Abstract:The frontal polymerization (FP) of carbon/epoxy (C/Ep) composites is investigated, considering FP as a viable route for the additive manufacturing (AM) of thermoset composites. Neat epoxy (Ep) resin-, short carbon fiber (SCF)-, and continuous carbon fiber (CCF)-reinforced composites are considered in this study. The evolution of the exothermic reaction temperature, polymerization frontal velocity, degree of cure, microstructures, effects of fiber concentration, fracture surface, and thermal and mechanical properties are investigated. The results show that exothermic reaction temperatures range between 110 °C and 153 °C, while the initial excitation temperatures range from 150 °C to 270 °C. It is observed that a higher fiber content increases cure time and decreases average frontal velocity, particularly in low SCF concentrations. This occurs because resin content, which predominantly drives the exothermic reaction, decreases with increased fiber content. The FP velocities of neat Ep resin- and SCF-reinforced composites are seen to be 0.58 and 0.50 mm/s, respectively. The maximum FP velocity (0.64 mm/s) is observed in CCF/Ep composites. The degree of cure (αc) is observed to be in the range of 70% to 85% in FP-processed composites. Such a range of αc is significantly low in comparison to traditional composites processed through a long cure cycle. The glass transition temperature (Tg) of neat epoxy resin is seen to be approximately 154 °C, and it reduces slightly to a lower value (149 °C) for SCF-reinforced composites. The microstructures show significantly high void contents (12%) and large internal cracks. These internal cracks are initiated due to high thermal residual stress developed during curing for non-uniform temperature distribution. The tensile properties of FP-cured samples are seen to be inferior in comparison to autoclave-processed neat epoxy. This occurs mostly due to the presence of large void contents, internal cracks, and a poor degree of cure. Finally, a highly efficient and controlled FP method is desirable to achieve a defect-free microstructure with improved mechanical and thermal properties.

Rapid curing epoxy resin and its application in carbon fibre composite fabricated using VARTM moulding

Rapid curing epoxy resin and the properties of carbon fiber/epoxy composite

Effect of rapid curing process on the properties of carbon fiber/epoxy composite fabricated using vacuum assisted resin infusion molding

Rapid Vacuum Infusion and Curing of Epoxy Composites with A Rubber-Cushioned Mold Design

Preparation of short carbon fiber reinforced photosensitive resin and composite material properties study

Rapid curing vacuum-assisted resin infusion molding using silicone rubber sheet heater and the effect of cooling process on the properties of carbon fiber/epoxy composites

Interface Controlled Micro- and Macro-Mechanical Properties of Vibration Processed Carbon Fiber/Epoxy Composites

Effect of rapid manufacturing on the performance of carbon fibre epoxy polymers

Resin impregnation and interface property improvement of CFRP composite via modulating wettability of carbon fibers

Study on improving the toughness of rapidly curing epoxy resin composite materials with a biobased microcrystalline cellulose

Influence of Epoxy Resin Curing Kinetics on the Mechanical Properties of Carbon Fiber Composites

Effect of microwave irradiation on carbon fiber/epoxy resin composite fabricated by vacuum assisted resin transfer molding

A review of the curing rate and mechanical properties of epoxy resin on polymer matrix composites

Degree of Cure, Microstructures, and Properties of Carbon/Epoxy Composites Processed via Frontal Polymerization

The preparation and characterization of a carbon fiber-reinforced epoxy resin and EPDM composite using the co-curing method

Bamboo fiber‐reinforced epoxy composites fabricated by vacuum‐assisted resin transfer molding (VARTM): Effect of molding sequence and fiber content

Study on the Curing of Vinyl Ester Resin Composites

UV-induced frontal polymerization for optimized in-situ curing of epoxy resin for excellent tensile and flexural properties

Characterization and Finite Element Modeling for Thermoset Resin of Carbon Fiber Prepregs During Curing

INFLUENCE OF CARBON FIBER IN EPOXY RESIN CURING

UV Ageing of Epoxy Resin-Based Glass Fiber-Reinforced Polymer Composites Incorporating with Various Curing Agents