Abstract:Background: The Accelerator Driven Subcritical System (ADS) uses a proton beam incident on a target to produce neutrons used in a nuclear reactor to process spent fuel in two ways: to accelerate its decomposition into non-radioactive waste, and to increase the rate at which it is recycled into nuclear fuel. Two cryomodules, each consisting of 7 superconducting spoke cavities, 7 superconducting magnets and 7 beam position monitors, are used to accelerate the proton beams from 3.2 MeV to 10 MeV. The superconducting magnet contains a solenoid for beam focusing and two correctors for orbit correction, it is a key component for ADS injection. Purpose: This study aims at a short superconducting magnet design to meet the required integral field strength and to reduce the leakage field at the nearby superconducting spoke cavities. The design current for the solenoid is 210 A. Methods: The main solenoid and two bucking solenoids plus the iron yoke were used to meet the leakage field requirements which is less than 1 G at a distance of 270 mm from the solenoid center. In order to shorten the magnet length to 170 mm, special design methods were taken for the magnet cryostat by removing two conflicts flanges and replacing them with the direct Al ring seal methods. A kind of conducted the current leads similar as that of Large Hadron Collider (LHC) corrector magnets was applied to the 2.1-K, 3 100-Pa cryogenic system. The small store energy magnet led to the introduction of active quench detected system, which is much more reliable. Two short magnets and two spoke cavities were installed inside a test cryomodule to test the online operation properties of the SC magnet and the SC spoke cavity. Results: A quench performance in the vertical test shows that the operating current of the solenoid magnet can reach above 300 A after natural quenching on three occasions during current ramping (260 A, 268 A and 308 A). Online operating test shows that two magnets can work at 4.2 K and 2.1 K, respectively. The quench protection system worked well when two quenches occurred as the liquid helium level decreased. Conclusion: The online operation for the two magnets confirms the physical and the mechanical design, the reliability of the quench detection technique.

Development of A Superconducting Solenoid for Cads

A Compact Superconducting Solenoid for China-ADS Injector II

Development and Testing of the Short Superconducting Magnets for ADS Injection I

Design and Test of an 8T Focusing Superconducting Solenoid of FRIB Driver Linac

The Optimal Design of a 300~MJ Superconducting Magnet Using HTS Tapes

The Optimal Design Of A 300mj Superconducting Magnet Using Hts Tapes

Design and optimization of a novel solenoid with high magnetic uniformity

Magnetic Field and Strain Measurements of A Superconducting Solenoid Magnet for C-Ads Injector-Ii During Excitation and Quench Test

Winding Design for CFETR Central Solenoid Model Coil

Design, Development and Fabrication for BESIII Superconducting Muon Detector Solenoid

Development of Fundamental Power Coupler for C-ADS Superconducting Elliptical Cavities

Winding R&D for CFETR Central Solenoid Model Coil

Full Period Superconducting Section Physics Design for Injector Ii of China-Ads

Basic Design and Progress of Central Solenoid Model Coil for CFETR

The Superconducting Magnet for ADS Injection-I

Physics Design of the Superconducting Section of the CiADS Linac

Design and testing of focusing magnets for a compact electron linac

Mechanical Design of the Half-length Prototype for a Superconducting FECR Ion Source

The Engineering Design of the 1.5 M Diameter Solenoid for the MICE RFCC Modules

Superconducting Feeder System For Iter Central Solenoid Module Final Test Facility

A design of novel type superconducting magnet for super-high field functional magnetic resonance imaging by using the harmonic analysis method of magnetic vector potentials