CuBr laser applied in a remote laser gated projection system

Zhicong Meng,Guiyan Zhang,Jianhua Jiang,Xiudong Song,Fucheng Lin

1997-01-01

Abstract:Basing on the small CuBr vapor lasers, a remote laser gated projection system was developed. Gated projection imaging of a remote object has been achieved. The brightness and clearness of the image are satisfactory. The typical characteristics of this system were presented.

What problem does this paper attempt to address?

Study on sealed-off CuBr laser

Zhixin Yao,Bailiang Pan,Xing Chen,Tao Ma

1998-01-01

Abstract:The cyclical-regeneration process of CuBr in a sealed-off laser was analyzed. By adopting controlling the temperature of the tube wall and placing copper powder at the electrodes, the operation life of the sealed-off CuBr laser was prolonged efficiently, attaining 358 h in experiment.
Adsorption of Bromine in CuBr Laser

YJ WANG,SY SHI,YJ QIAN,BL PAN,XD DING,QN GUO,LD CHEN,RX FAN

DOI: https://doi.org/10.1117/12.43636

1991-01-01

Abstract:Because the dissociated bromine in CuBr lasers has serious effects on the lifetime of CuBr lasers and the stability of the discharged plasma, it is important in long-lived sealed-off CuBr lasers. The adsorption of bromine on the surface of the copper around the electrodes was measured by a transmission electron microscope and an x-ray energy dispersive spectrometer. It was found that the bromine dissociated from the CuBr molecule by collision in the laser discharge plasma is a negative bromine ion; no positive bromine ion existed. On the average, the atomic percentage of the adsorbed bromine is about 20%. The radial distribution of the atomic percentage of bromine around the copper anode is given and has been explained qualitatively.
20-W Sealed-Off Cubr Vapour Laser Excited with Modified Blumlein Circuit

Bangning Mao,Bailiang Pan,Yubo Wang,Li Chen,Limin Wang

2007-01-01

Abstract:A sealed-off CuBr vapour laser with the maximal average output laser power of 20 W was fabricated and investigated. The corresponding efficiency is 1.2% and the specific average output laser power is 123 mW/cm(3) in an active volume of 163 cm(3). The lifetime of the laser is more than 300 hours operating at 12-15 W.
Kinetic process of UV Cu+ laser in Ne-CuBr longitudinal pulsed discharge

Bai-liang Pan,Gang Chen,Bang-Ning Mao,Zhi-Xin Yao

DOI: https://doi.org/10.1364/OE.14.008644

IF: 3.8

2006-01-01

Optics Express

Abstract:The kinetic process of Cu+ UV laser in Ne-CuBr longitudinal pulsed discharge is analyzed and a comprehensive self-consistent physical model is developed. The temporal evolutions of discharge parameters, main particle densities, the electron temperature, and the laser pulse intensity are numerically calculated. The model results illustrate the process of population inversion and the lasing mechanism. The calculations on the influences of the tube radius and Br atoms on the laser output characteristic well explain the experimental results. c (c) 2006 Optical Society of America.
Optical imaging system with laser gated brightness amplifier

Zhicong Meng,Guiyan Zhang,Xiudong Song,Jianhua Jiang,Fucheng Lin

1997-01-01

Abstract:Based on small sealed-off CuBr vapor lasers, an optical imaging system with laser gated brightness amplifier has been established. It is demonstrated that such a system can be employed to image objects hiding behind diffused environment. The experiments show that the brightness and clearness of the image at the exit plane of system are greatly enhanced. Analysis of the principal imaging characteristics was presented.
Spectral Structure of CuBr Laser under Lower Pressures

