Abstract:In this study, in situ nano-ZrB2/2024Al composites fabricated from 2024Al–K2ZrF6–KBF4 system were processed by friction stir processing (FSP) to achieve superplasticity of the composites. And the effects of particle contents (1 wt%, 3 wt%, 5 wt%), matrix grain size (micron or sub-micron), strain rates (5×10−3 s−1, 1×10−2 s−1, 2×10−2 s−1) and deformation temperatures (400 K, 480 K, 600 K, 700 K, 750 K) on the superplasticity of the composites were investigated. After the friction stir processing, the coarse grains of the cast composites with matrix grain size of about 80–100 μm and nano-ZrB2 reinforcement size of 30–100 nm were crushed into small grains about 1 μm in size, and the uniformity of the nano-ZrB2 reinforcements was also improved. And under the same superplastic tensile testing condition at the temperature of 750 K and strain rate of 5×10−3 s−1, the FSP nano 3 wt%ZrB2/2024Al composite exhibited an superplastic elongation of 292.5%, while the elongation of the corresponding cast composite was only less than 100%. Meanwhile, the m values of the FSP composites were always higher than the cast composites, especially the FSP composites with 3 wt% particles has the m value of 0.5321 i.e., the FSP composites should had better superplastic properties than cast ones. Furthermore, the FSP composites had higher apparent deformation activation energy (Q) than that of the lattice diffusion of pure aluminium, indicating that the deformation mechanisms of the FSP composites should be grain boundary sliding mechanisms.

High Strain Rate Superplasticity of a Fine-Grained AZ91 Magnesium Alloy Prepared by Friction Stir Processing

Superplastic Deformation Behavior of Fine-Grained AZ80 Magnesium Alloy Prepared by Friction Stir Processing

Excellent High‐Strain‐Rate Superplasticity of Fine‐Grained ZK60 Magnesium Alloy Produced by Submerged Friction Stir Processing

High Strain Rate Superplasticity in a Micro-grained Al{Mg{Sc Alloy with Predominant High Angle Grain Boundaries

Microstructural Evolution and Enhanced Superplasticity in Friction Stir Processed Mg–Zn–Y–Zr Alloy

High Strain Rate Superplasticity of Rolled AZ91 Magnesium Alloy

Enhancing mechanical properties of AZ61 magnesium alloy via friction stir processing: Effect of processing parameters

Ductility Improvement of an AZ61 Magnesium Alloy through Two-Pass Submerged Friction Stir Processing

Superplasticity and Grain Boundary Sliding in Rolled AZ91 Magnesium Alloy at High Strain Rates

Superplasticity of Fine-Grained AZ31 Mg Alloy Sheets

AZ91 Magnesium Alloy CMT Cladding Layer Processed Using Friction Stir Processing: Effect of Traverse Speed on Microstructure and Mechanical Properties

Multi-pass submerged friction stir processing of AZ61 magnesium alloy: strengthening mechanisms and fracture behavior

Enhanced Corrosion Resistance of AZ91 Magnesium Alloy Through Refinement and Homogenization of Surface Microstructure by Friction Stir Processing

Effects of Friction Stir Processing on the Microstructure and Superplasticity of in Situ Nano-Zrb2/2024al Composite

Microstructures and Mechanical Properties of Friction Stir Processed Mg–2.0Nd–0.3Zn–1.0Zr Magnesium Alloy

Achieving high strain rate superplasticity in an Al-Cu-Li alloy processed by thermo-mechanical processing

High Strain Rate Superplasticity of in situ Al 3 Zr/6063Al Composites

Realization of Exceptionally High Elongation at High Strain Rate in a Friction Stir Processed Al–Zn–Mg–Cu Alloy with the Presence of Liquid Phase

Thermomechanical Processing and Superplasticity of AZ91 Magnesium Alloy

High Strain Rate Superplasticity in Al-Zn-Mg-Based Alloy: Microstructural Design, Deformation Behavior, and Modeling

High Strain Rate Quasi-Superplasticity Behavior in an Ultralight Mg-9.55Li-2.92Al-0.027Y-0.026Mn Alloy Fabricated by Multidirectional Forging and Asymmetrical Rolling