Selection Of Optimal Working Wavelengths And Bandwidths For Dual-Wavelength Optical Fiber Pyrometer

Y Wang,My Yao,Yb Liao

DOI: https://doi.org/10.1117/12.229240

1996-01-01

Abstract:In this paper, optimal parameter selection method is proposed to determine two working wavelengths, and selection of their bandwidths is also studied in detail. It's of great significance in practical applications.

What problem does this paper attempt to address?

Optimization analysis based on wavelength bandwidth for multi-band pyrometry]

Tai-ran Fu,Xiao-fang Cheng,Xue-liang Fan,Jin-lei Ding

DOI: https://doi.org/10.3321/j.issn:1000-0593.2005.10.004

2005-01-01

Spectroscopy and spectral analysis

Abstract:The present paper establishes the optimization criteria for achieving the optimum measurements in three-band pyrometry under the assumption of linear emissivity model and the sensor design with Gaussian distribution. By varying the FWHM of Gaussian distribution, the optimization analysis is investigated with the choice of the wavelength bandwidth in three-band pyrometry. For specific cases, the simulation results present the optimum bandwidth distribution. Therefore, the discussions in this paper will provide significant theoretical instructions for the design of radiation pyrometer.
Relationship Between Temperature Range and Wavelength Bandwidth for Multi Band Pyrometry

Fu Tai-ran,Cheng Xiao-fang,Zhong Mao-hua,Yang Zang-jian

DOI: https://doi.org/10.3964/j.issn.1000-0593(2008)09-1994-04

2008-01-01

Spectroscopy and spectral analysis

Abstract:In the present paper, based on the linearity spectral emissivity model with two parameters in the narrow investigated waveband, we extend tri-wavelength pyrometry to tri-band pyrometry through waveband measurements of radiation temperature. In tri-band pyrometry, in order to realize the non-distortion measurement, considering the effect of the dynamic range and the minimum sensibility of the sensor on the coupling relation of multi-channel signals, the restriction condition of the effective temperature measurement range is discussed. However, under the assumption of the fixed sensor parameters, the measurement bandwidth of the sensor is an important influencing factor to the effective temperature measurement range in applications of tri-band pyrometry. Then for the measured objects with the known radiation characteristics, the variation of the effective temperature measurement range with the bandwidth of the sensor is presented through numerical simulations. So the required condition of bandwidth of the sensor is theoretically determined through the above discussions of the effective temperature measurement range. The analyses in this paper may provide the necessary theoretical guides to the design of the sensor of radiation temperature measurement.
Optimization analysis of multi-band pyrometry

Tairan Fu,Xiaofang Cheng,Zangjian Yang

2008-01-01

Abstract:This paper investigates how to optimize multi-band pyrometry under the fixed sensor characteristics. The theoretical optimization criteria are established for multi-band pyrometry in order to obtain the maximum and uniform temperature discrimination resolution. The traditional wavelengths optimization choice for multi-wavelength pyrometry is converted to the optimization analysis of the wave-band functions for multi-band pyrometry. Under the assumption of the two-parameter emissivity model and the specified wave-band functions with Gaussian distribution, the optimization examples for tri-band pyrometry are presented through numerical simulations. And a series of conclusions about the optimum distributions of wave-band functions are obtained. The optimization analysis is helpful to the designs and applications of multi-band pyrometer.
The Analysis of Optimization Criteria for Multi-Band Pyrometry

TR Fu,XF Cheng,XL Fan,JL Ding

DOI: https://doi.org/10.1088/0026-1394/41/4/012

2004-01-01

Metrologia

Abstract:This paper presents a new radiation pyrometry, multi-band pyrometry, obtained by increasing the narrow wavelength bandwidth of multi-wavelength pyrometry. The purpose of this paper is to evaluate the necessity for and the merit of multi-band pyrometry, compared with the traditional multi-wavelength pyrometry. Here, we propose theoretical optimization criteria, based on the temperature discrimination resolution, to analyse the characteristics of multi-band pyrometry. The simulation results indicate that the wavelength bandwidth of multi-band pyrometry does affect the temperature discrimination resolution, and the choice of the bandwidth range will have a significant influence on the performance of the radiation pyrometer. Finally, we conclude that the traditional multi-wavelength pyrometry with 'pure' wavelengths is sometimes not the optimum method for measurements of true surface temperatures. However, multi-band pyrometry with the appropriate bandwidth range may be the optimum method to achieve optimum measurements.
Study on Effective Wavelength Calibration Method of Multispectral Pyrometer