Chen Li,Mao Bang-Ning,Wang Yu-Bo,Wang Li-Min,Pan Bai-Liang

DOI: https://doi.org/10.7498/aps.56.5808

IF: 0.906

2007-01-01

Acta Physica Sinica

Abstract:Under consideration of the basic factors such as the level hyperfine structure and isotope split etc., the spectral structures of spontaneous emission of copper atom 578/511nm lines are calculated. A sealed operation CuBr laser with periodical refreshment of the buffer gas are designed and constructed. The 578/511nm spectral structures, produced by CuBr laser at lower Ne buffer gas pressure were measured under different working temperatures and exciting voltages. The spectral structure of spontaneous emission of copper atom 578/511nm lines have multi-peaks similar to their laser spectral structure, but the 578nm laser line isstrongly dependent on the working temperature and the exciting voltage. Some possible reasons are suggested to qualitatively explain the experimental results.
Analysis of the Spectral Structure of CuBr Laser Lines

Yubo Wang,Bangning Mao,Li Chen,Limin Wang,Bailiang Pan

DOI: https://doi.org/10.1016/j.optcom.2007.05.035

IF: 2.4

2007-01-01

Optics Communications

Abstract:The spectral structure of spontaneous emission of copper atom at 510.6nm and 578.2nm was calculated considering the hyperfine structure of energy levels and the isotope shift. The spectral structure of the 510.6nm and 578.2nm laser lines was measured in a sealed-off CuBr laser tube with periodic refreshment of the neon buffer gas under different work temperature and excited voltage. The spectral structure of the spontaneous emission of copper atom was found to have similar outline with its laser lines. The spectrum of the 510.6nm laser line maintains similar outline with three peaks at various discharging parameters while the spectrum of the 578.2nm laser line is strongly dependent on the reservoir temperature and the discharge voltage.
Direct Generation of Femtosecond Cylindrical Vector Beams from a 2.8 Μm Er:ZBLAN Fiber Laser

Xinying Li,Guojun Zhu,Chunyang Ma,Chunxiang Zhang,Dianyuan Fan,Jun Liu

DOI: https://doi.org/10.1063/5.0229808

IF: 4

2024-01-01

Applied Physics Letters

Abstract:Cylindrical vector beams (CVBs), which feature a unique spatially non-uniform polarization distribution with an axis symmetry, have been attracting increasing attention due to their various potential applications. However, mainstream CVB lasers demonstrated so far are emitting in the near-infrared wavelength region. The development of mid-infrared (MIR) CVB lasers can greatly broaden their application areas, especially when operating in the mode-locking regime where high peak power ultrafast pulses can be produced. Here, we present the direct generation of MIR femtosecond CVBs from an Er-doped fluoride fiber laser. The mode-locking operation is realized by the nonlinear polarization rotation technique, accompanying with an intra-cavity CVB converter based on two S-waveplates. Both radially and azimuthally polarized beams in the form of mode-locking pulse trains are achieved in the experiment with a typical pulse width of 336 fs and a peak power of 7.3 kW at a repetition of 42.24 MHz. The center wavelength locates at around 2795 nm. This work can provide a solution for the direct generation of femtosecond CVBs in the MIR wavelength region and facilitate its application in fields such as micro-manufacturing and nanoparticle manipulation.
Reproduction of a Computer-Generated Hologram with a White Light Source and Liquid Crystal Device

Xiao-jie Zhang,Xu Liu,Hai-feng Li

DOI: https://doi.org/10.1117/1.2714982

IF: 1.3

2007-01-01

Optical Engineering

Abstract:The reproduction of computer-generated hologram (CGH) with white light source was realized using a liquid crystal panel instead of holographic film. The Burch-coding CGH was achieved by simulating the interference of a digital image and virtual reference light, displayed on liquid crystal displays and illuminated by a white light-emitting diode. The system is compact and the reconstructed images include full parallax. The full-parallax images of the Fresnel hologram computed with our algorithm were compared with the reproduced images by the rainbow hologram. The results implied this method was ready for the development of real-time three-dimensional color digital holography. (C) 2007 Society of Photo-Optical Instrumentation Engineers.
Stable CsPbBr3‐Glass Nanocomposite for Low‐Étendue Wide‐Color‐Gamut Laser‐Driven Projection Display

Shisheng Lin,Hang Lin,Guoxin Chen,Bo Wang,Xiangming Yue,Qiugui Huang,Ju Xu,Yao Cheng,Yuansheng Wang

