Abstract:The dense WC-M2 high-speed steel matrix composites (WC-M2 HSS MMCs) with different WC content were prepared by mechanical alloying and vacuum sintering process. Tungsten Carbide (WC) with 0, 2, 5, 8, and 10 (by weight %) were dispersed in the matrix. The effects of WC content on the densification mechanism, phase composition, microstructure, fracture morphology, and mechanical and wear properties of the sintered composites were systematically investigated. The experimental results showed that at a vacuum sintering temperature of 1260 °C, the composite material specimens achieved near-full densification, with predominant phases being Martensitic, M 7 C 3 , M 6 C, M 2 C, MC, WC, α-Fe, and γ-Fe. Reasonable WC addition has improved grain uniformity and reduced micro-defects, which enhanced the overall mechanical properties. With an increase in WC content, the hardness and relative density of the composites showed a gradual increase, whereas transverse rupture strength and impact toughness initially improved but subsequently decreased. The friction coefficient displayed an initial increase followed by a decrease, while the wear rate showed an opposite trend. The impact fracture morphology is dominated by the interfacial separation between the WC particle phase and the binder phase, supplemented by the plastic tearing of the binder phase. The impact toughness mainly depended on the fracture of the binder phase. During crack propagation, both intergranular and transgranular fractures exist, of which the intergranular fracture prevails and coarse grains are more prone to transgranular fracture. With 5 wt.% WC, the steel matrix composites obtained peak mechanical performance, with impact toughness, bending strength, and hardness measuring 13.2 J cm −2 , 1584.3 MPa, and 780.9 HV, respectively, which also yielded the highest wear resistance.

Effect of strain rate on the mechanical properties of a tungsten particle reinforced titanium matrix composite

Mechanical Properties and Thermal Shock Performance of W-Y2O3composite Prepared by High-Energy-rate Forging

High Strain Rate Response of In-Situ TiB2/7055 Composite by Taylor Impact

Advanced tensile properties and strain rate sensitivity of titanium matrix composites reinforced with CaTiO3 particles

The Effect of Y2O3 Particles on the Microstructure and Mechanical Properties of Tungsten Fiber-Reinforced Tungsten Composites

Effect of Microstructure on High-Speed Tensile Mechanical Properties of Ti-1300 Alloy

High strain rate mechanical behavior of Ti-6Al-4V with micro–macro correlation under compressive loading

Effect on microstructure and mechanical properties of in situ 6 wt%TiB2/Al–Zn–Mg–Cu composite subjected by two-step orthogonal deformation process

Effect of Ti particles on microstructure and mechanical properties of TiP/AZ91 composites

The effect of strain rate on deformation-induced α′ phase transformation and mechanical properties of a metastable β-type Ti–30Zr–5Mo alloy

Superplastic deformation behavior of 5 vol% (TiBw+TiCp)/Ti matrix composite sheets with lamellar microstructure

Effect of tungsten micro-scale dispersed particles on the microstructure and mechanical properties of Ti–6Al–4V alloy

Effect of Tungsten Carbide Additions on the Microstructure, Mechanical, and Tribological Properties of M2 High-Speed Steel Matrix Composites

Strain rate dependence of deformation-induced transformation and twinning in a metastable titanium alloy

Mechanical Response and Deformation Mechanisms of TB17 Titanium Alloy at High Strain Rates

The influence of metallic particle size on the mechanical properties of PTFE-Al-W powder composites

Microstructures and tensile properties of low-cost TiBw/Ti–6Al–4V composites by vacuum reactive hot pressing

Mechanical and tribological properties of WC particles reinforced Cu-20Zn matrix composites

Titanium Particulate Reinforced AZ31 Magnesium Matrix Composites with Improved Ductility Prepared Using Friction Stir Processing

High Strain and Strain-Rate Behaviour of PTFE/Aluminium/Tungsten Mixtures

The dynamic mechanical response of Al2O3 and TiB2 particulate reinforced aluminum matrix composites produced by in-situ reaction