Liang Mei,Sun Bo-jun,Sun Xiao-gang,Xie Jun-yan,Yu Chen-tao

DOI: https://doi.org/10.3964/j.issn.1000-0593(2017)08-2352-04

2017-01-01

Spectroscopy and spectral analysis

Abstract:For the problem that the effective wavelength cannot be obtained because the signal is too weak due to fiber coupling during wavelength calibration of optical fiber multi-spectral pyrometer, a new effective wavelength determination method is proposed based on the data of temperature calibration. Based on the Planck's law, a new method for solving the wavelength is presented, combining with the calibration value ratios of different calibration temperature points. Compared with the traditional method of effective wavelength calibration, the new method proposed in this paper not only provides a new way to get the effective wavelength fast, but also avoids the complexity of the wavelength calibration process. Simulation and experiment were used in this paper to verify the feasibility and effectiveness of the new method. The simulation results showed that the new method which was feasible to get the effective wavelength had the anti-random error ability, and the relative error between the true temperature calculation value based on the effective wavelength and the actual value was less than 0.7%. The experimental results showed that the new method could get the effective wavelength of each channel, and further verify the effectiveness of the proposed method. The new method proposed in this paper can also be applied to other multi-spectral pyrometer, providing a theoretical basis for the development and application of the multi-spectral pyrometer.
Fast Fiber-Optic Multi-Wavelength Pyrometer

Tairan Fu,Peng Tan,Chuanhe Pang,Huan Zhao,Yi Shen

DOI: https://doi.org/10.1063/1.3596567

2011-01-01

Abstract:A fast fiber-optic multi-wavelength pyrometer was developed for the ultraviolet-visible-near infrared spectra from 200 nm to 1700 nm using a CCD detector and an InGaAs detector. The pyrometer system conveniently and quickly provides the sufficient choices of multiple measurement wavelengths using optical diffraction, which avoids the use of narrow-band filters. Flexible optical fibers are used to transmit the radiation so the pyrometer can be used for temperature measurements in harsh environments. The setup and calibrations (wavelength calibration, nonlinearity calibration, and radiation response calibration) of this pyrometer system were described. Development of the multi-wavelength pyrometer involved optimization of the bandwidth and temperature discrimination of the multiple spectra data. The analysis results showed that the wavelength intervals, ΔλCCD = 30 nm and ΔλInGaAs = 50 nm, are the suitable choices as a tradeoff between the simple emissivity model assumption and the multiple signal discrimination. The temperature discrimination was also quantificationally evaluated for various wavelengths and temperatures. The measurement performance of the fiber-optic multi-wavelength pyrometer was partially verified through measurements with a high-temperature blackbody and actual hot metals. This multi-wavelength pyrometer can be used for remote high-temperature measurements.
Some Considerations of Pyrometry Optimization Based on Measurement Uncertainties

FU Tai-ran,ZHAO Huan,ZENG Jun,YANG Da-hai,WANG Lu-ping,CHENG Xiao-fang

DOI: https://doi.org/10.3969/j.issn.1671-8097.2010.03.014

2010-01-01

Journal of Thermal Science and Technology

Abstract:Three-color pyrometry with the non-calibration mode was used as an extension of two-color pyrometry.Based on the inherent measurement uncertainties,the analyses of pyrometry optimization were carried out.The optimization purpose was to investigate the effects of inverse algorithms and wavelengths combinations on temperature measurements.Through numerical simulations based on the measurement uncertainties,different iterative algorithms for three-color method and traditional two-color method were compared to determine the optimum iterative algorithm.The choice of wavelengths combination is another important optimization issue.Due to the coupling characteristics of data processing of three wavelength channels,the effects of spectrum wavelengths to measurements greatly differed from the disposals of single-color method and two-color method.Through numerical analyses,the optimization combinations of three wavelengths under the specified measurement conditions were also obtained.The above discussions are necessary for the actual measurement applications of pyrometry.
A dual-parameter Na-based PCF sensor with wide sensing bandwidth based SPR effect