DOI: https://doi.org/10.1002/lpor.202100044

2021-01-01

Laser & Photonics Review

Abstract:Up‐to‐date laser‐driven projection technology puts an urgent demand for green phosphor with stringent requirements on its performance. Herein, by virtue of a new architecture design based on CsPbBr3‐glass nanocomposite, i.e., CsPbBr3 glass ceramic film sintered on sapphire plate, the application availability of this famous green‐emitting phosphor is demonstrated in laser‐driven projection. The mono‐dispersed perovskite CsPbBr3 nanostructure in amorphous glass matrix and the negligible thermal corrosion during co‐sintering with low‐melting‐glass ensure good luminescent properties. The robust glass host and the carried sapphire substrate with high thermal conductivity contribute to good resistances to thermal shock, moisture, and blue laser irradiation. It is revealed that the thermal accumulation effect is relieved due to the pulsed excitation of rotatory “phosphor wheel,” and so the luminescence saturation threshold gets increased. The constructed prototype lighting source yields a low étendue of ≈0.41 mm2, a wide color gamut of 128.4% NTSC (95.9% Rec. 2020), and a moderate luminous flux of 174 lm. The present work highlights an unprecedented design that makes the seemingly impossible application of CsPbBr3 come true.
Dynamic model for CuBr UV laser

Gang Chen,Bailiang Pan,Zhixin Yao

2006-01-01

Abstract:The dynamic process of Ne-CuBr UV laser in nanosecond pulsed longitudinal discharge is analyzed, and a comprehensive self-consistent physical model is developed. The temporal evolutions of discharge parameters, main particle densities, electron and gas temperatures, and the laser pulse intensity are numerically calculated. The process of population inversion between the upper and the lower laser levels as well as the lasing mechanism are illustrated. The influences of the tube radius and discharge parameters on the laser output characteristic are also explained quantificationally.
Spectral control in the injection-seeded CuBr laser

Jihong Geng,Guiyan Zhang,Xiudong Song,Fucheng Lin

1996-01-01

Abstract:The experimental results of controlling CuBr laser modes by using an injection seeding technique were reported. The single longitudinal mode CuBr laser pulses was amplified and the narrowing-linewidth copper laser radiation with an average power of more than 100 mW was obtained. The injection seeding process in short-pulse high-gain lasers was analyzed and the experimental results in the injection seeded CuBr laser was discussed.
A Hierarchical Structure Perovskite Quantum Dots Film for Laser‐Driven Projection Display

Shengxiang Liao,Zezhong Yang,Jidong Lin,Shaoxiong Wang,Jiwen Zhu,Shuxin Chen,Feng Huang,Yuanhui Zheng,Daqin Chen

DOI: https://doi.org/10.1002/adfm.202210558

IF: 19

2022-10-27

Advanced Functional Materials

Abstract:High‐quality laser‐driven projection display puts forward urgent demand for color‐converting materials. Herein, a hierarchical structure CsPbX3 (X3 = Br3, Br1.5I1.5) quantum dots‐in‐glass film (QiGF), and fabricate a brand‐new white‐lighting source by coupling blue laser with a pattern "QiGF wheel" is designed. The constructed prototype shows more natural and real color restoration for its wide color gamut display feature. Laser‐driven projection display puts forward urgent demand for color converter materials to achieve wide‐color‐gamut and high‐quality image presentation. In this study, a hierarchical structure quantum dots‐in‐glass film (QiGF) is fabricated via co‐sintering stable green/red‐emitting CsPbX3@glass (X3 = Br3, Br1.5I1.5) and commercial low‐melting glass on the sapphire substrate. Benefiting from the well‐retained optical properties of CsPbX3 quantum dots in amorphous glass and high thermal conductivity, QiGF succeeded in inhibiting luminescence saturation after 20 W mm−2 blue laser irradiation. A brand‐new white‐lighting source designed by coupling a blue laser with a pattern "QiGF wheel" produced ultra‐narrow blue/green/red tri‐color emissions and total luminous flux of 146 lm. Accordingly, a QiGF‐converted laser projection system is successfully designed for the first time, showing more natural and real color restoration for its wide color gamut display feature (157% of conventional light‐emitting diode projection and 107% of NTSC standard). The present study highlights the practical application of CsPbX3 quantum dots composite as an efficient laser‐driven color converter in projection display.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
Full spatial coherent radiation in a large-aperture stable resonator CuBr laser by injection locking

