Abstract:Polymers reinforced with conducting fibers to achieve electrical conductivity have attracted remarkable attention in several engineering applications, and injection molding provides a cost-effective way for mass production. However, the electrical performance usually varies with the molding conditions. Moreover, high added content of conducting fibers usually results in molding difficulties. In this study, we propose using microcellular (MuCell) injection molding for polypropylene (PP)/carbon fiber (CF, 20, and 30 wt%) composites and hope that the MuCell injection molding process can improve both electrical and mechanical performance as compared with conventional injection molded (CIM) parts under the same CF content. Both molding techniques were also employed with and without gas counter pressure (GCP), and the overall fiber orientation, through-plane electrical conductivity (TPEC), and tensile strength (TS) of the composites were characterized. Based on the various processing technologies, the results can be described in four aspects: (1) Compared with CIM, microcellular foaming significantly influenced the fiber orientation, and the TPECs of the samples with 20 and 30 wt% CF were 18-78 and 5-8 times higher than those of the corresponding samples molded by CIM, respectively; (2) when GCP was employed in the CIM process, the TPEC of the samples with 20 and 30 wt% CF increased by 3 and 2 times, respectively. Similar results were obtained in the case of microcellular injection molding-the TPEC of the 20 and 30 wt% composites increased by 7-74 and 18-32 times, respectively; (3) although microcellular injection molding alone (i.e., without GCP) showed the greatest influence on the randomness of the fiber orientation and the TPEC, the TS of the samples was the lowest due to the uncontrollable foaming cell size and cell size uniformity; (4) in contrast, when GCP was employed in the microcellular foaming process, high TS was obtained, and the TPEC was significantly enhanced. The high foaming quality owing to the GCP implementation improved the randomness of fiber orientation, as well as the electrical and mechanical properties of the composites. Generally speaking, microcellular injection combined with gas counter pressure does provide a promising way to achieve high electrical and mechanical performance for carbon-fiber-added polypropylene composites.

Microcellular injection-compression molding (MICM): A novel technology for effectively improving cellular structure of polystyrene foams

Equipment development and experimental investigation on the cellular structure of microcellular injection molded parts

Primary experimental study on microcellular injection molding using newly-developed equipment ∗

Study on cellular structure and skin layer thickness of microcellular injection molded parts using newly-developed equipment

Microstructure and Properties of Microcellular Poly (phenylene Sulfide) Foams by Mucell Injection Molding

Conventional and Microcellular Injection Molding of a Highly Filled Polycarbonate Composite with Glass Fibers and Carbon Black

Cell Morphology And Mechanical Properties Of Microcellular Mucell (R) Injection Molded Polyetherimide And Polyetherimide/Fillers Composite Foams

Microcellular injection molded outstanding oleophilic and sound-insulating PP/PTFE nanocomposite foam

High-strength, impact-resistant PP/PTFE composite foam with enhanced surface appearance achieved through mold-opening microcellular injection molding

Improving of Cell Structure of Microcellular Foams Based on Polypropylene/High-density Polyethylene Blends

Microcellular injection molding of polyether-ether-ketone

High-Quality Foaming and Weight Reduction in Microcellular-Injection-Molded Polycarbonate Using Supercritical Fluid Carbon Dioxide under Gas Counter Pressure

Tailored Morphologies and Properties of High-Performance Microcellular Poly(phenylene Sulfide)/poly(ether Ether Ketone) (PPS/PEEK) Blends

Microcellular injection molding of foamed engineering plastic parts with high dimensional accuracy

Fabrication of Lightweight Microcellular Polyimide Foams with Three-Dimensional Shape by Co2 Foaming and Compression Molding

A Combined In-Mold Decoration and Microcellular Injection Molding Method for Preparing Foamed Products with Improved Surface Appearance

Research on Microcellular ABS Foam by Compression Molding

Processing Effects on the Through-Plane Electrical Conductivities and Tensile Strengths of Microcellular-Injection-Molded Polypropylene Composites with Carbon Fibers

Crystallinity and mechanical properties of polypropylene products foamed by microcellular injection molding process

Effect of Films on In‐Mold Decoration and Microcellular Foaming Injection Molding Parts: Cell Structure, Surface, Warpage, and Mechanical Properties

Improvement of Cellular Structure and Mechanical Properties for Foam Injection Molding PP/EPDM Blend with Mica