Linchuan Hu,Jianshe Li,zhiyong yin,Zhigang Gao,Hongwei Li,KaiFeng Li,Zhibing Zhang,Shuguang Li

DOI: https://doi.org/10.1088/1402-4896/ad7063

2024-08-18

Physica Scripta

Abstract:Wide sensing bandwidth is a prerequisite for dual-channel sensors to have wide detection range and high sensitivity. In order to obtain a dual-channel optical fiber sensor with wide sensing bandwidth, a Na-based photonic crystal fiber sensor based on surface plasmon resonance effect is proposed.The sensor constructed a fiber core in the central part of the fiber and formed a sensing surface after constructing the double D type polishing surface. The upper sensing surface was successively coated with Na film and polymethyl methacrylate to construct a refractive index (RI) sensing channel, and the lower sensing surface was successively coated with Na film and polydimethylsiloxane to construct a temperature sensing channel. In this paper, the performance of the sensor is numerically analyzed by finite element method. The bandwidth of the sensor covers 600-1700 nm. The results show that when the RI range of the measured object is 1.33-1.42, the maximum sensitivity of the RI sensor is 11100 nm/RIU, and when the temperature range of the measured object is -40-20 °C, the maximum sensitivity of the temperature sensor is 6.4 nm/°C. Meanwhile, the loss peak of the sensor has a lower half-height width and greater detection accuracy. It has a good application prospect in the fields of biosensing and environmental monitoring.

physics, multidisciplinary
A Novel Dual-Wavelength Method for Evaluating Temperature Effect in Fiber-Optic SPR Sensors

Ning Su,Wei Luo,Liusan Wang,Zhengyong Zhang,Rujing Wang

DOI: https://doi.org/10.3390/app11199011

2021-01-01

Abstract:The temperature effect is one of the critical factors to induce the resonance wavelength shift in fiber-optic surface plasmon resonance (SPR) sensors, which leads to the inaccuracy measurement of refractive index (RI) in practical applications. In this study, a novel dual-wavelength method is presented for fiber-optic SPR sensors to measure the changes of RI and temperature simultaneously in real time. A typical model of an SPR-based fiber optical sensor is constructed for theoretical analysis of temperature effect. Both the thermo-optic effect in the fiber core and phonon–electron scattering along with electron–electron scattering in the metal layer are studied systematically in the theoretical model. The linear and independent relationship, about the dependence of defined output signals on the RI and temperature, is validated by a theoretical calculation in specific dual wavelengths. A proof-of-concept experiment is conducted to demonstrate the capability of the presented dual-wavelength technique. The experimental results indicate that the presented dual-wavelength method is technically feasible and can be applied for practical application. Since the presented method only depends on the full advantages of the transfer spectrum data, it can be applied directly to the conventional single-channel fiber-optic SPR without any specific design structure of the sensor probe. The proposed method provides a new way to detect the RI under different thermal conditions and could lead to a better design for the fiber-optic SPR sensors.
New Method for the Design of Multi-Wavelength Optical Head

HT Liu,L Pang,YB Yan

DOI: https://doi.org/10.1117/12.424851

2001-01-01

Abstract:while devising multi-wavelength pick-up head. The case of double wavelength has been settled satisfactorily, while morewavelengths have no concerned report at present. The paper provides a new algorithm named AWDC (the algorithm forwavelength dividing and wavelength combining) here based on YG algorithm to simulate the case of three wavelengths of550nm, 650nm, 780nm, getting the diffraction efficiency of 40.8%, 42%, 10.3% in incident direction and 46.9%, 36.2%,
Investigation on temperature characteristics of weak fiber Bragg gratings in a wide range

