Abstract:NiCr–Mo–Bi2O3/TiO2 composites were prepared by vacuum hot-press sintering technology. The oxides of Bi4Ti3O12, Cr2O3 and Ti2O3 were formed by the reaction of Cr, Bi2O3 and TiO2 during the sintering process. The intensity of Bi4Ti3O12, Cr2O3 and Ti2O3 diffraction peaks became higher with the incremental content of Bi2O3 and TiO2. Mo element was mainly distributed in the matrix, which had the effect of solid solution strengthen in the composites. The microhardness and yield strength improved with addition of Mo. With Bi2O3 and TiO2 adding, the microhardness obviously increased. The microhardness of NiCr–10Mo–30Bi2O3/TiO2 composite was the highest of 491.6 HV. Nevertheless, the yield strength and ultimate strength significantly decreased. It may be caused by cracks in the interface between metallic oxides and matrix, where stress concentration would occur. The NiCr–10Mo–20Bi2O3/TiO2 composite had the lowest wear rate of 2.1×10−5 mm3/Nm, which was probably due to the oxidation layer was very dense and was very hard to shed in the process of friction. The composites after adding of Bi2O3 and TiO2 presented the excellent tribology property due to the fact that the Bi4Ti3O12 formed on the worn surfaces which had been proved to be an outstanding lubricant at high temperature.

The microstructure characteristics and self-lubrication mechanism of the NiAl matrix composites prepared by vacuum hot-pressing sintering

Investigation on Microstructure and Wear Behavior of the NiAl–TiC–Al2O3 Composite Fabricated by Self-Propagation High-Temperature Synthesis with Extrusion

Wear Properties of NiAl Based Materials

High temperature and room temperature tribological behaviors of in-situ carbides reinforced Ni-based composites by reactive sintering Ni and Ti2AlC precursor

Microstructure and mechanical properties of Ti3(Al,Ga)C2/Al2O3 composites prepared by in situ reactive hot pressing

Microstructure Evolution and Mechanical Properties of Ni3al/Al2o3 Composite During Self-Propagation High-Temperature Synthesis and Hot Extrusion

Microstructure and Wear Behaviour of Ceramic Particles Strengthening Nial Based Composite

Investigation of Friction and Wear Behavior of NiAl-based Alloys at Room Temperature

Investigation on NiAl–TiC–Al2O3 Composite Prepared by Self-Propagation High Temperature Synthesis with Hot Extrusion

Microstructure and Mechanical Properties of Multiphase Strengthened Al/Si/Al 2 O 3 /SiO 2 /MWCNTs Nanocomposites Sintered by In Situ Vacuum Hot Pressing

Microstructure, Friction, And Wear Properties Of Ni-Al2o3-Mos2 Composite Coatings

Influence of Ti3AlC2 content and load on the tribological behaviors of Ti3AlC2p/Al composites

Effects of Ag2Mo2O7 nano-shapes on the mechanical and tribological properties of NiAl intermetallic compound over a wide temperature range

High temperature tribological behaviors and wear mechanisms of NiAl-MoO3/CuO composite coatings

Microstructure, mechanical properties and tribological behaviors of TiAlN-Ag composite coatings by pulsed magnetron sputtering method

Effect of Temperature on Tribological Properties of Tial Based Self-Lubricating Composites

Processing, Microstructural Characterization and Mechanical Properties of in Situ Ti3AlC2/TiAl3 Composite by Hot Pressing

Effects of Ni-5 wt% Al/Bi2O3 addition and heat treatment on mechanical and tribological properties of atmospheric plasma sprayed Al2O3 coating

Improved tribological performance of nickel based high temperature lubricating composites with addition of metallic oxides

Tribological behavior of NiCrW-based self-lubricating composites against IC10 alloy under high temperature and extremely slow sliding speed

Microstructure and tribological properties evolution of Ni-Mo-SrSO 4 composites as a function of Mo contents at different temperatures