Abstract:High-entropy alloys (HEAs) of AlxCoCrFeNi (x = 0.2, 0.5, and 1) were created using the spark plasma sintering (SPS) method in conjunction with an aerosolized powder. Their microstructure and phase constituents were characterized by X-ray diffractometry, scanning electron microscopy, and projection electron microscopy. The tensile properties, hardness, compactness, and damping properties were also tested. The results showed that the crystal structure of AlxCoCrFeNi HEAs changed significantly with the Al content, from the original single face-centered cubic FCC phase (Al0.2CoCrFeNi) to an FCC + BCC + B2 structure (Al0.5CoCrFeNi), and then to FCC + BCC + B2 + Sigma (σ) phase structures (AlCoCrFeNi). Twin crystals with FCC structure were also observed in the TEM of AlCoCrFeNi. A chemical composition analysis showed that the crystal structure transformation was related to the segregation caused by the increase of Al element content. The hardness of the AlxCoCrFeNi HEAs increased with the Al content, and the hardness of AlCoCrFeNi reached the highest value of 585.4 HV. The tensile properties of the alloy showed a trend of increasing and then decreasing values with the increase in Al content. The yield strength, ultimate tensile strength, and elongation of the Al0.5CoCrFeNi alloy reached the highest values of 557.7 MPa, 954.4 MPa, and 32.2%, respectively. Moreover, the fracture mechanism of the Al0.2CoCrFeNi and Al0.5CoCrFeNi alloys was that of a typical ductile fracture, while for the AlCoCrFeNi alloy, it was that of a cleavage fracture. The compactness of the alloy increased with the Al content. The combination of the FCC + BCC + B2 phase resulted in the damping capacity of Al0.5CoCrFeNi alloy reaching 0.018 at the corresponding strain amplitude of 6 × 10−4.

Fabrication and Properties of Nanocrystalline Co0.5FeNiCrTi0.5 High Entropy Alloy by MA–SPS Technique

Preparation and properties of FeNiMnCuC0.2Alx high-entropy alloy

Nano-Structure Evolution and Mechanical Properties of AlxCoCrFeNi2.1 (x = 0, 0.3, 0.7, 1.0, 1.3) High-Entropy Alloy Prepared by Mechanical Alloying and Spark Plasma Sintering

Microstructural Evolution and Mechanical Properties of Al0.3CoCrFeNiSix. High-Entropy Alloys Containing Coherent Nanometer-Scaled Precipitates

Microstructure and Properties of NiCoCrAlTi High Entropy Alloy Prepared Using MA-SPS Technique

Microstructural features and excellent compression properties of a novel Al0.7CoCrFeNiTi0.3 high entropy alloy

Microstructural evolution and mechanical properties of novel nanoparticles strengthened CoCrFeNi based high entropy alloy

Microstructure and mechanical properties of Al-Fe-Co-Cr-Ni high entropy alloy fabricated via powder extrusion

Microstructure and Magnetic Characteristics of AlCrCuFeNiTi High-Entropy Alloy Prepared by Mechanical Alloying Followed by Spark Plasma Sintering

Microstructure and Mechanical Properties of Ultrafine Grained CoCrFeNi and CoCrFeNiAl0.3 High Entropy Alloys Reinforced with Cr2O3/Al2O3 Nanoparticles

Microstructure and mechanical properties of CoCrFeNiTa high entropy alloy prepared by mechanical alloying and spark plasma sintering

The Influence of Ball Milling Time and Sintering Temperature on the Structural and Capabilities of FeCoCrNiMn High-Entropy Alloy

Microstructure, Mechanical Properties, and Damping Capacity of AlxCoCrFeNi High-Entropy Alloys Prepared by Spark Plasma Sintering

Microstructural Characterization and Mechanical Properties of an Al0.5CoCrFeCuNi High-Entropy Alloy in As-Cast and Heat-Treated/quenched Conditions

Analyzing the Phase evolution, Microstructure and Wear Response of Spark Plasma Sintered Al0.5CoCrFeNi2 High Entropy Superalloy

Microstructure, deformation behavior, and dynamic recrystallization kinetics of FeNiMnCu-based high entropy alloys prepared by mechanical alloying and spark plasma sintering

Microstructure evolution and mechanical properties of CoCrFeNiAl0.3 high entropy alloy produced by ball milling in combination with thermomechanical consolidation

Microstructure and mechanical properties of a high entropy alloy with a eutectic composition (AlCoCrFeNi2.1) synthesized by mechanical alloying and spark plasma sintering

Magnetic and mechanical properties of nanotwin SiO 2 -FeCoNi(AlSi) 0.4 high entropy alloy prepared by mechanical alloying and spark plasma sintering

Synthesis and Phase Evolution of a Nanocrystalline FexCrNiAl (x = 1.0, 0.5, 0.25) High-Entropy Alloys by Mechanical Alloying

Microstructure, Hardness, Wear Resistance, and Corrosion Resistance of As-Cast and Laser-Deposited FeCoNiCrAl0.8Cu0.5Si0.5 High Entropy Alloy