Abstract:In recent years, the addition of Ni has been widely acknowledged to be capable of enhancing the mechanical properties of Al-Si alloys. However, the effect of Ni on the wear behaviors of Al-Si alloys and Al matrix composites, particularly at elevated temperatures, remains an understudied area. In this study, Al-Si-Cu-Mg-Ni/20wt% SiC particles (SiCp) composites with varying Ni contents were prepared by using a semisolid stir casting method. The effect of Ni content on the dry sliding wear behavior of the prepared composites was investigated through sliding tests at 25 and 350°C. Results indicated that the θ-Al 2 Cu phase gradually diminished and eventually disappeared as the Ni content increased from 0wt% to 3wt%. This change was accompanied by the formation and increase in δ-Al 3 CuNi and ε-Al 3 Ni phases in microstructures. The hardness and ultimate tensile strength of the as-cast composites improved, and the wear rates of the composites decreased from 5.29 × 10 −4 to 1.94 × 10 −4 mm 3 /(N·m) at 25°C and from 20.2 × 10 −4 to 7 × 10 −4 mm 3 /(N·m) at 350°C with the increase in Ni content from 0wt% to 2wt%. The enhancement in performance was due to the presence of strengthening network structures and additional Ni-containing phases in the composites. However, the wear rate of the 3Ni composite was approximately two times higher than that of the 2Ni composite due to the fracture and debonding of the ε-Al 3 Ni phase. Abrasive wear, delamination wear, and oxidation wear were the predominant wear mechanisms of the investigated composites at 25°C, whereas delamination wear and oxidation wear were dominant during sliding at 350°C.

Investigation of Friction and Wear Behavior of NiAl-based Alloys at Room Temperature

Wear Properties of NiAl Based Materials

Fabrication and performance of Ni-Co-P/Si3N4 electroplated composite coatings on al-si alloys

Friction and Wear Behavior of NiAl–10wt%Ti3SiC2 Composites

Investigation on Microstructure and Wear Behavior of the NiAl–TiC–Al2O3 Composite Fabricated by Self-Propagation High-Temperature Synthesis with Extrusion

Microstructure, Mechanical Properties and High Temperature Tribological Behavior of NiAl-based Composites

Microstructure and Wear Behaviour of Ceramic Particles Strengthening Nial Based Composite

Effect of Ni content on the wear behavior of Al-Si-Cu-Mg-Ni/SiC particles composites

High Temperature Wear Behavior of Nial-Cr(Mo)-Ho-Hf Eutectic Alloy

Tribological Behavior of In-Situ (cr, Mo)/Fe3al-20 Wt.%Al2o3 Composites at Elevated Temperatures

Tribological behaviors of nanotwinned Al alloys

Study of Wear Resistance of Centrifugal Cast Binary Titanium Alloys

Tribological behavior of NiCrW-based self-lubricating composites against IC10 alloy under high temperature and extremely slow sliding speed

Effects of Ni-5 wt% Al/Bi2O3 addition and heat treatment on mechanical and tribological properties of atmospheric plasma sprayed Al2O3 coating

Tribological Properties of High Velocity Arc Sprayed FeAlCr/Ni Wraped Cr3C2 Coatings

Effect of Ti3AlC2 Content on Electrical Friction and Wear Behaviors of Cu–Ti3AlC2 Composites

Study on Dry Sliding Friction and Wear Properties of Ti2AlN/TiAl Composite

Friction and Wear Properties of AlNP/Al and TiB2P/Al Composites

Tribological Properties of in Situ Fe3al-20 Wt% Al2o3 Composites

Friction and wear behaviors of Al 2 O 3 /TiC micro-nano-composite ceramic sliding against metals and hard materials

Study on Dry Friction and Wear Properties of TiAl Alloy