Abstract:The effects of varying Mg and Si levels on the microstructural inhomogeneity and eutectic Mg 2 Si morphology in die-cast Al–Mg–Si alloys have been investigated. It was found both Mg and Si additions decreased the microstructural inhomogeneity by producing more well distribution of primary α-Al and Al–Mg 2 Si eutectics, but had contrary effects on eutectic Mg 2 Si morphology. The increasing Mg level transformed eutectic Mg 2 Si from rod or lamellae to curved flake with larger eutectic spacing λ, while the increasing Si level promoted the formation of rod-like or lamellar eutectic Mg 2 Si with smaller λ. The reason for the above evolutions can be traced back to alloys’ solidification behaviour. Thermodynamic calculation indicates that both Mg and Si decrease the liquidus temperature and suppress the precipitation of coarse primary α-Al grains (which tend to agglomerate in centre zone of samples) during the first solidification in shot sleeve, thus reducing the microstructural inhomogeneity. Mg addition shifts the eutectic point to lower Mg 2 Si concentration and induces a slower eutectic growth rate, causing a lower Mg 2 Si volume fraction in Al–Mg 2 Si eutectic cell. On the contrary, Si addition increased the Mg 2 Si volume fraction in eutectic cell by raising the Mg 2 Si eutectic concentration and the eutectic growth rate. To minimize the interfacial energy, Al–Mg 2 Si eutectics with different Mg 2 Si volume fractions exhibit various morphologies. The tensile test results show that both Mg and Si improved the strength at the cost of ductility. However, due to the formation of fine Al–Mg 2 Si eutectics, Si induced less ductility sacrifice than Mg when achieving the same strength improvement.

Influence of Varied Mg/Si Mass Ratio on the Microstructure and Mechanical Properties of Aluminum Die Casting Alloys

Effect of Zn Concentration on the Microstructure and Mechanical Properties of Al-Mg-Si-Zn Alloys Processed by Gravity Die Casting

Regulative Effect of Mg/Si Ratio on Microstructure Evolution and Mechanical Properties of Cast Al-Li-Mg-Si Alloys

The Effects of Varying Mg and Si Levels on the Microstructural Inhomogeneity and Eutectic Mg2Si Morphology in Die-Cast Al–Mg–Si Alloys

Effects of Mg on the Microstructure and Mechanical Property of Al-Si-Mg Casting Alloys

Effect of Mg Level on the Microstructure and Mechanical Properties of Die-Cast Al–Si–Cu Alloys

Melt Superheating on the Microstructure and Mechanical Properties of Diecast Al-Mg-Si-Mn Alloy

The Effect of Si Content on the Microstructure and Mechanical Properties of Al–1.2Mg–xSi–1.2Cu–0.6Mn Cast Alloy

Influence of the Mg Content on the Microstructure and Mechanical Properties of Al-xMg-2.0Si-0.6Mn Alloy

Effect of Mg addition on microstructure and mechanical properties of Al-Si-Cu-Fe alloy with squeeze casting

Effect of Fe, Mn, Ce on the Microstructure and Mechanical Properties of Al-Mg and Al-Mg-Si Die Casting Alloys

Cooperative Effect of Mg and Si Contents on the Microstructural Evolution, Mechanical Performance, and Deformation Behavior of Cast Al–Li–Mg–Si Alloys

Effect of Si and Mg Level on Microstructure and Properties of Al-Mg-Si-Li Alloys

Microstructure, Mechanical Properties and Die-Filling Behavior of High-Performance Die-Cast Al–Mg–Si–Mn Alloy

Investigation of the Influences of Ternary Mg Addition on the Solidification Microstructure and Mechanical Properties of As-Cast Al–10Si Alloys

Effects of Cu Content and Cu/Mg Ratio on the Microstructure and Mechanical Properties of Al–Si–Cu–Mg Alloys

Effect of Iron-Rich Intermetallic and Eutectic Si Accumulation on Al-Si-Mg Alloy

Microstructure and Mechanical Properties of as-Cast Mg-Li-Al-xSi Alloys

Interactions Between Fe-rich Intermetallics and Mg-Si Phase in Al-7Si-xMg Alloys

Effect of Si Content on Microstructure and Mechanical Properties of Al–Si–Mg Alloys

Microstructure and Mechanical Properties of High Strength and Toughness Die Casting Al-Mg-Si-Mn Alloys