Abstract:The frontal polymerization (FP) of carbon/epoxy (C/Ep) composites is investigated, considering FP as a viable route for the additive manufacturing (AM) of thermoset composites. Neat epoxy (Ep) resin-, short carbon fiber (SCF)-, and continuous carbon fiber (CCF)-reinforced composites are considered in this study. The evolution of the exothermic reaction temperature, polymerization frontal velocity, degree of cure, microstructures, effects of fiber concentration, fracture surface, and thermal and mechanical properties are investigated. The results show that exothermic reaction temperatures range between 110 °C and 153 °C, while the initial excitation temperatures range from 150 °C to 270 °C. It is observed that a higher fiber content increases cure time and decreases average frontal velocity, particularly in low SCF concentrations. This occurs because resin content, which predominantly drives the exothermic reaction, decreases with increased fiber content. The FP velocities of neat Ep resin- and SCF-reinforced composites are seen to be 0.58 and 0.50 mm/s, respectively. The maximum FP velocity (0.64 mm/s) is observed in CCF/Ep composites. The degree of cure (αc) is observed to be in the range of 70% to 85% in FP-processed composites. Such a range of αc is significantly low in comparison to traditional composites processed through a long cure cycle. The glass transition temperature (Tg) of neat epoxy resin is seen to be approximately 154 °C, and it reduces slightly to a lower value (149 °C) for SCF-reinforced composites. The microstructures show significantly high void contents (12%) and large internal cracks. These internal cracks are initiated due to high thermal residual stress developed during curing for non-uniform temperature distribution. The tensile properties of FP-cured samples are seen to be inferior in comparison to autoclave-processed neat epoxy. This occurs mostly due to the presence of large void contents, internal cracks, and a poor degree of cure. Finally, a highly efficient and controlled FP method is desirable to achieve a defect-free microstructure with improved mechanical and thermal properties.

Influence of Epoxy Resin Curing Kinetics on the Mechanical Properties of Carbon Fiber Composites

Influence of the Epoxy Resin Process Parameters on the Mechanical Properties of Produced Bidirectional [±45°] Carbon/Epoxy Woven Composites

Cure Kinetics of an Epoxy Resin Containing Naphthyl/dicyclopentadiene Moieties and Bis‐phenoxy (3‐hydroxy) Phosphine Oxide System and Properties of Its Cured Polymer

Molecular Dynamics Simulations of Mechanical Properties of Epoxy-Amine: Cross-linker Type and Degree of Conversion Effects

INFLUENCE OF CARBON FIBER IN EPOXY RESIN CURING

Degree of Cure, Microstructures, and Properties of Carbon/Epoxy Composites Processed via Frontal Polymerization

Cure Kinetics of Epoxy Resin Used for Advanced Composites

Effect of rapid manufacturing on the performance of carbon fibre epoxy polymers

Using thermokinetic methods to enhance properties of epoxy resins with amino acids as biobased curing agents by achieving full crosslinking

A review of the curing rate and mechanical properties of epoxy resin on polymer matrix composites

Enhanced Interfacial, Mechanical, and Anti-Hygrothermal Properties of Carbon Fiber/cyanate Ester Composites with the Catalytic Sizing Agents of Titanium Epoxy

Effect of Epoxy Coatings on Carbon Fibers During Manufacture of Carbon Fiber Reinforced Resin Matrix Composites

Influence of preheating and post-curing on a novel fiber-reinforced composite post material

Rapid curing epoxy resin and the properties of carbon fiber/epoxy composite

Cure Kinetic Study of Carbon Nanofibers/Epoxy Composites by Isothermal Dsc

Curing Kinetics Modeling of Epoxy Modified by Fully Vulcanized Elastomer Nanoparticles Using Rheometry Method

Assessment of curing behavior on the characterization of two epoxy resin systems

Research on curing kinetics of multiaxial warp‐knitted composites

The curing kinetics and mechanical properties of epoxy resin composites reinforced by PEEK microparticles

Study on the Curing Behavior of Polythiol/phenolic/epoxy Resin and the Mechanical and Thermal Properties of the Composites

Interplay of curing and thermal degradation in epoxy resins cured with amino acids: Influence of the maximum curing temperature on the network structure, crystal morphology and mechanical properties