Jihong Geng,Yanqing Wu,Guiyan Zhang,Xiudong Song,Fucheng Lin

1994-01-01

Abstract:The technique of injection locking is a simple, highly reliable and efficient way to generate high power laser radiation with high quality beam performances. This paper reports the complete spatial coherent radiation in a large-aperture stable resonator CuBr laser by injection locking.
A Hybrid Solid-State Beam Scanner for FMCW LiDAR Application.

Zhaoyang Zhang,Xufeng Du,Zhiyan Zhou,Qikai Huang,Qiang Zhang,Tingge Dai,Hui Yu,Yuehai Wang,Jianyi Yang

DOI: https://doi.org/10.1364/ofc.2023.m3f.1

2023-01-01

Abstract:We demonstrate a hybrid solid-state beam scanner based on a Si 3 N 4 switching array. Two-dimensional beam steering with a 14.3°×9.9° field of view and FMCW ranging operation at a distance of 7.4 m are achieved.
Surface Vertical Multi-Emission Laser with Distributed Bragg Reflector Feedback from CsPbI3 Quantum Dots

Xueqiong Su,Yong Pan,Dongwen Gao,Jin Wang,Huimin Yu,Ruixiang Chen,Baolu Guan,Xinyu Yang,Yimeng Wang,Li Wang

DOI: https://doi.org/10.3390/nano13101669

IF: 5.3

2023-05-18

Nanomaterials

Abstract:Quantum dots (QDs) laser has become an important way to solve micro-application problems in many fields. However, single wavelength distributed Bragg reflector (DBR) has many limitations in practical applications, such as signal transmission. How to realize multiwavelength DBR lasing output simply is a challenge. To achieve a stable multi-wavelength quantum dots laser in the near-infrared region, the perovskite CsPbI3 QDs laser with DBR structure is developed in this paper. A tetragonal crystal structure with complete bonding information and no defect is explained by X-ray diffractions (XRD) and Raman spectrum. The cross-section morphology of the DBR laser and the surface morphology of QDs is measured by scanning electron microscope (SEM) and transmission electron microscope (TEM), respectively. An elliptical light propagation field and a double wavelength laser radiation are obtained from the finite-difference time-domain (FDTD) simulation. The output of the three wavelength lasers at 770 nm, 823 nm, and 873 nm is measured. The emission time of a DBR laser is about 2 h, and the average fluorescence quantum yield is 60%. The cavity length selection and energy level model are put in place to clearly see the working mechanism. All the results suggest that an effective and stable CsPbI3 quantum dots DBR laser is realized.

materials science, multidisciplinary,physics, applied,nanoscience & nanotechnology,chemistry
Optical Controlled Switch Behaviour of the Zns : Cu and Sral2o4 : Eu Phosphors

SM Wang,LG Hu,J Zhuo,YW Zeng

DOI: https://doi.org/10.1088/0256-307x/22/10/018

2005-01-01

Abstract:We study the effects of a laser beam from the laser diode operating at 980 nm on the violet-excited ZnS:Cu and SrAl2O4:Eu phosphor powders. Two contrary phenomena, i.e., infrared-induced permanent quenching and short-lived enhancement of phosphorescence, are observed. The defect levels play a significant role in both the processes. It is demonstrated that the phosphorescence induced by the violet beam can be controlled by another infrared beam. The turn-off and turn-on behaviour means that doping luminescent centres into host materials is a considerable way to design a new all-optical switch and may control the output of laser beams in the fibre lasers and optical communications.
A highly stable CsPbBr 3 –SiO 2 glass ceramic film sintered on a sapphire plate for laser-driven projection displays

