Abstract:The high temperature tensile test of Ti-47.5Al-2.5 V-1.0Cr-0.2Zr alloy was carried out by electronic universal testing machine under the condition of 750–900 °C/10 −5 –10 −3 s −1 . The hot tensile stress-strain curves were analyzed, and the constitutive model under hot tensile conditions was established. The microstructure transformation rule and deformation mechanism during tensile process were determined. The results show that the hot tensile curve is longer in the steady-state flow stage corresponding to lower strain rate and higher tensile temperature, the true stress declines and the elongation at break increases. The constitutive equation was established based on the tensile curve data, and the corresponding thermal activation energy was 310.3 kJ/mol. As the rise of tensile temperature and the decline of strain rate, the proportion about cross-layer fracture in the tensile fracture morphology decreases, the number of dimples increases, more lamellar structures change into recrystallized structures, and the softening effect of the alloy is more obvious. The dislocation deformation mechanism mainly includes the existence of dislocation slip and climb, dislocation intersection and dislocation ring or dislocation network formation. Twinning deformation is also another important mechanism of high temperature tensile deformation of TiAl alloy. Twins are formed in parallel with each other, so that the deformation can be further carried out. The dislocations and twins in the deformed microstructure will provide nucleation conditions for recrystallized grains. The dynamic recrystallization(DRX) grains are preferentially formed around the grain boundary and the vicinity of dislocation and twin is also preferred nucleation site for DRX. The DRX behavior is the main softening mechanism, and DRX size and volume fraction corresponding to lower tensile rate and higher tensile temperature are larger.

Tensile fracture behaviour of single crystal alloy DD100 at slow strain rate and high temperature

High temperature tensile fracture behavior of [221] oriented DD100 single crystal superalloy

Temperature Effects on Deformation Substructures and Mechanisms of a Ni-based Single Crystal Superalloy

Anisotropic Tensile Properties in Ni-Based Single-Crystal Superalloy DD6 near [001] Orientation at 760°C

Orientation and temperature dependence of yielding and deformation behavior of a nickel-base single crystal superalloy

Temperature-dependent Mechanical Properties and Fracture Behavior of Directionally Solidified Ti47Al2Cr2Nb Alloy

Temperature Dependence of Deformation Behavior in a Co–Al–W-base Single Crystal Superalloy

Study on high temperature tensile constitutive behavior and deformation mechanism of Ti-47.5Al-2.5 V-1.0Cr-0.2Zr alloy

The role of defects on tensile deformation and fracture mechanisms of AM AlSi10Mg alloy at room temperature and 250 °C

Temperature Dependence in Tensile Properties and Deformation Behavior of GH4169 Alloy

Deformation mechanisms of Al0.1CoCrFeNi at elevated temperatures

Study on Tensile Fracture Behavior of Mg-11.21Gd-1.74Y-0.38Zr Alloy

The tensile properties of single crystals of high-purity iron at temperatures from 100 to ─253°C

Microstructure evolution of a forged TiAl-Nb alloy during high-temperature tensile testing

Effects of Temperature and Secondary Orientations on the Deformation Behavior of Single-Crystal Superalloys

Elevated Temperature Tensile Behavior and Microstructure Evolution of Liquid Phase Sintered 90w–7ni–3fe Alloy

Molecular dynamics simulation of tensile deformation of nano-single crystal aluminum

Effects of deformation parameters and stress triaxiality on the fracture behaviors and microstructural evolution of an Al-Zn-Mg-Cu alloy

Effect of Temperature on the Tensile Deformation Mechanisms of a Fourth Nickel-Based Single Crystal Superalloys

Dynamic behavior and fracture mode of TiAl intermetallics with different microstructures at elevated temperatures

Anomalous Increase of Fracture Toughness of TiAl-based Alloys at High Temperature