Xiaojun Fan,Junfeng Jiang,Xuezhi Zhang,Kun Liu,Shuang Wang,Tiegen Liu

DOI: https://doi.org/10.3788/col201917.120603

IF: 2.56

2019-01-01

Chinese Optics Letters

Abstract:Xiaojun Fan, Junfeng Jiang, Xuezhi Zhang, Kun Liu, Shuang Wang, Tiegen Liu<br/>A weak fiber Bragg grating (WFBG) is an ideal quasi-distributed optical fiber sensor. Special attention should be paid to the spectrum and ... [Chin. Opt. Lett. 17, 120603- (2019)]

optics
A Dual-Wavelength Temperature Sensor Based on Fiber Optic Delay

ning yang,qi qiu,jun su

DOI: https://doi.org/10.4028/www.scientific.net/AMM.742.3

2015-01-01

Applied Mechanics and Materials

Abstract:In this paper, we report a dual-wavelength temperature sensor based on fiber optic delay. This temperature sensor don’t need to rely on accurate spectrum measurement, but to realize temperature measurement by detecting the variation of delay, which can efficiently reduce the cost and complexity of sensor system. In this dual-wavelength system, one wavelength of light is used as a reference and the other one is used for temperature sensing, so this design can effectively eliminate the negative influences of unstable external environment. The principle of this temperature sensor is theoretically derived, the schematic of sensor system is analyzed and the feasibility of this method is tested in the temperature range of 0°C-80°C. Results indicate that, this temperature sensor is able to achieve temperature measurement in a simple way with low cost.
Processing Method of Multi-Wavelength Pyrometer Data for Continuous Temperature Measurements

X. G. Sun,G. B. Yuan,J. M. Dai,Z. X. Chu

DOI: https://doi.org/10.1007/s10765-005-6724-6

2006-01-01

Abstract:The processing of multi-wavelength pyrometer data is a problem that needs further improvements. The solutions developed in earlier decades generally assumed one particular mathematical relation for emissivity versus wavelength in the wavelength range of the measurements. Sometimes this assumption worked and produced acceptable results, but in many other cases this approach provided erroneous results. Individual results were strongly dependent on the assumed mathematical relation that often needed some prior knowledge of the emissivity behavior in the wavelength range. A new data processing method for a multi-wavelength pyrometer for continuous temperature measurements is presented. A linear relation between emissivity and true temperature at different wavelengths is assumed. Based on this assumption, the true temperatures and spectral emissivities at the two continuous temperature measurement points can be simultaneously calculated. Some experimental results for the practical data processing of measurements performed on a solid propellant rocket engine show that the difference between the calculated true temperature and the theoretical true temperature indicated by the rocket engine designer is within ±20 K.
Optimal design and fabrication of SMS fiber temperature sensor for liquid

Ren Xi Gao,Qiang Wang,Fang Zhao,Bo Meng,Shi Liang Qu

DOI: https://doi.org/10.1016/j.optcom.2010.04.027

IF: 2.4

2010-01-01

Optics Communications

Abstract:Single-mode/multi-mode/single-mode (SMS) fiber sensors are optimally designed and used as high sensitivity temperature sensors in special temperature range. It is shown that the width of multi-mode fiber is a key factor influencing the performance of as-fabricated temperature sensors, which can be effectively controlled in the fabrication process by monitoring the output power of SMS fiber during wet acid etching process. As-fabricated temperature sensors show promising potential applications for precisely monitoring chemical reaction temperature in chemistry and biomedicine fields.
Method for temperature measurement of taper long-period fiber Bragg grating

