Abstract:A graded anode-supported solid oxide fuel cell (SOFC) with the structure porous Ni-yttria stabilized zirconia (Ni-YSZ)vertical bar microporous Ni-YSZ vertical bar YSZ vertical bar La0.8Sr0.2MnO3 (LSM) was fabricated by a trilayer co-pressing-sintering method, and coating with an LSM cathode. Cu-CeO2 was impregnated into the porous Ni-YSZ layer using nitrate/glycol precursors to act as an anti-carbon catalyst to fabricate a graded Cu-CeO2-NiO-YSZ composite anode. The current-voltage (I-V), current-power (I-P), and long-term stability of the SOFC were tested using CH4 or H-2 as fuels and air as an oxidant. The results show that the co-pressing-sintering layers possess a gradient pore structure with defect-free combination. The power density of SOFC supported by a graded Ni-YSZ anode is 284 mW.cm(-2), operated at 850 degrees C using H-2 as a fuel, but decreases to 143 mW.cm(-2) when the fuel is changed to CH4. In contrast, the cell supported by a Cu-CeO2-Ni-YSZ anode show the reverse behavior, increasing from 176 to 196 mW.cm(-2) when the fuel is changed from H-2 to CH4 at 850 degrees C. Under a 250 mA.cm(-2) load using CH4 as the fuel, the output of the cell with a graded Ni-YSZ anode fluctuats and the cell is blocked after 10 h. At this point, carbon particles or fibers are observed in the anode layer by scanning electron microscopy (SEM). Conversely, the cell with a Cu-CeO2-Ni-YSZ anode shows stable power output for 50 h or longer, and no carbon deposition was observed inside the anode.

Effect of the co-spun anode functional layer on the performance of the direct-methane microtubular solid oxide fuel cells

Carbon-resistant Ni-YSZ/Cu-CeO2-YSZ dual-layer hollow fiber anode for micro tubular solid oxide fuel cell

Novel light-weight, high-performance anode-supported microtubular solid oxide fuel cells with an active anode functional layer

Fabrication of Y2O3-stabilized-ZrO 2(YSZ)/La0.8Sr0.2MnO3-α-YSZ dual-layer hollow fibers for the cathode-supported micro-tubular solid oxide fuel cells by a co-spinning/co-sintering technique

Microstructure tailoring of YSZ/Ni-YSZ dual-layer hollow fibers for micro-tubular solid oxide fuel cell application

Carbon-Resistant Micro Tubular SOFCs Fabricated by Co-Spinning Process Based on a Phase-Inversion Method

Electrolyte Thickness Control and Its Effect on YSZ/Ni-YSZ Dual-layer Hollow Fibres

Fabrication of Anode Supported Micro Tubular SOFCS by Dip-Coating Process on NiO/YSZ Hollow Fibers

Microstructure Tailoring of the Nickel Oxide-Yttria-Stabilized Zirconia Hollow Fibers Toward High-Performance Microtubular Solid Oxide Fuel Cells

Fabrication and Characterization of High Performance Intermediate Temperature Micro-Tubular Solid Oxide Fuel Cells

Direct-Methane Solid Oxide Fuel Cells with Hierarchically Porous Ni-Based Anode Deposited with Nanocatalyst Layer

Preparation and Properties of Direct-Methane Solid Oxide Fuel Cell Based on a Graded Cu-CeO<sub>2</sub>-Ni-YSZ Composite Anode

Fabrication and Evaluation of NiO/Y2O3-stabilized-ZrO2 Hollow Fibers for Anode-Supported Micro-Tubular Solid Oxide Fuel Cells

Improvement of the Performances of Tubular Solid Oxide Fuel Cells by Optimizing Co-Sintering Temperature of the NiO/YSZ Anode-Ysz Electrolyte Double Layers

Performance of an Anode-Supported SOFC with Anode Functional Layers

A Phase Inversion/Sintering Process to Fabricate Nickel/Yttria-Stabilized Zirconia Hollow Fibers As the Anode Support for Micro-Tubular Solid Oxide Fuel Cells

Co-sintering of gradient anode – electrolyte structure for microtubular SOFC

Sputter-deposited medium-temperature solid oxide fuel cells with multi-layer electrolytes

Reactive Sputtered NiO-YSZ Anode Functional Layer for Thin Film Low-Temperature Solid Oxide Fuel Cell

Slip Casting Combined with Colloidal Spray Coating in Fabrication of Tubular Anode-Supported Solid Oxide Fuel Cells

High Performance Anode-Supported Tubular Solid Oxide Fuel Cells Fabricated by a Novel Slurry-Casting Method