Jiamin Sun,Zhentong Lu,Yi Liu,Dongwei Zheng,Juqing Li,Lei Jin,Jiayu Zhang,Haoran Zhang,Yingliang Liu,Xuejie Zhang,Bingfu Lei

DOI: https://doi.org/10.1039/d2tc04160j

IF: 6.4

2022-01-01

Journal of Materials Chemistry C

Abstract:A narrow band and stable CsPbBr 3 light converter was elaborately designed for laser-driven projection displays.

materials science, multidisciplinary,physics, applied
Remote Human-computer Interaction Using Laser Pointer

刘芳,林学訚,史元春

DOI: https://doi.org/10.3969/j.issn.1006-8961.2003.11.023

2003-01-01

Journal of Image and Graphics

Abstract:Video projection is in widespread use for multimedia presentations in classrooms and in conferences. Unfortunately, the usual human-computer interaction (HCI) with keyboard and mouse confines the speaker to the computer devices. In this paper, we present a system for remote HCI using a laser pointer. In addition to the projection equipments, the system only requires a video camera and a video capture card. We use the video camera to capture the projection plane, detect the laser point (that is, the region induced by the laser pointer) in the captured frames. We then track and recognize the trajectory of the laser point and translate it into messages sent to the computer system. Compared with the previous work in this area, we develop some novel ideas in the system: first, a training process is introduced to improve the system adaptability; second, multiple cues such as color appearance, motion, and shape, are integrated in laser point detection to improve the system robustness. The experiments demonstrate the usability (robustness) and adaptability of our system.
Improvement of output feature in a large-aperture stable resonator CuBr laser using injection locking

Jihong Geng,Guiyan Zhang,Xiudong Song,Fucheng Lin

1996-01-01

Abstract:The self-mode-locking CuBr laser pulses can be successfully injection-locked and the high-average power mode-locked pulses can be obtained in a stable resonator CuBr laser by using injection locking technique. It is the first time to obtain highly spatial coherent high-power radiation in a stable resonator CuBr laser with a beam diameter of 20 mm and is important for the research on the holographic cinematography with a copper-vapor laser. Moreover, it is also suitable for improving the output feature of another lasers, such as excimer laser.

CuBr laser applied in a remote laser gated projection system

Study on sealed-off CuBr laser

Adsorption of Bromine in CuBr Laser

20-W Sealed-Off Cubr Vapour Laser Excited with Modified Blumlein Circuit

Kinetic process of UV Cu+ laser in Ne-CuBr longitudinal pulsed discharge

Optical imaging system with laser gated brightness amplifier

Spectral Structure of CuBr Laser under Lower Pressures

Analysis of the Spectral Structure of CuBr Laser Lines

Direct Generation of Femtosecond Cylindrical Vector Beams from a 2.8 Μm Er:ZBLAN Fiber Laser

Reproduction of a Computer-Generated Hologram with a White Light Source and Liquid Crystal Device

Stable CsPbBr3‐Glass Nanocomposite for Low‐Étendue Wide‐Color‐Gamut Laser‐Driven Projection Display

Dynamic model for CuBr UV laser

Spectral control in the injection-seeded CuBr laser

A Hierarchical Structure Perovskite Quantum Dots Film for Laser‐Driven Projection Display

Full spatial coherent radiation in a large-aperture stable resonator CuBr laser by injection locking

A Hybrid Solid-State Beam Scanner for FMCW LiDAR Application.

Surface Vertical Multi-Emission Laser with Distributed Bragg Reflector Feedback from CsPbI3 Quantum Dots

Optical Controlled Switch Behaviour of the Zns : Cu and Sral2o4 : Eu Phosphors

A highly stable CsPbBr 3 –SiO 2 glass ceramic film sintered on a sapphire plate for laser-driven projection displays

Remote Human-computer Interaction Using Laser Pointer

Improvement of output feature in a large-aperture stable resonator CuBr laser using injection locking