Abstract:In this study, the cooperative effect of Mg and Si contents on the microstructural evolution, mechanical properties, and deformation behavior of the cast Al–Li–Mg–Si alloys is investigated. Five different Al–Li–Mg–Si alloys are prepared by conventional casting method, which are referred to as Alloy A-E. The results show that with the increase in the Mg content, the amount of lath-like Mg2Si precipitates and bulk-like AlLiSi particles increases, which leads to an improvement in the strength and ductility of alloys. The amount of intergranular Si-rich phases in Alloy D increases with the increase in the Si content. Further, a higher Si content in Alloy E promotes the formation of bulk-like AlLiSi. The geometric phase analysis (GPA) results reveal strain partitioning behavior at the interface of Mg2Si precipitates and AlLiSi particles, which follows the Orowan looping or dislocation cutting strengthening mechanism. The geometrically necessary dislocation (GND) density calculation results suggest that the lath-like Mg2Si precipitates play a critical role in the deformation behaviors of Alloy A-C. The hindering effect of lath-like Mg2Si precipitates on the movement of dislocations decreases the GND density gap between high-angle grain boundaries or junctions and grain interior and improves the resistance to deformation. However, the deformation behaviors of Alloy D and E with higher Si content are mainly governed by the intergranular Si-rich phases. Finally, a methodological framework is established to elucidate the effect of precipitates and/or intergranular phases on the deformation behaviors of materials using a combination of GPA and GND density calculation methods.

Effect of Si Content on Microstructure and Mechanical Properties of Al–Si–Mg Alloys

Effect of Si Content on Dynamic Recrystallization of Al-Si-Mg Alloys During Hot Extrusion

Effect of hot extrusion on mechanical properties and microstructure of near eutectic Al–12.0%Si–0.2%Mg alloy

The Effect of Si Content on the Microstructure and Mechanical Properties of Al–1.2Mg–xSi–1.2Cu–0.6Mn Cast Alloy

The Effect of Sb Addition on Microstructures and Tensile Properties of Extruded Al–20Mg2Si–4Cu Alloy

Microstructure and mechanical properties of Al−Mg−Si alloy U-shaped profile

Cooperative Effect of Mg and Si Contents on the Microstructural Evolution, Mechanical Performance, and Deformation Behavior of Cast Al–Li–Mg–Si Alloys

Effect of Si content on microstructures and mechanical properties of Al-5.0Cu-0.6Mn-0.7Fe alloy prepared by squeeze casting

Microstructure and Mechanical Behavior of Mg-0.5Si-xSn Alloys

Microstructure Evolution of Al-0.35%Si-0.2%Mg-0.3%Ce Alloy During Hot Extrusion and Its Contributions to Performances

Regulative Effect of Mg/Si Ratio on Microstructure Evolution and Mechanical Properties of Cast Al-Li-Mg-Si Alloys

Effects of Aluminum Content on the As-Cast Microstructure and Mechanical Properties of Mg-xAl-0.7Si Based Alloys

Effect of Si and Mg Level on Microstructure and Properties of Al-Mg-Si-Li Alloys

Dynamic precipitation of Mg2Si induced by temperature and strain during hot extrusion and its impact on microstructure and mechanical properties of near eutectic Al–Si–Mg–V alloy

Influence of Si Contents on Microstructures and Mechanical Properties of High Strength and Toughness 7050 Aluminum Alloys

Revealing the Effect of Si Content on the Microstructure and Properties of Al–Si Alloy by Experiments and Phase-Field Simulation

Microstructure and Mechanical Properties of As-Cast and Extruded Mg-8Li-3Al-0.7Si Alloy

Influence of Varied Mg/Si Mass Ratio on the Microstructure and Mechanical Properties of Aluminum Die Casting Alloys

Optimization of Si Content to Inhibit Inhomogeneous Deformation in Al-Mg-Si Alloy Fabricated via Twin-Roll Casting

Effects of Si content on microstructure and mechanical properties of Mg-Gd-Y-Zr casting alloy

Microstructure and Mechanical Properties of as-Cast Mg-Li-Al-xSi Alloys