Abstract:Single-stage hydrotreating (HDT) of loblolly pine biocrude produced from catalytic pyrolysis was conducted to gain insight to HDT performance in terms of product yields, liquid product quality, and hydrogen consumption. Tests were performed with a sulfided HDT catalyst at three different conditions. The longest continuous time onstream operation (365 h) was achieved at an average bed temperature of 290 degrees C, 138 bar pressure, H2/oil ratio of 3300 Nl l(-1), and a liquid hourly space velocity (LHSV) of 0.25 h(-1). The average carbon yield of the HDT liquids were 77%, 83%, and 89% for experiments 1, 2, and 3, respectively. Also, the biocrude carbon that ended up in the gas phase varied between 4.3% and 8.9%. The carbon in the aqueous phase fraction was negligible-less than 0.5% of the biocrude carbon. The average hydrogen consumed ranged from 0.04 g to 0.07 g per 1 g of dry biocrude. The highest carbon content measured for the HDT liquid products from all three experiments was 87.13 wt% and the lowest was 79.03 wt%. GC-MS analysis suggests that the HDT product with oxygen content less than 5 wt% contained mainly naphthenic hydrocarbons. On the other hand, HDT products with oxygen content greater than 5 wt% contained a higher concentration of simple phenols and aromatic hydrocarbons (mono-and poly-). Catalyst deactivation was evident in the quality of the HDT liquid collected over time; the density and viscosity increased, the H/C ratio and carbon contents decreased; also, the gasoline fraction decreased while the gas oil fraction increased. The results from this work suggest that HDT of biocrude produced by catalytic biomass pyrolysis can be successfully upgraded into hydrocarbon liquid fuels without a stabilization step.

Hydrocracking of Jatropha oil over Ni-H3PW12O40/nano-hydroxyapatite catalyst

Hydrocracking of Bio-Alkanes over Pt/Al-MCM-41 Mesoporous Molecular Sieves for Bio-Jet Fuel Production

Integration of catalytic fast pyrolysis and hydroprocessing: a pathway to refinery intermediates and “drop-in” fuels from biomass

Hydrocracking of Polyolefin Thermal Cracking Waxes Over Ni-loaded Molecular Sieve Catalysts

Direct Selective Hydrogenation of Fatty Acids and Jatropha Oil to Fatty Alcohols over Cobalt-Based Catalysts in Water

Catalytic hydrocracking of jatropha oil over natural clay for bio-jet fuel production

Hydrocracking of Palm Oil to Jet Biofuel over Different Zeolites

Hydroconversion of Jatropha Oil to Alternative Fuel over Hierarchical ZSM-5

Hydrodeoxygenation and Hydrocracking of Microalgae Biodiesel to Produce Jet Biofuel over H3PW12O40-Ni/hierarchical Mesoporous Zeolite Y Catalyst

Efficiency conversion of jatropha oil into high-quality biofuel over the innovative Ni-Mo2N based catalyst

Catalytic conversion of Jatropha oil to alkanes under mild conditions with a Ru/La(OH)3 catalyst

Solid Acid Catalyst WO3-ZrO2 for the Catalytic Deoxygenation of Jatropha Oil for the Preparation of Aviation Paraffin

Jet Fuel Range Hydrocarbons Production Through Competitive Pathways of Hydrocracking and Isomerization over HPW-Ni/MCM-41 Catalyst

Efficient Hydrogenation of Various Renewable Oils over Ru-HAP Catalyst in Water

Efficient production of hydrogen and carbon nanotubes via the cracking of a waste cooking oil model compound over ordered mesoporous Ni/KIT-6 catalysts

Catalytic hydroprocessing of waste cooking oil for the production of drop-in aviation fuel and optimization for improving jet biofuel quality in a fixed bed reactor

Additional Β Zeolites in SiO 2 −al 2 O 3 Supported Pt and Pd Catalysts for Hydrocracking of Paraffin Wax

Hydrotreating of Waste Tire Pyrolysis Oil over Highly Dispersed Ni2P Catalyst Supported on SBA-15

Hierarchical Porous Honeycomb NiCo/C Catalyst for Decarboxylation of Fatty Acids and Upgrading of Sludge Bio-Crude

Hydrodeoxygenation of Palm Oil to Hydrocarbon Fuels over Ni/SAPO-11 Catalysts

The effect of support on nickel phosphide catalysts for one-pot conversion of jatropha oil into high grade hydrocarbons