Zhang Hao,Xinfeng Yu,Zhu Yu,Yunfeng Bai,Yongqiang Tian,Suihu Dang

DOI: https://doi.org/10.1117/1.oe.60.5.050501

IF: 1.3

2021-05-17

Optical Engineering

Abstract:We report a temperature measurement method based on fixed wavelength transmission intensity of long-period fiber grating. Relative to wavelength or edge filtering, this method has obvious advantages in measurement accuracy and cost. The relationship between the transmission intensity and temperature at a fixed wavelength is simulated based on the theory of long-period fiber grating coupling mode. The results show that the transmission intensity of the fixed wavelength is linearly related to the temperature with the appropriate parameters. In the experiment, the transmission spectrum shows two resonant peaks at 1485 and 1538 nm. Two fixed wavelengths at 1480.4 and 1549.7 nm were selected, and the results show a linear relationship between transmission intensity and temperature. The temperature sensitivity of the transmission intensity at 1480.4 nm is about 0.0544 dB / ° C, which means the value of I1480.4 nm / I0 changes by 1.3% for every 1°C. To eliminate the influence of light source and enhance the measurement sensitivity, the ratio of the transmission intensity of two fixed wavelengths was selected to carry out the temperature measurement. The temperature sensitivity of the ratio of I1480.4 nm / I1549.7 nm was 0.0729 dB / ° C, that is, the light intensity ratio changed by 1.7% when the temperature changed by 1°C. A more reasonable design of long-period fiber grating and a more appropriate selection of fixed wavelength should be able to obtain higher temperature sensitivity.

optics
Eight-wavelength pyrometer which can simultaneously measure the true temperature and spectral emissivity

孙晓刚,胡晓光,戴景民,丛大成

DOI: https://doi.org/10.3321/j.issn:1002-1582.2001.04.015

2001-01-01

Guangxue Jishu/Optical Technique

Abstract:Based on a new method for the data processing of the multispectral thermometry, a brand-new multiwavelength pyrometer is developed for simultaneously measuring the true temperature and spectral emissivity. Prism technique is used for splitting the radiation beam in the optical system, which can overcome the disadvantages of the traditional method with optical fibers for beam split and interference filters for effective wavelengths defined. SA68D22 module is used so that wireless data communication can be realized. Based on the new emissivity assumption presented here, the multi-wavelength pyrometer can be used for the true temperature and spectral emissivity measurement of the most engineering materials.
Improvements to the Three-Color Optical CCD-based Pyrometer System

Tairan Fu,Huan Zhao,Jun Zeng,Zhe Wang,Maohua Zhong,Congling Shi

DOI: https://doi.org/10.1364/ao.49.005997

IF: 1.9

2010-01-01

Applied Optics

Abstract:We put forward an improved three-color measurement scheme with a color CCD sensor using the combination of effective wavelengths and blackbody calibrations. The process of effective wavelengths realizes the separation of the emissivity function from the measurement integral equation. This improved method not only effectively avoids errors arising from the traditional process adopting the basic wavelengths, but also simplifies the complex integral calculations. For a blackbody or graybody, the measurement performance of the pyrometer was experimentally investigated from the point of the temperature sensitivity. The results show that narrowing the spectrum bandwidth with different bandpass spectral filters may improve the temperature sensitivities. The spectrum adjustment not only makes the linear emissivity more suitable in the narrower waveband, but also reduces the numerical uncertainty of the effective wavelengths. For nongray objects, the effects of the numerical uncertainty of the effective wavelengths to measurements were quantificationally evaluated at different measurement conditions (different temperatures, emissivities, and spectrums). The results indicate that the reference values of 584, 555, and 511nm or 607, 560, and 506nm of the effective wavelengths are reasonable for the present system with the modified spectral response using Filter 1 or Filter 2. The maximum calculation errors arising from the reference effective wavelengths are less than 1.6%. In this paper, the technical realization steps of the improved method are also described. The measurement experiments of a metal sample in hot environments were carried out to further verify the applicability of this improved CCD-based pyrometer. The results agreed well with the spectrometer-based results.
Study on Optical Fiber Temperature Sensor Using Two-Wavelength Light Sources

