Abstract:Combustion synthesis (CS) is a well-known technique for manufacturing intermetallic compounds and intermetallic-matrix composite materials. This research focuses on fabricating NiAl-matrix composites with varying TiC/TiB2 contents as reinforcement, achieved by the combustion synthesis method. The chemical reactions that yield the final NiAl-TiC-TiB2 compounds were interpreted using thermodynamic calculations. The phase analysis and morphology of the composites were investigated using X-ray diffractometry (XRD) and scanning electron microscopy (SEM) characterization techniques, respectively. The findings demonstrate that the NiAl matrix contains evenly distributed TiC-TiB 2 ceramic-based particles, and no oxidation of reactants occurred during the combustion reaction. With an increase in the TiC-TiB 2 reinforcement phases from 0 to 15 Wt. %, the hardness of the NiAl-TiC-TiB 2 product significantly rose from 496 to 1015 Vickers, while the porosity increased from 24% to 39%, attributed to the reduced quantity of melted NiAl available to fill the pores. Examining tribological behavior in synthesized composites involved combining experimental-numerical methods, utilizing sliding wear tests and artificial neural network (ANN) modeling. The wear results revealed decreasing wear rates with reduced loads (from 35 N to 25, and 15 N) and higher TiC/TiB 2 ceramic content. Iron traces at C0 and C10 worn samples were 2.47 and 26.18 Wt. % respectively, which indicates enhanced hardness. The experimental data were used to train and test an artificial neural network (ANN) and statistical analysis revealed a remarkable accuracy of 91% for the ANN model in predicting friction coefficients within SHS-processed composites, as indicated by the R2 value of 0.91 and a MAPE of 6.47.

Influence of Ti 3SiC 2 content on tribological properties of NiAl matrix self-lubricating composites

Effect of Ti3SiC2 Content on Tribological Behavior of Ni3Al Matrix Self-Lubricating Composites from 25 to 800 °C

Tribological performance of Ti3SiC2 enhanced Ni3Al matrix composites

Tribological Behaviors of NiAl-Ti3SiC2Self-Lubricating Composites at Elevated Temperatures

Tribological properties of TiAl-Ti 3 SiC 2 composites

Tribological Behavior of Ni3Al Matrix Self-Lubricating Composites Containing WS2, Ag and Hbn Tested from Room Temperature to 800°C

Tribological Performance of Ni3Al–15 Wt% Ti3SiC2 Composites Against Al2O3, Si3N4 and WC-6Co from 25 to 800 °C

Synergetic Lubricating Effect of MoS2 and Ti3SiC2 on Tribological Properties of NiAl Matrix Self-Lubricating Composites over a Wide Temperature Range

Tribological Performance Of Ni3al Self-Lubricating Composites With Different Content Of Tic At Elevated Temperature

Effects of Ti3SiC2 on microstructure and properties of TiC0.4 enhanced TiAl matrix composites

Influence of Ti3AlC2 content and load on the tribological behaviors of Ti3AlC2p/Al composites

Friction and Wear Properties of TiAl-Ti3SiC2-MoS2 Composites Prepared by Spark Plasma Sintering

Influence of Si Content on Microstructure and Mechanical Properties of TiAlSiN Nanocomposite Coatings

Effect of TiC Coated MWCNT Content on Friction and Wear Behavior of MWCNT–Ti3SiC2 Composites

Synergetic Lubricating Effect of WS2 and Ti3SiC2 on Tribological Properties of Ni3Al Matrix Composites at Elevated Temperatures

Effect of Ni content on the wear behavior of Al-Si-Cu-Mg-Ni/SiC particles composites

Wear and Friction of TiAl Matrix Self-Lubricating Composites against Si3N4 in Air at Room and Elevated Temperatures

Fabrication and Assessment of Dry Sliding Behavior of Ti3C2Tx-MXene Reinforced Nickel Aluminide Composites

Fabrication and wear behavior of TiC/TiB 2 -reinforced NiAl intermetallic matrix composites

Effects of MoS 2 and Multiwalled Carbon Nanotubes on Tribological Behavior of TiAl Matrix Composite

The Study of the Preparation and Tribological Behavior of TiAl Matrix Composites Containing 1 Wt% Multi-Walled Carbon Nanotubes