivities and bending strengths of composites obtained under different preparation conditions were characterized by various analytical methods. Results showed the formation of SiC whiskers (SiC w ) during RMI process according to vapor—solid (VS) mechanism. SiC w played an important role in toughening the C pf /SiC composites due to crack bridging, crack deflection, and SiC w pull-out. Increase in reaction temperature during RMI process led to an initial increase in thermal conductivity along in-plane and thickness directions of composites, followed by a decline. At reaction temperature of 1600 °C, thermal conductivities along the in-plane and thickness directions were estimated to be 203.00 and 39.59 W/(m·K), respectively. Under these conditions, bending strength was recorded as 186.15±3.95 MPa. Increase in resin carbon content before RMI process led to the generation of more SiC matrix. Thermal conductivities along in-plane and thickness directions remained stable with desirable values of 175.79 and 38.86 W/(m·K), respectively. By comparison, optimal bending strength improved to 244.62±3.07 MPa. In sum, these findings look promising for future application of pitch-based carbon fibers for reinforcement of SiC ceramic composites.

materials science, ceramics
Preparation and mechanical properties of SiC whisker-reinforced alumina

Xiaofeng Peng,Xiaoxian Huang,Yufeng Zhang

IF: 1.292

1998-01-01

Journal of Inorganic Materials

Abstract:Sic whisker reinforced alumina composites were fabricated by hot-pressing from the commercial gamma-Al2O3 and SiC whisker made in Shanghai Institute of Ceramics. We obtained some samples with 30vol% SiCw hot-pressed at 1800 degrees C in Ar atmosphere having the flexure strength of 812+/-38MPa and fracture toughness of 8.8+/-0.1MPa.m(1/2) at room temperature; 560+/-61MPa and 6.1+/-0.4MPa at 1200 degrees C respectively. The small amount of additions accelerated densification but reduced the mechanical properties. In Nz atmosphere, SiC whisker would be injured and the composites mechanical properties degraded. Moreover, the microstructural observations indicated that the toughening mechanism of AS composites is different from whiskers pull-out and matrix's cleavage fracture at room temperature to whiskers/matrix interface debonding and matrix's intergranual fracture at high temperature.

Resistivity controlled by SiC whisker orientation in Si3N4 matrix composites

Roles of orientation relationship and recrystallization in superplasticity of SiCw/6061Al composite

Processing and Properties of Oriented SiC Whisker-Reinforced Si3N4 Ceramic Matrix Composites

The effect of whisker orientation in SiC whisker-reinforced Si3N4 ceramic matrix composites

Mechanical Behavior of SiCf/SiC Composites with Alternating PyC/SiC Multilayer Interphases

Complex Impedance Analysis on the Orientation Effect of Whiskers in Oriented Silicon Carbide Whisker/Silicon Nitride Composites

The properties of the multi-node SiCw and its reinforced Si 3N4 ceramic composite material

The Dual Effect Of Whiskers On Toughening And Conducting Properties In Aligned Sic Whisker-Reinforced Si3n4-Matrix Composites

The properties of the multi-node SiCw and its reinforced Si3N4 ceramic composite material

Improved Resistance to Damage of Silicon Carbide-Whisker-Reinforced Silicon Nitride-Matrix Composites by Whisker-Oriented Alignment

Influence of Reinforcement with Multimodal Distribution on Thermophysical Properties and Fracture Behavior in Al-Si/SiC Composites Infiltrated under Super-Gravity Field

Improved Sinterability of SiC(w)/Si3N4 Composites by Whisker-Oriented Alignment

The Effects of β-Si<sub>3</sub>N<sub>4</sub> Whisker Content and Orientation on R-Curve Behaviors of Si<sub>3</sub>N<sub>4</sub> Ceramics

The effects of β-Si3N4 whisker content and orientation on R-curve behaviors of Si3N4 ceramics

The Effects of β-Si<sub>3</sub>N<sub>4</sub> Whisker Content and Orientation on R-Curve Behaviors of Si<sub>3</sub>N<sub>4</sub> Ceramics

Fabrication and performance of SiC-reinforced Cu: Role of the aspect ratio of the SiC reinforcement phase

Microstructure control of SiCw/SiC composites based on SLS technology

A comparative study for the thermal conductivities of C/SiC composites with different preform architectures fabricating by flexible oriented woven process

R-curve behavior of Si3N4 whisker-reinforced Si3N4 matrix composites

Thermal conductivity and bending strength of SiC composites reinforced by pitch-based carbon fibers

Preparation and mechanical properties of SiC whisker-reinforced alumina

Resistivity controlled by SiC whisker orientation in Si3N4 matrix composites

Roles of orientation relationship and recrystallization in superplasticity of SiCw/6061Al composite

Processing and Properties of Oriented SiC Whisker-Reinforced Si3N4 Ceramic Matrix Composites

The effect of whisker orientation in SiC whisker-reinforced Si3N4 ceramic matrix composites

Mechanical Behavior of SiCf/SiC Composites with Alternating PyC/SiC Multilayer Interphases

Complex Impedance Analysis on the Orientation Effect of Whiskers in Oriented Silicon Carbide Whisker/Silicon Nitride Composites

The properties of the multi-node SiCw and its reinforced Si 3N4 ceramic composite material

The Dual Effect Of Whiskers On Toughening And Conducting Properties In Aligned Sic Whisker-Reinforced Si3n4-Matrix Composites

The properties of the multi-node SiCw and its reinforced Si3N4 ceramic composite material

Improved Resistance to Damage of Silicon Carbide-Whisker-Reinforced Silicon Nitride-Matrix Composites by Whisker-Oriented Alignment

Influence of Reinforcement with Multimodal Distribution on Thermophysical Properties and Fracture Behavior in Al-Si/SiC Composites Infiltrated under Super-Gravity Field

Improved Sinterability of SiC(w)/Si3N4 Composites by Whisker-Oriented Alignment

The Effects of β-Si<sub>3</sub>N<sub>4</sub> Whisker Content and Orientation on R-Curve Behaviors of Si<sub>3</sub>N<sub>4</sub> Ceramics

The effects of β-Si3N4 whisker content and orientation on R-curve behaviors of Si3N4 ceramics

The Effects of β-Si&lt;sub&gt;3&lt;/sub&gt;N&lt;sub&gt;4&lt;/sub&gt; Whisker Content and Orientation on R-Curve Behaviors of Si&lt;sub&gt;3&lt;/sub&gt;N&lt;sub&gt;4&lt;/sub&gt; Ceramics

Fabrication and performance of SiC-reinforced Cu: Role of the aspect ratio of the SiC reinforcement phase

Microstructure control of SiCw/SiC composites based on SLS technology

A comparative study for the thermal conductivities of C/SiC composites with different preform architectures fabricating by flexible oriented woven process

R-curve behavior of Si3N4 whisker-reinforced Si3N4 matrix composites

Thermal conductivity and bending strength of SiC composites reinforced by pitch-based carbon fibers

Preparation and mechanical properties of SiC whisker-reinforced alumina

The Effects of β-Si<sub>3</sub>N<sub>4</sub> Whisker Content and Orientation on R-Curve Behaviors of Si<sub>3</sub>N<sub>4</sub> Ceramics