刘晔,张贇,王采堂,唐胜安,韦兆碧,王锋

DOI: https://doi.org/10.3321/j.issn:0253-987X.2002.04.002

2002-01-01

Abstract:An optical temperature sensor is presented, which adopts two-wavelength light sources and is for the on-line detection of the temperature in high voltage facilities. This system is based on the spectrum absorption characteristics of semiconductor. Optical fiber and optical passive device are employed to detect and transfer temperature signal. The sensor is immune to electro-magnetic interference, and possesses high insulation level. Improved two-wavelength compensating method was used. The measuring system can eliminate the disturbance effect in the optical path of sensor, thus the problem of instability is solved and measurement precision is greatly enhanced. The experimental results identified the correctness of theoretical investigation.
Optimizing multi-parameter distributed fiber sensors: a hybrid Rayleigh-Brillouin-Raman System approach

Kwang Yong Song

DOI: https://doi.org/10.1038/s41377-024-01392-7

2024-02-05

Light Science & Applications

Abstract:An optimized single-end hybrid Rayleigh, Brillouin, and Raman distributed fiber sensing system has been developed for simultaneous measurement of multiple parameters. This system integrates 3-bit pulse coding for the Raman signal and the Brillouin amplification of the Rayleigh-backscattered signal, discriminating strain, temperature, and vibration using a single sensing fiber.

optics
Wavelength Dispersion Analysis on Fiber-Optic Raman Distributed Temperature Sensor System

Weijie Wang,Jun Chang,Guangping Lv,Zongliang Wang,Zhi Liu,Sha Luo,Shuo Jiang,Xiangzhi Liu,Xiaohui Liu,Yongning Liu

DOI: https://doi.org/10.1007/s13320-013-0102-y

IF: 2.814

2013-01-01

Photonic Sensors

Abstract:The influence of the wavelength dispersion on the temperature accuracy of the Raman distributed temperature sensor system (RDTS) is analyzed in detail, and a simple correction algorithm is proposed to compensate the fiber position error caused by the wavelength dispersion. The principle of the proposed algorithm is described theoretically, and the correction on each point along the entire fiber is realized. Temperature simulation results validate that the temperature distortion is corrected and the temperature accuracy is effectively improved from ±5 °C to ±1 °C.

Selection Of Optimal Working Wavelengths And Bandwidths For Dual-Wavelength Optical Fiber Pyrometer

Optimization analysis based on wavelength bandwidth for multi-band pyrometry]

Relationship Between Temperature Range and Wavelength Bandwidth for Multi Band Pyrometry

Optimization analysis of multi-band pyrometry

The Analysis of Optimization Criteria for Multi-Band Pyrometry

Study on Effective Wavelength Calibration Method of Multispectral Pyrometer

Fast Fiber-Optic Multi-Wavelength Pyrometer

Some Considerations of Pyrometry Optimization Based on Measurement Uncertainties

A dual-parameter Na-based PCF sensor with wide sensing bandwidth based SPR effect

A Novel Dual-Wavelength Method for Evaluating Temperature Effect in Fiber-Optic SPR Sensors

New Method for the Design of Multi-Wavelength Optical Head

Investigation on temperature characteristics of weak fiber Bragg gratings in a wide range

A Dual-Wavelength Temperature Sensor Based on Fiber Optic Delay

Processing Method of Multi-Wavelength Pyrometer Data for Continuous Temperature Measurements

Optimal design and fabrication of SMS fiber temperature sensor for liquid

Method for temperature measurement of taper long-period fiber Bragg grating

Eight-wavelength pyrometer which can simultaneously measure the true temperature and spectral emissivity

Improvements to the Three-Color Optical CCD-based Pyrometer System

Study on Optical Fiber Temperature Sensor Using Two-Wavelength Light Sources

Optimizing multi-parameter distributed fiber sensors: a hybrid Rayleigh-Brillouin-Raman System approach

Wavelength Dispersion Analysis on Fiber-Optic Raman Distributed Temperature Sensor System