Abstract:The application of Ti6Al 4V in lightweight structures subjected to impact loads necessitates a comprehensive understanding of its dynamic response under high strain rates to ensure the safety and reliability of these components. In this paper, the macroscopic compressive mechanical behavior of Ti 6Al 4V under high strain rates was investigated through the split-Hopkinson pressure bar (SHPB) technique at both room temperature and 200 °C, followed by microstructure analysis of the compressed specimens, carried out employing a combination of optical microscopy (OM) and electron backscatter diffraction (EBSD), and elastic modulus and hardness measurements, performed by a nanoindentation instrument. At room temperature, both the modulus and strain hardening exponent of Ti 6Al4V exhibited an initial increase before the strain rate reached 1000 s -1 , after which they decreased at 3400 s -1 . Meanwhile, the flow stress continued to rise with increasing strain rate. Microscopic observations revealed that twinning played a substantial role in the strain hardening effects. Notably, the basal slip system of the hcp (hexagonal close packed) α phase did not display a more favorable trend, while the c+a type slip systems became more active. Under a strain rate of 5000 s -1 , discontinuous dynamic recrystallization emerged as the dominant mechanism, resulting in an increased frequency of low-angle grain boundaries, as well as a reduction in grain size and dislocation density. These results provide a basis for explaining the mechanical behavior of Ti 6Al 4V under high strain rates and offer insights for the establishment of material models that take into account microstructure deformation mechanisms.

Microstructure and Dynamic Mechanical Properties of Tungsten-Based Alloys in the Form of Extruded Rods Via Microwave Heating

Mechanical Properties and Thermal Shock Performance of W-Y2O3composite Prepared by High-Energy-rate Forging

Microstructure and Mechanical Properties of a Hot-Hydrostatically Extruded 93w–4.9ni–2.1fe Alloy

Mechanical Behavior and Dynamic Failure of High-Strength Ultrafine Grained Tungsten under Uniaxial Compression

Microstructure and mechanical properties of high density tungsten alloy and its influence factors

Tungsten heavy alloy: Nano-crystallinity and alloying induced low temperature sintering, microstructure and mechanical properties

Tem Characterization of the Microstructure of Hot-Hydrostatically Extruded 93W-4.9Ni-2.1fe Alloy

Microstructure and mechanical properties of liquid–phase sintered W@NiFe composite powders

The simultaneous improvement of strength and ductility of the 93W-4.6Ni-2.4Fe prepared by additive manufacturing via optimizing sintering post-treatment

Deformation Stored Energy and Dynamic Recrystallization Behavior of Pure Tungsten Processed by Multiple Directional Forging

Microstructure, mechanical behaviour and fracture of pure tungsten wire after different heat treatments

Influence of Hot Extrusion on Microstructure and Mechanical Properties of Tungsten Based Heavy Alloy

Effect Of Heat Treatment On Microstructure And Mechanical Properties Of Hot-Hydrostatically Extruded 93w-4.9ni-2.1fe Alloy

Microstructure and properties of liquid-phase sintered tungsten heavy alloys by using ultra-fine tungsten powders

Densification, Microstructure And Properties Of 90w-7ni-3fe Fabricated By Selective Laser Melting

Dynamic Mechanical Properties and Fracture Characteristics of Tungsten Fiber Reinforced Cu-Based Composites

Microstructure and Mechanical Properties of Ti-6Al-4V Rods Fabricated by Powder Compact Extrusion of TiH 2 /Al 60 V 40 Powder Blend

Dynamic Compressive Behaviour and Microstructural Evolution of Extrusion-Shear Mg–6Zn–1Cu–1Y–0.6Zr Alloy

Fabrication and Characterization of Tungsten Heavy Alloys with High W Content by Powder Metallurgy

Effect of strain rate on the mechanical properties of a tungsten particle reinforced titanium matrix composite

High strain rate mechanical behavior of Ti-6Al-4V with micro–macro correlation under compressive loading