Abstract:In this paper, the effect of Si content on the microstructure and mechanical properties of the Al–1.2Mg– x Si–1.2Cu–0.6Mn cast alloy was investigated. The study aimed to explore the optimal addition of Si element to improve the comprehensive properties of alloys. The microstructure, phase composition and fracture morphology of the alloy were determined through OM, SEM, EBSD and XRD analysis. The Si content in the alloy ranged from 0.48 to 2.4 wt.%. With the increase of Si content, the number of strengthening phases increases, which improves the comprehensive properties of the alloy. When the Si content is 0.8 wt.%, the eutectic Mg 2 Si transforms from rod-shaped to larger block shaped, and the formation of coarse Mg 2 Si phase limits the elongation of the alloy. When the Si content is 2.4 wt.%, fine Al 2 Cu phases are present in this alloy and coexist with Al(Fe,Mn)Si phases, while an increase in the Si content appears as partially accompanied by an incipient crystalline Si phase around the Al(Fe,Mn)Si phase. The alloy exhibits a maximum tensile strength, yield strength and elongation of 198.2 MPa, 101.2 MPa and 4.96%, respectively, with a hardness of 80.94 Hv. It consists of five alloy phases, mainly α-Al, Mg 2 Si, Al(Fe, Mn)Si eutectic phase, Q-AlCuMgSi eutectic phase and the beginning crystalline silicon phase formed due to the increased Si content. The Si content can improve alloy strength, but there is some damage to the toughness of the alloy. Higher silicon alloy content results in the formation of fine Al 2 Cu eutectic. This result makes it possible to achieve a higher level of strength with a reduced loss of ductility in the alloy.

Effects of Si addition on properties of Fe-Cr-W-Ti-Y2O3 alloy fabricated by mechanical alloying

Effects of metalloid Si on the microstructure and mechanical properties of Fe36Ni36Cr10Mo1Al17-XSiX alloys

Effect of Si on Fe-rich intermetallic formation and mechanical properties of heattreated Al-Cu-Mn-Fe alloys

Effect of Si on Microstructure and Mechanical Properties of Multi-Nano-Oxide Dispersion Strengthening Ferritic Alloys

Effect of silicon addition on microstructure and mechanical properties of a high strength Ti-4Al-4Mo-4Sn alloy prepared by powder metallurgy

Effect of Ti on Microstructure and Mechanical Properties of Die-Cast Al-Mg-Zn-Si Alloy

Effects of Si addition on mechanical, electrical and magnetic property of Cu-10Fe alloy

Effect of Si element on improving the oxidation resistance of hybrid (Ti5Si3 + TiC) particles reinforced Ti6Al4V matrix composites

Formation Mechanism and Effect on the Mechanical Properties of TiSi Phase for Ti-5Al-5Mo-5Cr-3Nb-2Zr Alloyed by Silicon

Effect of Si Addition on the Weibull Distribution of Tensile Properties of Fe-bearing Al-Cu Alloys

The Effects of Fe and Si Elements on Structural, Mechanical, and Electronic Properties of an Fe–Si–Ti System by First‐Principles Calculations

Effects of Si addition on properties and microstructure of CuCrZr alloy

Effect of Si and C additions on the reaction mechanism and mechanical properties of FeCrNiCu high entropy alloy

Influence of Si Addition on the Microstructures, Phase Assemblages and Properties in CoCrNi Medium-Entropy Alloy

Effects of Zr,Ti and Sc Additions on the Microstructure and Mechanical Properties of Al-0.4Cu-0.14Si-0.05Mg-0.2Fe Alloys

The influence of Si alloying on the crept microstructure and property of a TiAl alloy prepared by powder metallurgy

The effect of Si addition on the microstructure and tensile properties of casting Al-5.0Cu-0.6Mn-1.2Fe alloys

Effect of Y2O3 Addition on the Microstructure, Wear Resistance, and Corrosion Behavior of W-4.9Ni-2.1Fe Heavy Alloy

Effect of Si on Microstructure and Mechanical Properties of FeCrNi Medium Entropy Alloys

Effects of Si addition on crystallization process and soft magnetic properties of high-Fe and high-Cu-content Fe-Si-B-P-Cu nanocrystalline alloys

The Effect of Si Content on the Microstructure and Mechanical Properties of Al–1.2Mg–xSi–1.2Cu–0.6Mn Cast Alloy