Abstract:The high-temperature tensile tests were conducted for SP700 Titanium alloy sheet under the temperatures of 755°C, 775°C, 795°C, 815°C, and the strain rates of 1×10 −2 s −1 , 1×10 −3 s −1 , 1×10 −4 s −1 , respectively. The microstructure evolution, Superplasticity deformation characteristics and elongation differences under different forming conditions were investigated. Results indicate that the steady-state flow duration is the longest under the deformation conditions of 775°C and a strain rate of 1×10 −3 s −1 , achieving a maximum elongation of 746 %. At 795°C with the same strain rate, fine porosities can be observed at the α/β phase boundaries in the uniform deformation and fracture zones, with larger porosities at P3 corresponding to more pronounced necking phenomena. At 775°C and a strain rate of 1×10 −3 s −1 , the average grain size of the α phase is maintained at 3–5μm, accounting for 78.6 % of the microstructure. It is suggested that maintaining an average grain size of approximately 4μm after tensile test can result in an even better superplasticity and elongation rate. Furthermore, at a strain rate of 1×10 −3 s −1 , the average grain size of the α phase initially increases and then decreases with the temperature increasing. At 795°C and a strain rate of 1×10 −3 s −1 , the α/β phase boundaries are curved. However, the α/β phase boundaries remain straight after tensile test, under 815°C and a strain rate of 1×10 −3 s −1 . Moreover, the observed dislocation is mainly in the α phase and only a few in the β phase. It shows that the superplastic deformation of SP700 alloy mainly occurs within the α phase, and the dislocation activity of the β phase may be limited.

SUPERPLASTICITY IN LARGE-GRAINED Fe-36.5Al BASED ALLOYS ADDED Ti

A Study of the Superplastic Deformation Behavior of Low-Cost Ti-2Fe-0.1B Alloys

Superplastic Deformation and Microstructure Evolution of Ti-55 Alloy Sheet

The Mechanical Properties of Intermetallic Ni50−xTi50Alx Alloys (X=6,7,8,9)

Effect of Ti on Microstructure and Mechanical Properties of Die-Cast Al-Mg-Zn-Si Alloy

Superplastic Deformation Behavior of As-Received and Hydrogenated Ti2AlNb Alloy

Mechanical properties of rapidly solidified Al-Ti alloys after thermal exposure

Superplastic Behavior of a Metastable Β-Type Ti Alloy Governed by Grain Size: Microstructure Evolution and Underlying Deformation Mechanism

Strength properties and enhanced plasticity of intermetallic TiAl(CrSi) alloys

Investigation on the microstructure evolution and dynamic recrystallization mechanisms of TiAl alloy at elevated temperature

Effect of Ti content on microstructures and mechanical properties of cast Al-2Li-2Cu-0.5Mg alloy

In-situ surface study on the mechanism of high-strain-rate superplasticity in an Al–Cu–Li alloy

Alloys-by-design: Application to titanium alloys for optimal superplasticity

Effect of Ti addition on the mechanical properties and microstructure of novel Al-rich low-density multi-principal-element alloys

Concentration-Dependent High-Temperature Deformation Mechanism of Hexagonal Close-Packed Ti-Al Alloys

Extraordinary superplasticity at low homologous temperature and high strain rate enabled by a multiphase nanocrystalline network

Superplastic Deformation Behavior and Cavity Formation of Ti55 Titanium Alloy

Superplastic Deformation Behaviors and Power Dissipation Rate for Fine-Grained Ti-6Al-4V Titanium Alloy Processed by Direct Rolling

Evading the strength-ductility trade-off at room temperature and achieving ultrahigh plasticity at 800°C in a TiAl alloy

Understanding the influence of forming condition on superplasticity elongation for SP700 Ti-alloy

Tensile properties and fracture toughness of TiAl alloys with controlled microstructures